Crye Precision LVS User manual

LVS™SIDE PANEL SETS OPERATOR’S MANUAL

This manual must be carefully read by all persons who have or will have
the
responsibility for using or maintaining this product.
Any warranties made by Crye Precision LLC with respect to this product are voided if the
product is not used and maintained in accordance with the instructions in this
manual.
For any questions relative to the use or repair of this product, please write Crye Precision
LLC or call 1-718-246-3838 during regular business hours.
The following are safety warnings intended to call attention to fundamental performance
limitations and areas of the product where proper usage must be followed. Failure to use and maintain
the product according to the warnings contained herein may result in the product failing to
perform as designed, and/or the persons relying on this product sustaining serious personal injury
and/or death.
• Ballistic components are designed to
protect the wearer only against the ballistic
threat level stated in the Product manual.
They are not intended to protect against
rifle fire or sharp edged or pointed
instruments unless specified on the inserts.
•Ballistic components are not intended to protect
the wearer from projectiles that hit less than 1
inch from any edge of the ballistic insert.
•Exposure of the internal materials to water,
chemicals, or sunlight will reduce the
effectiveness of the ballistic insert.
•Perform periodic inspections of the armor.
Discontinue use of damaged ballistic inserts
immediately.
•Ballistic inserts are not flame resistant.
•Ballistic inserts that show no signs of damage
must be replaced 5 years from date of purchase.
•DO NOT machine wash or dry clean the
product. Exposure to detergents, bleach, or
solvents may result in degradation and reduce
the effectiveness of the product.
•Inspect the product for discoloration, cuts,
tears, abrasions or cracks before and after each
use.
•DO NOT alter the product in any way.
•DO NOT expose the product to open flame or
excessive heat.
•All replacement parts must be acquired from
Crye Precision LLC or alicensed distributor.
•The most current version of this manual may be
found at www.cryeprecision.com.
•DO NOT use this product except in itsintended
manner.

EQUIPMENT INFORMATION
INTRODUCTION................................................................ 1
INCLUDED COMPONENTS.................................................1
CONFIGURING THE LVS™ SIDE PANEL SETS
OPTIONAL SIDE ARMOR ...................................................... 3
CARE INSTRUCTIONS......................................................................... 5
CONTENTS

1LVS™ SIDE PANEL SETS
INCLUDED COMPONENTS
INTRODUCTION
The LVS™ 6X6 SIDE PANEL SET, and LVS™ 6X9 SIDE PANEL SET add 6 and 9 more inches of ballistic coverage to the side of the LVS™ VEST,
respectively. Wear with the LVS™ BASE VEST or insert into a SIDE ARMOR CARRIER for use with any of the various LVS COVERS. Made in the US
from US materials.
1LVS™ SIDE PANEL SETS
1

CONFIGURING THE LVS™SIDE PANEL SETS

3LVS™ SIDE PANEL SETS
OPTIONAL SIDE ARMOR
To congure the LVS™ SIDE PANEL SETS, do the following:
1
2
To attach side armor, slide the straps through the appropriate slots
on the side armor.
If more overlap is desired the front or rear slot on the side armor
can be skipped. Side armor should overlap UNDER the FRONT
vest panel and OVER the REAR panel.

4CONFIGURING THE LVS™ SIDE PANEL SETS
Completed conguration.
3

5LVS™ SIDE PANEL SETS
CARE INSTRUCTIONS
Care instructions must be read prior to each use.
Do not machine wash or dry. Remove dirt by using a cloth or soft brush. Hand wash with warm water and cloth or soft brush. Air dry
indoors or in shade.

6NOTES
NOTES

ABOUT US
Crye Precision designs and manufactures
truly innovative equipment for America’s
ghting forces. We are proud and honored
to serve our customers' needs. We spend
as much time as we can with users,
continuously incorporating their experience
and feedback into the gear. We give them
our full support and are indebted to them
for their service and their sacrice. We make
uncompromising gear for uncompromising
individuals. We work hard to provide smart,
high-performance, long-wearing gear for
people who demand the best. We make
all of our gear in America from American
materials. Every item is designed to help
you perform better.
WARRANTY
If a defect in materials or workmanship is
found in any of our products, we will repair
or replace it, free of charge, for the lifetime
of the product. This excludes normal wear
and tear. Be aware that the customer is
responsible for any and all return shipping
charges. This applies to the original purchaser
and is nontransferable.
BODY ARMOR
It is against Federal Law for a person
convicted of a violent felony to purchase
or possess body armor. In addition, various
states also have laws restricting the purchase
or possession of body armor by persons
convicted of certain felonies, other crimes
of violence, or drug crimes. By purchasing
body armor, you acknowledge and certify
that (i) you have no felony convictions, (ii)
you have not been convicted of any other
crime that would restrict your ability to
purchase or possess body armor under any
Federal or State law, (iii) you do not intend
to use the body armor for any criminal
purpose and (iv) you are over 18 years old.
Crye Precision reserves the right, in its sole
discretion, to refuse to sell body armor
to any person. Additionally, the sale of
body armor to residents of Connecticut is
restricted to in-person sales, unless the
sale is made to certain law enforcement
or military personnel. We require that all
orders of body armor be accompanied by
a government issued photo identication.
CONTACT INFO
Crye Precision LLC
Brooklyn Navy Yard
63 Flushing Ave Unit 252
Building 128B
Brooklyn, NY 11205
Phone: [phone]
Fax: [phone]
[email protected]
www.cryeprecision.com
COPYRIGHT
© 2019 Crye Precision LLC. The ‘CP’ logo
are trademarks of Crye Precision LLC.
REV 080219

LVSSAX