Crosswater Alo Furniture Range User manual

1
ALO
IMPORTANT INFORMATION BEFORE YOU START
Please read carefully and keep this information for further reference.
Furniture Range
i
Thank you for buying a Crosswater Product. To ensure that it
works to its full potential, it needs to be tted correctly.
Check the contents of the pack carefully before installation.
Crosswater will not be held responsible for any de-t/re-t
costs where faulty product has been tted. If any fault is
found with materials or workmanship, it must be reported
immediately to the manufacturer. Remedial action will be
taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer.
2. The product has not been modied or tampered with;
3. The manufacturer is informed of any damage/shortages
prior to installation.
4. The product has not been installed, or attempts have been
made to install.
We do not accept responsibility for any problems that may
occur through incorrect installation. This product should
only be installed by a suitably qualied plumber/installer.
Should the installation be completed by a non-qualied
person any product guarantee maybe considered invalid. For
a claim made under our warranty, written certication of your
installer’s qualications may be required.
V10623

2
IMPORTANT INFORMATION
Please read carefully and keep this information for further reference.
Please check for any hidden pipes or electrical cables before drilling holes in the oor or walls. When using power tools always
follow the manufacturer’s user instructions. This installation guide details tting to a solid wall. If your bathroom has studded/
plasterboard walls, please use appropriate xings.
Make sure that the wall can take the weight of the products before undertaking the installation.
Waste ttings should be carefully bedded in silicone and the back nut hand tightened; an additional quarter turn using a
suitable spanner is suicient to create the required watertight seal.
It is advised that all doors and drawers are removed prior to tting to avoid unnecessary damage occurring.
It is recommended that the furniture and accessories are installed aer tiling, ensuring that the product is installed at to the
tile face and allows product to be easily removed if required in the future.
This document has been prepared for your guidance, you must exercise due care at all times.
Please note that some units are heavy. Always take care when liing, and follow health and safety guidelines. It is
recommended that 2 people carry out the installation of larger basin/vanity units over 30Kgs gross weight.
If any maintenance is required then it must be carried out by a qualied Plumber. The manufacturer reserves the right to make
technical modications without prior notice.
Drill + 8mm Drill Bit Pencil
Screw Driver
Tape Measure
Spirit Level
Adjustable Spanner
Safety Goggles
Tools Required (not supplied):
Water Based
Silicone Sealant
BEFORE YOU START

3
x4 x2
AL0401URx 3.8kg AL4000Fxx 10kg Rattan Finish
AL4000Fxx 10kg
COMPATIBILITY
FIXINGS

4
B
A
Ø8
INSTALLATION
3
Determine the position and height of the unit, ensuring
the recommended heights are followed. Ensure the
measurements and markings you make are straight. Check
that the plumbing connections from the wall are within the
void provided.
Measure the width and height of the xing brackets -
distances B and C. Mark the wall and prepare to drill.
Remove the door from furniture carcass by releasing using
the button to the rear of the hinges.
1
Drill the marks using an 8mm drill bit and ensuring there are
no hidden pipes or cables in the wall. Make sure the correct
drill bit is used for the surface being drilled and check that the
holes are level.
4
870mm
A
B
C
A
B
C
2

5
INSTALLATION
6
5
Install the wall brackets using the xings provided. The
unit carcass can now be mounted on the wall brackets and
adjusted to ensure it is ush with the wall and level.
The tap and waste ttings may now be installed, following the
manufacturer’s instructions.
Connect water and waste pipework and turn on the water
supply to check for any leaks.
Important: Apply silicone sealant on the top of the basin unit
to keep watertight. Check the manufacturer’s instructions for
drying times.
78
Apply silicone sealant at the back and top of the basin
and unit to keep watertight. Check the manufacturer’s
instructions for drying times.
To avoid damaging the door, place the door face down on a
composite board. Drill through the pilot hole on the door for
the handle you have selected.
NOTE: Rattan front panels don’t require drilling, they have a
built-in side handle.

6
INSTALLATION
10
9
Return the door to the unit by aligning the door hinges
to the brackets on the inside of the unit and slide the two
components together.
If reversing the handing of the door, the base of the hinges
can be removed and placed on the opposite side of the
carcass, using the pilot holes provided.
Door can be adjusted as shown below:

7
Part of the
Bathroom Brands Group
Lake View House
Rennie Drive, Dartford
Kent DA1 5FU
United Kingdom
0345 873 8840
www.crosswater.co.uk
We reserve the right to make technical modications without prior notice.
Clean regularly using with warm soapy water and polish with only a so cloth.
Any residues from soap, toiletries etc. should be rinsed o straight aer use.
Household bleaches and cleaners containing harsh chemicals may damage the surface nish.
Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.
Lime-scale marks can be cleaned using a diluted lime-scale remover used in accordance with manufacturers instructions.
Ceramic, glass and cast mineral marble basin products should be cleaned regularly with warm soapy water, then rinsed with
clean water and, if desired, dried and polished with a so cloth. Lime scale deposits can be removed using a 50:50 solution of
warm water and lime scale remover and so clean cloth.
We recommend regular cleaning with Cream Polish SD150RW, specially formulated to clean and help protect the surface of
glass and cast mineral marble basins. Please also take care not to damage the lacquered surface on the underside of the glass
washbasin that gives the washbasin its colour. Damage to the underside of the washbasin may be visible through the glass.
Take care how you handle the washbasin prior to installation and place it on a so surface to avoid damage. Regularly clean
worktop, carcass and drawer using a micro-bre cloth. Do not use abrasive cleaners or bleach as this will permanently damage
the lacquered surfaces. If any maintenance is required then it must be carried out by a qualied Plumber.
Rattan is a natural material that is water resistant and durable, however, care should be taken to ensure its longevity. Clean
using a handheld vacuum or a brush attachment or a damp cloth. Avoid entirely any chemicals.
Avoid pressing heavily against the rattan as this may cause it to release from the door frame.
CARE & MAINTENANCE