Crosley Furniture Tribeca KO70037 User manual

KO70037
Outdoor Wicker Conversation Set

2
PART LIST
A B CD
F
Left Arm
3 PCS
Panel
3 PCS
Right Arm Panel Back Panel
2 PCS
Seat Panel
2 PCS
E
HARDWARE LIST
#1 #2 #3 #4
18 PCS (Extra 2) 20 PCS (Extra 2) 46 PCS (Extra 2)
M6*30mm M6*40mm M6mm
Long Bolt
Back Panel
1 PC
(loveseat)
(loveseat)
Seat Panel
1 PC
GHIJ
Top
1 PC
Panel Leg
4 PCS
Shelf
1 PC
Glass Top
1 PC
K
4 PCS
Back Cushion
Seat Cushion
4 PCS
L
(arm chair) (arm chair)
Short Bolt
8 PCS (Extra 1)
M6*15mm
#5
1 PC
M6mm
Medium Bolt Flat Washer Allen Wrench

3
#3 x2
#4 x2
#5 x1
#3 x1
#4 x4
#5 x1
Step 1.
Attach back panel (part C) to left arm panel (part A) using long bolts (part #3), flat washers
(part #4) and allen wrench (part #5).
NOTE: Please do not fully tighten bolts until unit is fully assembled.
Lay left arm panel (part A) down on a soft flat surface, such as carpet, as shown below.
Step 2.
bolts (part #2), long bolt (part #3), flat washers (part #4) and allen wrench (part #5).
Attach seat panel (part D) to left arm panel (part A) and back panel (part C) using medium
#5
#3
#4
#4
#3
#5
#2 x3
NOTE: Please do not fully tighten bolts until unit is fully assembled.
#4#3
#5
#5
#2
#4
#5
#2
#4

4
#3 x2
#4 x5
#5 x1
Step 3.
Attach right arm panel (part B) to assembled unit (parts A, C & D) using medium bolts (part #2)
long bolts (part #3), flat washers (part #4) and allen wrench (part #5).
NOTE: Please fully tighten all bolts at this time.
Step 4.
Carefully turn unit upright. Place seat cushion (part K) and back cushion (part L) as shown below.
#2 x3
#5
#3
#4 #4
#3
#5
#4
#2
#5
#4
#2
#5
K
L
Repeat steps 1-4 to assemble remaining chair.

5
#3 x2
#4 x2
#5 x1
#3 x2
#4 x5
#5 x1
NOTE: Please do not fully tighten bolts until unit is fully assembled.
#5
#3
#4
#4
#3
#5
#2 x3
#4#3
#5
#5
#2
#4
#5
#2
#4
E
Step 5.
Attach back panel (part E) to left arm panel (part A) using long bolts (part #3), flat washers
(part #4) and allen wrench (part #5).
Lay left arm panel (part A) down on a soft flat surface, such as carpet, as shown below.
F
E
Step 6.
bolts (part #2), long bolts (part #3), flat washers (part #4) and allen wrench (part #5).
Attach seat panel (part F) to left arm panel (part A) and back panel (part E) using medium
NOTE: Please do not fully tighten bolts until unit is fully assembled.

as shown below.
6
#3 x2
#4 x5
#5 x1
#2 x3
#5
#3
#4 #4
#3
#5
#4
#2
#5
#4
#2
#5
Step 7.
Attach right arm panel (part B) to assembled unit (parts A, E & F) using medium bolts (part #2)
long bolts (part #3), flat washers (part #4) and allen wrench (part #5).
NOTE: Please fully tighten all bolts at this time.
E
F
Step 8. Carefully turn unit upright. Place seat cushions (part K) and back cushions (part L)
K
L

7
#1 x8
#4 x8
#5 x1
#3 x4
#4 x4
#5 x1
Step 9.
Attach legs (part H) to top panel (part G) using short bolts (part #1), flat washers
(part #4) and allen wrench (part #5).
NOTE: Please do not fully tighten bolts until unit is fully assembled.
Lay top panel (part G) down on a soft flat surface, such as carpet, as shown below.
Step 10.
allen wrench (part #5).
NOTE: Please fully tighten all bolts at this time.
Attach shelf (part I) to legs (part H) using long bolts (part #3), flat washers (part #4) and
#5
#1
#4
#5
#1
#4
#5
#3
#4
G
H
G
H
I

8
Step 11.
Turn the table upright and gently place glass top (part J) on holders of top panel (part G).
H
G
I
J