Crosswater Mada User manual

1
MADA
IMPORTANT INFORMATION BEFORE YOU START
Please read carefully and keep this information for further reference.
Furniture Range
i
Thank you for buying a Crosswater Product. To ensure that it
works to its full potential, it needs to be tted correctly.
Check the contents of the pack carefully before installation.
Crosswater will not be held responsible for any de-t/re-t
costs where faulty product has been tted. If any fault is
found with materials or workmanship, it must be reported
immediately to the manufacturer. Remedial action will be
taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer.
2. The product has not been modied or tampered with;
3. The manufacturer is informed of any damage/shortages
prior to installation.
4. The product has not been installed, or attempts have been
made to install.
We do not accept responsibility for any problems that may
occur through incorrect installation. This product should
only be installed by a suitably qualied plumber/installer.
Should the installation be completed by a non-qualied
person any product guarantee maybe considered invalid. For
a claim made under our warranty, written certication of your
installer’s qualications may be required.
V1.05.2023

2
IMPORTANT INFORMATION
Please read carefully and keep this information for further reference.
i
Please check for any hidden pipes or electrical cables before drilling holes in the oor or walls. When using power tools always
follow the manufacturer’s user instructions. This installation guide details tting to a solid wall. If your bathroom has studded/
plasterboard walls, please use appropriate xings.
Make sure that the wall can take the weight of the products before undertaking the installation.
Waste ttings should be carefully bedded in silicone and the back nut hand tightened; an additional quarter turn using a
suitable spanner is suicient to create the required watertight seal.
It is advised that all doors and drawers are removed prior to tting to avoid unnecessary damage occurring.
It is recommended that the furniture and accessories are installed aer tiling, ensuring that the product is installed at to the
tile face and allows product to be easily removed if required in the future.
This document has been prepared for your guidance, you must exercise due care at all times.
Please note that some units are heavy. Always take care when liing, and follow health and safety guidelines. It is
recommended that 2 people carry out the installation of larger basin/vanity units over 30Kgs gross weight.
If any maintenance is required then it must be carried out by a qualied Plumber. The manufacturer reserves the right to make
technical modications without prior notice.
Drill + 8mm Drill Bit Pencil
Screw Driver
Tape Measure
Spirit Level
Adjustable Spanner
Safety Goggles
Tools Required (not supplied):
Water Based
Silicone Sealant

3
COMPATIBILITY
FIXINGS
MA050xSRx 9kg
MA500Txx 5Kg
MA5000Dxx 15kg
MA500SFxx 5kg
x4 x2 x1 Overow tting
supplied with Cast
Marble basins only
MA060xSRx 9kg
MA600Txx 5Kg
MA6000Dxx 15kg
MA600SFxx 5kg
MA070xSRx 9kg
MA700Txx 5Kg
MA7000Dxx 15kg
MA700SFxx 5kg

4
860/870mm
860/870mm
A
B
C
B
A
Ø8
INSTALLATION
12
3 4
Remove the drawer by pulling it forward approximately 10cm
before the limit stop and pressing the clips on the underside
of the drawer. The drawer will release from the guide and
it can be gently lied. Place on a safe location ensuring no
impact or damage to the drawer.
Determine the position and height of the unit, ensuring
the recommended heights are followed according to the
combination of basin and tap selected.
Measure the width and height of the xing brackets -
Distances B and C. Mark the wall and prepare to drill.
Drill the marks using an 8mm drill bit and ensuring there are
no hidden pipes or cables in the wall. Make sure the correct
drill bit is used for the surface being drilled and check that the
holes are level.

5
INSTALLATION
Install the wall brackets using the xings provided. The
unit carcass can now be mounted on the wall brackets and
adjusted to ensure it is ush with the wall and level.
The tap and waste ttings may now be installed, following the
manufacturer’s instructions.
Connect water and waste pipework and turn on the water
supply to check for any leaks.
Important: Apply silicone sealant on the top of the basin unit
to keep watertight. Check the manufacturer’s instructions for
drying times.
The tap and waste ttings may now be installed, following the
manufacturer’s instructions.
Connect water and waste pipework and turn on the water
supply to check for any leaks.
Important: Apply silicone sealant on the top of the basin unit
to keep watertight.
Apply silicone sealant at the back and top of the basin
and unit to keep watertight. Check the manufacturer’s
instructions for drying times.
56
87

6
±2 L / R
±1
L / R
!
L / R
INSTALLATION
Return the drawer to its position, by fully extending the
drawer guides on the carcass and placing the drawer on the
guides. Push the drawer into the carcass until a “click” is
heard. Check that the drawer is sitting correctly on the guides
and functioning correctly. It should open smoothly and so-
close.
The drawer front can now be adjusted from the inside to
ensure it is level with the carcass. Once the adjustment has
been completed the lock should be applied.
Optional under-mount shelf & frame.
Important: the side of the frame with the 20mm thickness
goes on the bottom.
Fit the wood shelf to the steel frames using the screws
provided. The shelf is pre-drilled with pilot holes to ensure a
perfect t to the basin unit.
Once the under-mount shelf & frame is assembled, it can be
tted to the vanity unit using the screws provided. The vanity
unit is pilot-drilled on the underside to guide the assembly.
Do not exceed the weight capacity of 30kg
910
20mm
1211

7
Part of the
Bathroom Brands Group
Lake View House
Rennie Drive, Dartford
Kent DA1 5FU
United Kingdom
0345 873 8840
www.crosswater.co.uk
We reserve the right to make technical modications without prior notice.
Clean regularly using with warm soapy water and polish with only a so cloth.
Any residues from soap, toiletries etc. should be rinsed o straight aer use.
Household bleaches and cleaners containing harsh chemicals may damage the surface nish.
Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.
Lime-scale marks can be cleaned using a diluted lime-scale remover used in accordance with manufacturers instructions.
Ceramic, glass and cast mineral marble basin products should be cleaned regularly with warm soapy water, then rinsed with
clean water and, if desired, dried and polished with a so cloth. Lime scale deposits can be removed using a 50:50 solution of
warm water and lime scale remover and so clean cloth.
We recommend regular cleaning with Cream Polish SD150RW, specially formulated to clean and help protect the surface of
glass and cast mineral marble basins. Please also take care not to damage the lacquered surface on the underside of the glass
washbasin that gives the washbasin its colour. Damage to the underside of the washbasin may be visible through the glass.
Take care how you handle the washbasin prior to installation and place it on a so surface to avoid damage. Regularly clean
worktop, carcass and drawer using a micro-bre cloth. Do not use abrasive cleaners or bleach as this will permanently damage
the lacquered surfaces. If any maintenance is required then it must be carried out by a qualied Plumber.
CARE & MAINTENANCE