Crystal Mountain K2 User manual

K2
Water Dispenser User Manual

1. LED Indicator Lights
Cold LED ( – On when cooler is connected to power)Blue
Cook / Hot LED ( / – – C&C Model or Hot Tank Switch in OFF position – Green GREENRed
RED – Hot Tank Switch is ON)
CrystalFlo LED (Yellow – Flash when CrystalFlo timer reaches set point) – light not activated
for any other function
2. Light sensor (Activates Power save function when room lights are turned off)
3. Cold Water Lever – Depress lever to dispense water. Release lever to stop.
4. Hot/Cook Water Lever
Hot Water Lever (with Child Resistant Safety Feature) – Pinch the lever upwards, and RED
depress faucet lever to dispense water. Release lever to stop.
Cook Water Lever – Depress lever to dispense water. Release lever to stop.
5. Dispense Area Lighting
Nightlight ( – On when cooler is connected to power)Blue
Pour Area Light (White – on during water dispense)
6. Drip Tray – Dishwasher Safe. Snaps in and out. Position glass or cup over center to avoid
spills.
7. Cup Dispenser – Integrated spring loaded cup dispenser (9oz flat bottom)
8. Hot Water Activation Switch – Located on the back of product near the top right corner (when
viewed from rear of product)
9. Water Outlet – Hot (or Ambient) and Cold water is dispensed from this location
FEATURES
LED Indicator Lights
Cold LED
Cook / Hot LED
CrystalFlo LED
CrystalFlo Water Cartridge
12
3
4
5
6
8
9
7
Product may not appear exactly as shown

Receiving
Inspect the cooler box immediately and carefully for any evidence of shipping or handling damage before
signing to receive goods. In case of shipping damages, claims should be filed immediately with the carrier.
Please note that the carrier will not accept claims for any damage discovered after signing for
UNINSPECTED GOODS.
Ensure the cooler stands upright for 24 hours before plugging it in.
Install Base Plate
1. Stand cooler upright on flat, smooth floor.
2. Align side plate with base (Figure 1), and slide into base to locked position (Figure 2).
3. Repeat for opposite side (Figure 3), (Figure 4).
Locate Water Dispenser
1. Place the water cooler indoors, on a flat level surface in a cool shaded location near a grounded wall
outlet.
2. Position water dispenser so that the back of the unit is a minimum of 4 inches / 10 cm away from the wall
to ensure proper ventilation (Figure 5).
3. Install a bottle of water on the top of the water cooler (Figure 6).
Note: To prevent water leaks, a NON-SPILL Bottle Cap MUST be installed on the bottle (Figure 7).
4. Ensure that the hot water switch near the top of the rear panel is turned off. (Figure 8).
THANK YOU FOR BUYING A CRYSTAL MOUNTAIN WATER COOLER!
GETTING STARTED
Figure 1 Figure 2 Figure 3 Figure 4
Figure 5 Figure 6 Figure 7 Figure 8
4 inches (10cm)

Provide Electricity
Ensure that the available power supply matches the cooler’s voltage specifications indicated on the
nameplate label (located at the top/rear of unit).
Plug power supply cord into receptacle.
Please ensure that cooler is set up so as access to the power outlet and plug is unobstructed.
Note: To provide additional protection from the risk of shock, this unit MUST be connected to a ground
fault circuit interrupter (GFCI) outlet at all times. Use of an extension cord will void any warranties.
Prime Water System (Required during initial setup and after replacement of
CrystalFlo Water Cartridge)
Depress the water lever to fill the hot tank. Hot
When water begins to flow from the hot outlet the tank is full (approx. 1 minute)
The Cold water tank will fill automatically (approx. 3 minutes)
Activate Heating Function (H&C Model Only)
Ensure Priming of Hot water system is complete before starting this step
Notice: Hot (Heated) water will not be dispensed by the cooler until the hot
switch has been activated (located at the top/rear of unit).
Turn on the hot water switch
- To disable the heating function (Hot Water), turn off the hot water switch
(Figure 9)
DO NOT draw water from the cooler for about 30 minutes to let the water cool or
heat.
Optimum water temperatures will be reached after several hours of operation.
DISPENSING WATER
The CrystalFlo Water Cartridge has been tested and sanitized prior to packaging. During transit dust
and odors may accumulate in the water tanks and lines. Dispense and dispose of at least 1 quart (1
Liter) of water prior to drinking any water.
Cold Water Dispensing
The temperature control of the cold water is preset to dispense water between
37-50°F (3 to 10°C)
Optimum cold water temperatures will be reached after 1-2 hours of operation.
During this time the compressor could run continuously. This is normal.
1. Position bottle, glass or other container below water outlet
2. Depress (push downwards) cold water lever to start cold water flow
(Figure 10)
3. Release cold water lever once desired fill level is achieved
Hot Water Dispensing
The temperature control of the hot water is preset to dispense water between 169-203°F (76 to 95°C)
CAUTION
This unit dispenses water at temperatures that can cause severe burns.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Figure 9
Figure 10

Optimum hot water temperatures will be reached after 20-30 minutes
1. Position bottle, glass or other container below water outlet
2. Push the lever upwards (Figure 11), (Figure 12), and depress faucet lever to dispense water RED
(Figure 13)
3. Release hot water lever once desired fill level is achieved
CLEANING
Do not immerse the unit in water for cleaning.
External: Disconnect power supply cord (Figure 14), use only mild dishwashing liquid or cleaning
products and a soft cloth for cleaning the exterior surfaces (Figure 15). DO NOT use bleach or abrasive
cleaners. Use a vacuum cleaner to remove dirt and lint from the condenser (Figure 16). The unit should
be cleaned every 3 months, except where fingers touch the temperature selectors, which can be wiped
often with hygienic wipes or mild cleaning products.
Caution: Do not clean unit with pressure washer.
Ensure the following when cooler is to be serviced:
Turn off the hot water switch and disconnect power supply cord (Figure 17) .
Replacement of CrystalFlo Water Cartridge
A flashing yellow light above the faucet levers will alert you to when the CrystalFlo Water Cartridge
should be replaced. The system has been pre-set to provide indication after a period of 12 months of
use. User may operate the cooler as normal until the bottle has been emptied. It is also advised to
replace the CrystalFlo cartridge if there is a leak from the cartridge, taste problem or
discoloration to the water.
1. Place a glass or other container below the water outlets (to catch drips)(Figure 18), and unlatch the
Top Cover Locking Clip (located inside of the Bottle Installation area)(Figure 19), and open Top
Cover (Figure 20).
2. Pull CrystalFlo Water Cartridge upwards to remove (Figure 21) . Do not squeeze the water reservoir
as water could leak out. In addition, it may be helpful to have a bucket nearby to place the used
CrystalFlo in.
Figure 11 Figure 12 Figure 13
Figure 18 Figure 19 Figure 20 Figure 21
Figure 14 Figure 15 Figure 16 Figure 17

3. Please recycle the CrystalFlo whenever possible, otherwise dispose of responsibly
4. Ensure seal is properly installed on the Inlet/Outlet tube of the CrystalFlo Water Cartridge assembly
(may have shifted during shipment or un-packaging)
5. Align CrystalFlo Water Cartridge with openings in cooler, and push downwards into place (Figure 22).
Ensure that foam seal is pushed down and seals the reservoir completely.
6. Close the top cover (push downwards to lock into place) (Figure 23 and Figure 24). If cover does not
close completely, make sure that CrystalFlo is inserted completely.
7. Install replacement bottle (Figure 25)
8. Prime water system (see section for Prime Water System)
CAUTION! ALWAYS DRAIN WATER COMPLETELY
BEFORE SHIPPING OR STORING THE COOLER!
TROUBLESHOOTING
Water Leaks
• If water dripping from above, first try to replace the water bottle.
• If water leaking (or not bottle related), unplug Dispenser, remove bottle and call 1-800-
878-6422 for assistance
Water Not Dispensing
• Ensure Hot/Cold tanks have been primed
• Ensure that the water selection lever is fully depressed
• Ensure all internal tubing is free of any holes, cuts or cracks.
Not Cooling
• Optimum cold water temperatures will be reached after 1-2 hours of operation
• Ensure that the dispenser is at least 4 inches (10cm) from the wall to provide sufficient
ventilation
• High usage may deplete the cold water reservoir faster than the cooler can cool it
• If the water still isn’t cold, please call 1-800-878-6422 for assistance
No Hot Water
• Optimum hot water temperatures will be reached after 15-20 minutes
• Ensure that the Hot Water Switch (located at the top of the back panel) is turned on
• If the water still isn’t hot, please call 1-800-878-6422 for assistance
Dispenser is Noisy
• Ensure that the dispenser is positioned on a flat, level surface
• Ensure that the bottle is not empty. If empty, replace it
Figure 22 Figure 23 Figure 24 Figure 25

SAFETY PRECAUTIONS
WARNING
To reduce risk of injury and property damage, user must read this entire guide
before assembling, installation and operation of the dispenser.
Failure to follow the instructions in this manual can cause personal injury or
property damage.
This product dispenses water at very high temperatures. Failure to use properly
can cause personal injury.
When operating this dispenser, always exercise basic safety precautions,
including the following:
• Prior to use, this dispenser must be assembled and installed in accordance with this
manual.
• Install indoors on a flat level surface only. Place dispenser in a dry place away from
direct sunlight. Do NOT use outdoors.
• This appliance is intended to be used in household and similar applications such as
- Staff kitchen areas in shops, offices and other working environments;
- Farm houses and by clients in hotels, motels and other residential type
environments;
- Bed and breakfast type environments;
- Catering and similar non-retail applications.
• Do NOT place dispenser into an enclosed space or cabinet.
• This dispenser is intended for dispensing water only. Do NOT use other liquids.
Never use any other liquid in the dispenser other than known and microbiologically
safe bottled water.
• Do not use an extension cord. Use of an extension cord will void any warranties.
• To provide additional protection from the risk of shock, this unit MUST be
connected to a ground fault circuit interrupter (GFCI) outlet at all times.
• If the supply cord is damaged, it must be replaced or assembled with matched power
cord available from the manufacturer or its service agent.
• Always grasp plug and pull straight out from outlet. Never unplug by pulling on
power cord.
• To protect against electric shock, do NOT immerse cord, plug, or any other part of
dispenser in water or other liquids.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Use with caution only.
• Repairs should only be performed by a certified technician. Please contact us at 1-
800-878-6422 for assistance

Services Required:
See nameplate located at the top/rear of the dispenser
The customer acknowledges that water, like other liquids, can cause damage to surfaces.
The customer takes full responsibility for placing the cooler within a residence or
business, and acknowledges that failure to address drips, leaks or spillages is at the
customer’s risk.
The Warranty and Intertek Testing Services (ETL) and CE listings for the coolers are
invalidated if any alteration, modification, or use or misuse in combination with any other
machine or devices is deemed to be the source of any claim. The manufacturer accepts no
liability (including for bodily injury) resulting from any alteration, misuse, neglect,
accidents, improper installations or repairs.
This unit is designed to be used typical residential and office type environments within a
temperature range of 50~96.8°F (10~36°C)
The unit is rated IPX0. (This unit is not protected against ingress of water)
For more information on this product, please visit www.crystalcoolers.com
DOC-C100116 Rev0114