Crow Sh-mag-shock-8f User manual

SH-MAG-SHOCK-8F/9F

TWO WAY WIRELESS

MAGNETIC DOOR/WINDOW CONTACT

& SHOCK DETECTOR

PRODUCT FEATURES

DETECTOR OPENING

CIRCUIT LAYOUT

The SH-MAG provide perimeter protection for premises with

early warning upon attempted intrusion.

SH-MAG & SHOCK device analyzes shocks while ignoring

background vibrations. It can be configured Over-The-Air and

feature a 5 year battery life.

•Freewave2™ Two Way ISM

•GFSK with 5 frequencies & LBT

•Immunity to attenuation feature

•Powered by 1 Lithium batteries 3.0V Size CR123

•Contact Open/Close transmission

•Shock detection transmission

•Tamper Open/Close transmission

•Battery life up to 5 years

•Operating Frequencies: 868MHz or 916MHz

•Event Transmission:

Alarm

Tamper Open/Close

Supervision

Battery status

•Bi-Color LED indications

•Up to 500m transmission range in open space

•Remotely configurable

Figure 1

Pull out the detector cover

Figure 2

Remove the batteries cover

INSTRUCTION MANUAL

P/N 7101689_C

BATTERY INSERTION

DETECTOR MOUNTING

LEARNING PROCESS

Figure 3

Batteries can be replaced by the user

Battery type: Lithium. 3V Type: CR123A Size: 2/3AA

Figure 4

Place the Magnet unit near this marking

Figure 5

Basic installation at 10mm between FW2-Mag and Magnet Unit.

Configurations Axis Removal Distance

(mm)

Approach Distance

(mm)

Wood

X 15 12

Y 20 17

Z 35 260

Iron

X 10 5

Z 32 28

For pairing process, please refer to your control panel

instructions.

To pair your device with Shepherd™panel, please proceed

as follows:

1. Enter in installing mode via the "Installer Webpage"

2. Go to "Zones" and select the zone # you want to learn

1. Add Zone -(Reminder: insert Link Type “ISM” , device’s

ID, Device Type “Magnetic & vibration sensor”.)

2. Set the detector configuration: supervision time, VIB

sensitivity, and save configuration.

3. Place a battery as instructed in Figure 3 and wait until

the Red / Green LED stops blinking.

4. The device should register to the Control Panel.

5. When registration process is successfully completed, the

Green LED will constantly light ON for 3 seconds and

then turn OFF.

6. If Green LED continues flashing more than 5 minutes

and stopped, please check MAG-SHOCK settings

details, remove battery and repeat steps 3,4,5.

7. If Led flashes green constantly , please check if device’s

ID is correct or missing.

DETECTOR TESTING

BATTERY REPLACEMENT

SPECIFICATION

STANDARDS APPROVALS

Transmission Test

Go to OVERVIEW level in installer webpage programming

mode, Identify and locate the tested Zone.

Physically Remove the magnet from the sensor, the open alarm

appears in STATE column, return the magnet back and verify

ready state.

Note: refresh the web page display in case you don’t see the

change

Tamper Transmission Test

Pressing and releasing the tamper (push button) enables the

TAMPER transmission test feature.

Use the overview level as above for Transmission Test

Figure 5

CAUTION

RISK OF EXPLOSION

IF BATTERY IS REPLACED BY DIFFERENT TYPE / MODEL.

DISPOSE USED BATTERY

ACCORDING TO ITS INSTRUCTIONS

Shock sensitivity levels Select by EN standards

The detector has 5 adjustable shock sensitivity levels (0

to 4).

The glass window surface EN approved for Sensitivity

Level 0 (Lowest sensitivity level).

The Wooden plate surface EN approved for Sensitivity

Level 3.

The Concrete plate surface EN approved for Sensitivity

Level 4 (Highest sensitivity level).

Detection Method Magnetic Field Sensor

Communication

Protocol

Freewave2™ Two Way ISM

GFSK with 5 frequencies & LBT

Operating

Frequencies

868-869MHz / 916-917MHz

Identification

Unique ID serial number – 24 bit

Events Transmission

Alarm, Tamper, Supervision,

Low Bat, Keep Alive.

Supervision Time

7 min by default

(configurable between 1 to 30 min)

Transmission Range

500m in open space

Battery

Lithium. 3V Type: CR123A

Size: 2/3AA

Battery life

Up to 5 years

Current

Consumptions

Standby ~5 µA

Receive mode ~24 mA

Transmit mode ~50 mA

Transmit power < 14dBm

Low Bat 2.5V

Cut Off 2.3V

Tamper Switch Front Cover Removal

Operating

temperature

-10°C to +55°C

Dimensions

100mm x 23mm x 22mm

Weight (incl. battery) 50gr.

The SH-MAG conforms to the essential requirements set

out by:

•RED directive:2014/53/EU

•EMC directive: 2014/30/EU

•Low Voltage directive: 2014/35/EU

Harmonized Standards applicable to this products are:

•EN300220-2

•EN300220-1

•EN301489-3

•EN301489-1

•EN50130-4

•EN61000-6-3

•EN62368-1

Additional Standards and Directives applicable to this

product are:

•RoHS directive: (EU) 2015/816

•EN50131-2-6

•EN50131-2-8

•EN50131-1

•EN50131-6

•EN50130-5

•EN50131-5-3

Certification body: Telefication B.V.

Security Grade 2, Environmental Class II

Power supply Type C

EVENT TRANSMISSION

SUPERVISION – A periodical transmission (configurable)

indicating detector’s presence.

ALARM – Alarm transmission triggered by the device indicating

opening or shock detection. The Red LED will blink once.

LOW BAT – Whenever the battery reaches the low level

(2.5V), a Battery Low signal will be sent. When Battery level

drops below Cut Off level (2.3V) the device will stop functioning

and the Red LED will blink for 10 seconds and then turned Off.

TAMPER – Whenever the cover is removed from the device or

the device is tear off from the wall, a message will be

transmitted with “Tamper ON” signal. When cover will be

returned a “Tamper OFF” signal will be transmitted.

WARRANTY POLICY CERTIFICATE

[email protected]

support@crow.co.il

www.thecrowgroup.com

These instructions supersede all previous issues in circulation prior to April 2019

Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the last day of the

week and year whose numbers are printed on the printed circuit board inside these products.

Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's procedures, as such

procedures are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective in materials or workmanship under

normal use and service. Repaired products shall be warranted for the remainder of the original Warranty Period.

All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall be borne solely by

the Purchaser.

This Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the products (or any part thereof) by anyone

other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product which Crow did not provide; (d) failure caused by software

or hardware which Crow did not provide; (e) use or storage other than in accordance with Crow’s specified operating and storage instructions.

There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend beyond the description

on the face hereof.

This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the Purchaser in connection

with the products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate replaces all other warranties and liabilities, whether

oral, written, (non-mandatory) statutory, contractual, in tort or otherwise.

In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by negligence of the Crow or

any third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever.

Crow does not represent that these products cannot be compromised or circumvented; that these products will prevent any person injury or property loss or damage by

burglary, robbery, fire or otherwise; or that these products will in all cases provide adequate warning or protection.

Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events occurring without

providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result.

Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to give any warning.

If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s maximum liability shall