Crow Sh-sirint-9f User manual

SH-SIRINT-8F/9F

WIRELESS

INDOOR SOUNDER

PRODUCT FEATURES

PRODUCT OVERVIEW

DEVICE OPENING

The SH-SIRINT is an advanced slim designed wireless

indoor sounder that extends the sound of your alarm inside

your premises.

The SH-SIRINT is ideal for residential and light commercial

buildings, particularly where outdoor sirens are prohibited.

•ISM Radio 2GFSK

•Ultra Low current consumption

•Powered by 2 Lithium batteries Type AA 1.5V

•Wall Tamper protection

•Battery life up to 5 years

•Operating Frequencies: 868-869MHz / 916-917MHz

•Event Transmission:

•Alarm

•Tamper Open/Close

•Supervision

•Battery status

•Bi-Color LED indications

•Up to 500m transmission range in open space

•Remotely configurable

•Selectable Dipswitches for working with panel types :

Shepherd, Serenity, Runner.

Figure 1

1. Push the latch located on the bracket

2. Slide Up the unit device

INSTRUCTION MANUAL

P/N 7105411 REV. C

WALL MOUNTING

BATTERIES INSERTION

DIPSWITCHS

PAIRING PROCESS

Figure 2

Use supplied screw to mount the bracket on the wall

Check that the base is flat against the wall to facilitate the unit

device insertion into the wall

bracket

Figure 3

Batteries can be replaced by the user

Please refer to section "Battery Replacement" for this

operation.

Dipswitch Setting

The table describes the different settings for

SHEPHERD, SERENITY, RUNNER panel types.

Note (for Shepherd default): The Alert sound time is 3

minutes and The Alert flasher time is 30 minutes.

Activation time can be changed from Outputs level (see

installation manual)

Note: Any change in the DIP switches requires

battery removal and reinsert

Dipswitch

Number

Shepherd

Serenity/Runner

OFF -

Serenity / Runner

N/A

ARM

DISARM

Battery

Flashes

flashes

Low

battery

3+3

flashes

Flashes

N/A

ARM

DISARM

Battery

Beeps

1 Beep

Low

battery

3+3

Beeps

2 Beep

N/A

Flasher and Buzzer timeout is 15 min

dipswitch is OFF timeout is 2 min.

For pairing process, please refer to your control panel

instructions.

To pair your sounder(for Shepherd panel),please proceed

as follows:

1. Enter in installing mode via the” installer Webpage”..

2. Go to Outputs and select the output # you want to learn.

3. Add Output – (insert link type “ISM” Device’s ID, Device

type “smart siren”.

4. Set Siren Configuration output, and save configuration.

5. Place the 2 batteries as instructed in figure 3 and wait

until the red/green LED stops blinking.

6. The device should register to the Control Panel.

7. When registration process is successfully completed,

the Green LED will constantly light ON for 3 seconds and

then turn OFF.

8. If Green LED continues flashing more than 5 minutes

and stopped. Please check siren settings details,

remove batteries and repeat step 5,6,7.

Pairing sounder for SERENITY/RUNNER panels

1. Enter in installing program mode

2. Go to panel learning mode, and press the enter key

to start the learning process,

3. Place the battery as instructed in figure 4.

4. the FW2-NEPTUNE RED/Green LED alternately

blinks and wait until sounder power up and learning

process end.

5. When registration process is successfully

completed, the Green LED will constantly light ON

for 3 seconds and then turn OFF.

If Registration failed, the Red LED will blink, remove the

battery, wait few seconds, and repeat the learning process.

1. Slide down the unit device

into the bracket

2. Reset tamper alarm on

the control panel

TESTING THE DEVICE

BATTERY REPLACEMENT

SPECIFICATION

STANDARDS APPROVALS

After the pairing is completed verify that the sounder is working

properly:

•Perform Arm/Disarm verify Beep/Led indications.

•Perform an Alarm; verify Piezo and LED is activated.

•Perform Alarm Reset by User pin code.

Figure 6

CAUTION

RISK OF EXPLOSION

IF BATTERY IS REPLACED BY DIFFERENT TYPE / MODEL.

DISPOSE USED BATTERY

ACCORDING TO ITS INSTRUCTIONS

AFTER REPLACING BATTERIES…

•Slide down the sounder device into the bracket as

illustrated in figure 4

•Perform Tamper reset on your control panel

•Proceed with device testing to check proper functioning

Alert Method Internal Piezo and LED

Sound Level More than 100dB (at 1 meter)

Flash Light

Red/Green and White

LED indications

ISM Radio 2GFSK

Operating

Frequencies 868-869MHz / 916-917MHz

Identification Unique ID serial number – 24 bit

Events Transmission

Alarm, Tamper, Supervision,

Low Bat.

Supervision Time 7 min by default

Transmission Range 500m in open space

Battery

2 Lithium batteries 1.5V

AA Type

Battery life Up to 5 years

Current

Consumptions

Standby ~60 µA

Receive mode ~26 mA

Transmit mode ~50 mA

Transmit power <14dBm

Low Bat 2.9V

Cut Off 2.5V

Tamper Switch Bracket Removal

Operating

temperature

-10°C to +55°C

Dimensions 92.5mm x 26mm

Weight (incl. battery) 80gr.

The SH-SIRINT conforms to the essential requirements

set out by:

•RED directive:2014/53/EU

•EMC directive: 2014/30/EU

•Low Voltage directive: 2014/35/EU

Harmonized Standards applicable to this products are:

•EN300220-2

•EN300220-1

•EN301489-3

•EN301489-1

•EN50130-4

•EN61000-6-3

•EN60950-1

•EN50130-5

•EN50131-5-3

Additional Standards and Directives applicable to this

product are:

•RoHS directive: 2002/95/EC

•EN50131-4

Security Grade2, Environmental Class II

Power supply Type W

Certification body: Telefication B.V.

EVENT TRANSMISSION

SUPERVISION

A periodical transmission indicating detector’s presence.

ALARM

Siren sound from the device indicating alarm in progress. The

white LED blinking during the operation.

LOW BATTERY

Whenever batteries reach the low level (2.9V), a Battery Low

signal will be sent. When Battery level drops below Cut Off level

(2.5V) the device will stop functioning and the Red LED will blink

for 10 seconds and then turned Off.

TAMPER

Whenever the device is removed from the bracket, a message

will be transmitted with “Tamper ON” signal. When cover will be

returned a “Tamper OFF” signal will be transmitted.

You should reset this tamper alarm on your control panel.

WARRANTY POLICY CERTIFICATE

sales@crow.co.il

[email protected]

www.thecrowgroup.com

These instructions supersede all previous issues in circulation prior to December 2017

Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the last day of the

week and year whose numbers are printed on the printed circuit board inside these products.

Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's procedures, as such

procedures are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective in materials or workmanship under

normal use and service. Repaired products shall be warranted for the remainder of the original Warranty Period.

All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall be borne solely

by the Purchaser.

This Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the products (or any part thereof) by anyone

other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product which Crow did not provide; (d) failure caused by software

or hardware which Crow did not provide; (e) use or storage other than in accordance with Crow’s specified operating and storage instructions.

There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend beyond the description

on the face hereof.

This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the Purchaser in connection

with the products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate replaces all other warranties and liabilities,

whether oral, written, (non-mandatory) statutory, contractual, in tort or otherwise.

In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by negligence of the Crow

or any third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever.

Crow does not represent that these products can not be compromised or circumvented; that these products will prevent any person injury or property loss or damage

by burglary, robbery, fire or otherwise; or that these products will in all cases provide adequate warning or protection.

Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events occurring without

providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result.

Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to give any warning.

If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s maximum liability