Crow Swan quad User manual

INSTALLATION INSTRUCTIONS

SWAN QUAD

PIR MOTION DETECTOR With PET IMMUNITY up to 25 kg

PRODUCT FEATURES

The SWAN QUAD detector uses a special

designed optical Lens with unique Quad (Four

element) PIR Sensor and new ASIC based

electronics optimized to eliminate false alarms,

caused by small animals and Pets.

The SWAN QUAD provides unprecedented levels

of immunity against visible light.

The Detector offers an exceptional level of

detection capability and stability for every

security installation.

The SWAN QUAD is supplied with a Wide Angle

lens.

•Quad Linear Imaging Technology for sharp

analysis of body dimensions and

differentiation from background and animals.

•ASIC based electronics.

•Immunity to animals up to 25kg.

•18m Detection Range with Wide Angle Lens.

•Temperature compensation.

•Compact Design for Residential Installation.

•Variable pulse width adjustment.

•Sensitivity adjustment.

•Environmental immunity.

•Height installation calibration free

(1.8m – 2.4m).

•LED Remote function.

SELECT MOUNTING LOCATION

Choose a location most likely to intercept an intruder.

(Our recommendation is a corner installation). See

detection pattern fig.3. The quad-element high quality

sensor detects motion crossing the beam; it is slightly

less sensitive detecting motion toward the detector.

The SWAN quad performs best when provided with a

constant and stable environment and background.

AVOID THE FOLLOWING LOCATIONS

•Facing direct sunlight.

•Facing areas that may change temperature

rapidly.

•Areas where there are air ducts or substantial

airflows.

WIRE SIZE REQUIREMENTS

Use #22 AWG (0.5 mm) or wires with a larger

diameter. Use the following table to determine the

required wire gauge (diameter) depending on the

length of wire between the detector and the control

panel.

Wire Length m 200 300 400 800

Wire Diameter mm .5 .75 1.0 1.5

Wire Length ft. 800 1200 2000 3400

Wire Gauge # 22 20 18 16

DETECTOR INSTALLATION

The detector can either be wall or corner mounted.

If ceiling or special wall mounting is required, use the

optional bracket base. Refer to bracket description.

(See fig. 6).

1.To remove the front cover, unscrew the holding screw

and gently raise the front cover.

Fig.1

2. To remove the PC board, carefully unscrew the

holding screw located on the PC board.

3. Break out the desired holes for proper installation.

Fig.2

4.The circular and rectangular indentations at the

bottom base are the knockout holes for wire entry.

You may also use mounting holes that are not in

use for running the wiring into the detector. (For

Bracket option - lead wire through the bracket)

5.Mount the detector base to the wall, corner or ceiling.

(For bracket installation option see fig. 6).

6.Reinstall the PC board by fully tightening the holding

screw. Connect wire to terminal block.

7.Replace the cover by inserting it back in the

appropriate closing pins and screw in the holding

screw.

DETECTOR CONNECTION

Terminal 1 - Marked “ - ” (GND)

Connect to the negative Voltage Supply or ground of

the control panel.

Terminal 2 - Marked “ + ” (+12V)

Connect to a positive Voltage Supply of 8.2 -16Vdc

source (usually from the alarm control unit)

Terminals 3 & 6 - Marked “ EOL ” – End of line

option.

Terminals 4 & 5 - Marked “ TAMPER ”

If a Tamper function is required connect these

terminals to a 24-hour normally closed protective zone

in the control unit. If the front cover of the detector is

opened, an immediate alarm signal will be sent to the

control unit.

Terminals 7 & 8 - Marked “RELAY ”

These are the output relay contacts of the detector.

Connect to a normally closed zone in the control

panel.

TESTING THE DETECTOR

Wait one minute after applying 12 Vdc power for warm

up time. Conduct testing with the protected area

cleared of all people.

Walk test

1. Remove front cover.

2. Set LED to ON position.

3. Reassemble the front cover.

4. Start walking slowly across the detection zone.

5. Observe that the LED lights whenever motion is

detected.

6. Allow 5 sec. between each test for the detector to

stabilize.

7. After the walk test is completed, you can set the

LED to OFF position.

NOTE:

Walk tests should be conducted, at least once a year,

to confirm proper operation and coverage of the

detector.

Fig.3

Fig.4

7101570_D.doc - 1 -

Holding screw

A. Wire access holes

B. Use for flat wall

mounting

C. Corner mounting -

use all 4 holes.

Sharp left or right

angle mounting -

use 2 holes (top

and bottom)

D. For bracket

mounting

A A

INSTALLATION INSTRUCTIONS

SWAN QUAD

PIR MOTION DETECTOR With PET IMMUNITY up to 25 kg

SETTING UP THE DETECTOR

PET IMMUNITYJUMPER SETTING

This jumper is used for setting the PET Immune

function - up to 15kg or 25kg, depending on the pet

size.

PULSE WIDTH JUMPER SETTING

This jumper is used for setting the PULSE count

function in order to provide PIR sensitivity control

according to the environment.

LED ENABLE JUMPER SETTING

This jumper is used for setting - LED Enable / Disable.

Note: The LED Switch does not affect the operation of

the relay.

When an intrusion is detected, the LED will activate

and the alarm relay will switch into alarm condition for

2 sec.

PIR SENSITIVITY ADJUSTMENT

Use the Potentiometer marked “SENS” to adjust the

detection sensitivity between 15% and 100%,

according to walk test in the protected area.

(Factory set to 57%)

Rotate the potentiometer clockwise to increase range,

counter-clockwise to decrease range.

Fig.5

BRACKET INSTALLATION OPTION

Ceiling bracket base Wall bracket base

Fig. 6

TECHNICAL SPECIFICATION

MODEL SWAN QUAD

Detection Method Quad (Four element) PIR

Power Input 8.2 to 16 VDC

Current Draw Standby: 8mA (±5%)

Active: 10mA (±5%)

Temperature

Compensation YES

Pulse Width Adjustable

Alarm Period 2 sec (±0.5sec)

Alarm Output N.C 28VDC 0.1 A with

27Ohm series protection

resistor

Tamper Switch N.C 28VDC 0.1A with

10 Ohm series protection

resistor - open when

cover is removed

Warm Up Period 60sec (±5sec)

LED Indicator LED is ON during alarm

Operating Temperature -20

C to +60

RFI Protection 30V/m 10 - 1000MHz

EMI Protection 50,000V of electrical

interference from lightning

or power through

Dimensions 92mm x 59mm x 37mm

Weight 40gr

CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE

This Warranty Certificate is given in favor of the purchaser (hereunder the "Purchaser") purchasing the products directly from Crow or from its authorized distributor.

Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the last day of the week and

year whose numbers are printed on the printed circuit board inside these products (hereunder the "Warranty Period").

Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its solediscretion and subject to Crow's procedures, as such procedures

are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective in materials or workmanship under normal use and service.

Repaired products shall be warranted for the remainder of the original Warranty Period.

All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall be borne solely by the

Purchaser.

Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the products (or any part thereof)

by anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product which Crow did not provide; (d) failure caused by

software or hardware which Crow did not provide; (e) use or storage other than in accordance with Crow’s specified operating and storage instructions.

There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend beyond the description on the

face hereof.

This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the Purchaser in connection with the

products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate replaces all other warranties and liabilities, whether oral, written,

(non-mandatory) statutory, contractual, in tort or otherwise.

In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by negligence of the Crow or any

third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Crow does not represent that these

products can not be compromised or circumvented; that these products will prevent any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that

these products will in all cases provide adequate warning or protection.

Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events occurring without providing

an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result.

Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to give any warning.

If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s maximum liability shall not in