Crosley CF91007-604 User manual

King Canopy Bed
CF91007-604

PART LIST
A
Panel
2 PCS
B C
Footboard Leg
2 PCS
D
Finial
4 PCS
E
Footboard Post
2 PCS
F
Headboard Post
2 PCS
G
Long Canopy Pole
2 PCS
H
Short Canopy Pole
2 PCS
I
Side Rail
2 PCS
J
End Slat
2 PCS
K
HARDWARE LIST
#1
Bolt
8 PCS (Extra 1)
1/4" x 5/8"L
#2
Medium Bolt
4 PCS (Extra 1)
1/4" x 3/4"L
#3
Short Sunk Bolt
4 PCS (Extra 1)
1/4" x 1-7/8"L
#4
Hex Nut
12 PCS (Extra 1)
1/4"
#6
Flat Washer
18 PCS (Extra 1)
Ø16xØ6.5x1MM
#7 #8 #9
Allen Wrench
1 PC
Wrench
1 PC
Long Bolt
6 PCS (Extra 1)
1/4" x 1-1/2"L
2
Headboard Leg
2 PCS
L
Support Leg
6 PCS
Center Slat
2 PCS
Long Sunk Bolt
12 PCS (Extra 1)
1/4" x 2-1/4"L
#5

Step 1. Lay panel (part A) upside down on a soft flat surface, such as carpet, as shown below. Attach headboard
legs (part B) to panel (part A) using long sunk bolts (part #5) and allen wrench (part #8).
Note: Please fully tighten all bolts at this time.

Step 3. Carefully turn assembled unit (parts A & B) upright. Attach side rails (part I) to headboard legs (part B)
using short sunk bolts (part #4), hex nuts (part #6), allen wrench (part #8) and wrench (part #9). See
Figure 1. Carefully turn assembled unit (parts A & C) upright. Attach side rails (part I) to footboard legs
(part C) using medium bolts (part #2), flat washers (part #7) and allen wrench (part #8).
See Figure 2.
Note: Please do not fully tighten bolts until unit is fully assembled.
#8 x1
B
#8
#4
#6
#8
#2 C
#9 x1
#9
#2 x4
#7
#5 x6
#8
#6
#7
#4
x1
x4
x4
x4
I
I
3
A
B
I
A
Figure 1
Figure 2
A
B
A
B
B
Step 2. Lay panel (part A) upside down on a soft flat surface, such as carpet, as shown below. Attach footboard
legs (part C) to panel (part A) using long sunk bolts (part #5) and allen wrench (part #8).
Note: Please fully tighten all bolts at this time.

#8 x1
#5 x6
A
C
A
C
C
C
#5
#5
#5
#5
#8
#8

Step 5. Attach assembled units (parts J, K & L) to side rails (part I) using bolts (part #1), flat washers
(part #7), hex nuts (part #6), allen wrench (part #8) and wrench (part #9).
Note: Please fully tighten all bolts at this time.

Step 6. Screw finials (part D) on headboard legs (part B) and footboard legs (part C) by hand.
#8 x1
#7
#6
x8
x8
#8
#3
x1
x6
#1 x8
x1
#9
#1
#7
#6
#9
#8
J & K
I
#3
#8
J & K
L
D
B & C
Step 4. Attach support legs (part L) to the bottom of end slats (part J) and center slats (part K) using long
bolts (part #3), flat washers (part #7) and allen wrench (part #8).

#7
#7 x6
4
J
L
L
K
I
D
B
C
K
L
J
A
A

D
G
H
E & F
Step 8. Insert headboard posts (part F) onto headboard legs (part B) and footboard posts (part E) onto
footboard legs (part C).

E & F
B & C
Canopy Assembly:
Step 7. Remove finials (part D) from headboard legs (part B) and footboard legs (part C) by hand.
Carefully line up holes on long canopy poles (part G) and short canopy poles (part H) to
footboard posts (part E) and headboard posts (part F) and secure with finials (part D).

5
D
G
H
EF
F
B
C
E