Crosswater KL0007WC User manual

INSTALLATION INSTRUCTIONS
For any furtherinformation please contact
Crosswater on: 0845 873 8840
Or visit our web-site at www.crosswater.co.uk
The manufacturer reservesthe right tomake technical
modifications without priornotice.
P5-Z0A158-E A/1
KL0007WC
4 Way Diverter wall mounted

12
INTRODUCTION DIMENSIONS
NOTE: ALLDIMENSIONS IN MILLIMETRES
KL0007WC
PARTS IDENTIFICATION
NOTE: ALLDIMENSIONS IN MILLIMETRES
38
53
8
2-G1/2
96
32
50
60-66
114
34
60
3-G3/4
HOT
INLET
COLD
INLET
MAIN OUTLET
(SHOWER-FIXED HEAD)
This divertervalve issuitable foruse withall watersystems witha operating
pressure 1Bar upto 5.0bar, (beyond which we recommend pressure reducing
valves tobe fitted).
The valvehas threeoutlets thatallow foradditional fittingsto besupplied.
BATH BODY JETS
OR HAND SHOWER
BATH
BODY JETS
OR HAND SHOWER

INSTALLATION
34
HEXAGONAL KEY
HANDLE
VALV E
INSTALLATION
First shutoff yourwater heating system then, with your mains stop cock closed,
open thelowest hotand coldtaps inthe houseand allowto rununtil thecold
storage tankand pipesare empty(the hotwater storagecylinder always
remains full).
Where combinationboilers arefitted itis onlynecessary toturn offthe boiler
and shutoff theincoming mains.
Fitting isolatingvalves tothe inletfeeds isrecommended forease of
maintenance.
INSTALLATION
Remember toturn offthe mainswater supplybefore connectingto
any existingpipe work.
Warning! Please checkfor anyhidden pipes and cables before
drilling holesin thewall
!
Once youhave satisfiedyourself thatthere areno leaks,switch onthe water
heating.
!
ATTENTION
Having firstchecked allnew connections,turn onthe mainsstop cock,close
all tapsexcept thenew mixerand asthe systemstarts torefill checkfor leaks.
KL0007WC
COVER PLATE
BLANKING CAP(OPTIONAL)
3/8 FEMALE TO 1/2MALE ADAPTORS
The valveis securedin placeby meansof rigid(clipped) pipework. Makesure
the valveis setback fromthe frontface ofthe wallby theappropriate depth
to allowfor plasterboard,filling andtiling etc.
Inlets andoutlets are & ports.Make allpipe workconnections usinga
proprietary threadsealer. Do not use tapered threaded adaptors.
Blank offand seal the open outlet if it is not required.
Apply anarrow beadof clearsilicone sealantaround theback edgeof the
cover plateand carefullypress intoposition.
Fit thecontrol knobsby liningup theflat surfaceof thevalve coverwith the
grub screwon thehandle, tightenthe screwwith thesupplied hexagonalkey.
1/2" 3/4"

KL0007WC
6
5
The chrome andgold plate weuse on our taps is very durable, nevertheless care should
be taken whencleaning them. They should be cleaned only with warm soapy water
followed by rinsingwith clean waterand drying with a soft cloth. All finishes are vulnerable
to acid attackand some strongsubstances such as household cleaners, disinfectants,
denture cleaners, hairdyes, wine makingand photographic chemicals can cause the
surface to goblack or peel.
CLEANING
CLEANING THECARTRIDGE
The concealedcartridge should give trouble free service, but in the event of any
problems, servicingis straightforward.
MAINTENANCE
To remove the cartridge.
First shutoff thewater supply then loosen the grub screw and remove the handle.
Take offthe cover plate & threaded collar. Take offand keep safe the washer and
spindle beforeunscrewing theretaining nut.
Takingnote of the orientation of the cartridge remove it.
Wash the cartridgewith cleanrunning water, dry and lightly grease the seal.
HEXAGONAL KEY
HANDLE
CARTRIDGE
WASHER
COVER PLATE
THREADED
COLLAR
SPINDLE
RETAINING NUT
VALV E