Crosswater ZION FLOOR STANDING 60 User manual

BATHROOM FURNITURE RANGE
IMPORTANT - Advice and safety - Please read before installation
ZION FLOOR STANDING 60-70-120
1200 Two Drawer Basin Unit & Basin
Tools & equipment needed: Drill, 8mm Suitable drill bit, Phillips screwdriver, Spirit level, Ruler/tape measure,
Pencil, Silicone sealant (clear).
To ensure full working use of
the drawers we recommend
the use of Bauhaus basin
furniture trap BTR0510W
Zion Floor Standing Furniture
Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Crosswater will not be held responsible for any de-fit / re-fit costs
where faulty product has been fitted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will
be taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modified or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualified
Plumber/installer. Should the installation be completed by a
non-qualified person any product guarantee maybe considered
invalid. For a claim made under our warranty written certification
of your installers qualifications can be required.
It is advised that all doors and drawers are removed prior to
fitting to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
flat to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care always.
Please note that some units are heavy. Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Warning! ! Please check for any hidden pipes or electrical cables
before drilling holes in the floor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Do not over tighten tap or waste fittings, doing so may result in
damaging the basin.
The vanity units CAN ONLY BE installed using the fitting brackets
supplied. Before installing a wooden bathroom product into a new
property, extension or recently plastered room we strongly advise
the building/room is completely dry, well ventilated and adequately
heated prior to installation.
Care & Cleaning.
NEVER use products containing bleach, cleaners of a gritty or
abrasive nature or so called “glass and mirror” cleaning products.
Use a well wrung chamois leather or microfiber cloth for furniture
carcasses.
Ceramic fine fire clay wash basins should only be cleaned with a
mild detergent or warm soapy water; in hard water areas a good
quality limescale remover can be applied.
If any maintenance is required, then it must be carried out by a
qualified Plumber.
1
ZI1211SCW_LH
ZI1211SCW_RH
22.45kgs
ZI1200D
60kgs
x4
600 Two Drawer Basin Unit & Basin 700 Two Drawer Basin Unit & Basin
ZI0611SCW
13.8kgs
ZI600D
40kgs ZI7000D
45kgs
x4 x4
ZI0711CW
15.8kgs

2
Zion Floor Standing Furniture
INSTALLATION INSTRUCTIONS
Two Drawers Basin Unit & Basin Installation - 600-700-1200 Basin Unit
Step 1
Step 3
Step 4
Step 2
860mm -
870mm
Remove the drawers
Remove the drawer before installation.
‘Wall bracket’ installation
a: Place the unit on the furniture site
b: Mark the bracket fixing holes onto the wall. Drill Ø 8mm
holes, insert the wall plugs supplied on solid walls, use
suitable wall fixings for dry-wall (not supplied).
Important: If the basin unit and/or basin are not fitted level
this may result in the basin not draining correctly.
Height Adjustment
When the furniture is fixed to the wall, it can be adjusted if
necessary.
a: To adjust the furniture, turn the adjustment screws, located
on the bottom of the furniture, until the furniture is completely
straight.
Plan unit position: Basin
Decide on the position of the unit.
Pull out the drawer to its full extension,
gently squeeze the locking levers
outwards on both sides and pull the
drawer off the runners at the front.

3
Zion Floor Standing Furniture
Step 5
Step 6
Basin Installation
a: Attach the tap to basin and
carefully bed in the waste using
silicone only.
b: Carefully apply silicone to the
top edges of the unit.
Inserting the drawer:
Place the drawer on the
extended slides.
Push the drawer fully home.
Drawer engages automatically!
Note: Basin waste and taps fittings when over tightened can
create stress within the basin material which may in time
cause the failure of the product. Waste fittings should be
carefully bedded in silicone and the back-nut hang tightened
a
b
c
c: Carefully position the basin
down onto the unit, ensure it is
centrally positioned and flush
at the back.
Connect the tap and waste.
Apply silicone to the join
between the basin and wall and
down sides of the unit.
Leave silicone, 24 hours to dry.
an additional quarter turn using a suitable spanner is sufficient to
create the required water light seal. Care should also be taken
when fitting brassware to tap platforms in order to prevent similar
stress related failures.

For any further information please contact
Crosswater on: 0345 873 8840
Or visit our web-site at:
www.crosswater.co.uk
The manufacturer reserves the right to make technical
modifications without prior notice.
RUNNER ADJUSTMENTS
Step 1
Step 2
Step 3
Front tilt adjustment
Move the green tab until
the front tilt is adjusted.
Side adjustment
Turn the green wheel up
to adjust right and down
to adjust left.
Depth adjustment
Turn the green wheel down
until the depth is adjusted.