Crystal Mountain STORM Bottom-Load User manual

4 - 1
Install POU Water System
NOTES
Installation should only be executed by properly trained personnel. Check and comply with all national
and local regulations regarding mains water access. The connection must be to the potable mains water
supply and should be via a shut off valve. An appropriate anti-flood device should be fitted as closely as
possible to the mains connection point. In order to satisfy plumbing regulations, a backflow preventer or
check valve maybe required.
Failure to use an appropriate anti-flood device for any reason will not obligate or make Crystal Mountain
responsible in any way for Product Liability issues relating to any claims, including water damage claims.
INSTALLATION INSTRUCTIONS
System requirements
Water inlet pressure:
• Minimum 20 PSI (0.138 MPa)
• Maximum 80 PSI (0.552 MPa)
• Where pressures exceed 80 PSI (0.552 MPa) a Pressure Reducing Valve must be fitted
1. Unpack and rinse:
a. Unpack:
1) Slide the access door upwards to open (Figure 4-1).
2) Unstrap the Velcro belt, remove the POU Kit along with the 2 pcs foam pads and plastic bag (Figure
4-2). (Discard: Strap, Foam Pads and Bag)
b. Rinse:
1) Slide up Reservoir Kit from its frame (Figure 4-3 and 4-4).
Figure 4-1 Figure 4-2
Figure 4-3 Figure 4-4

4 - 2
2） Use latex or nitrile gloves or wash hands before and after handling water contact parts.
Remove cover assembly from the reservoir by pulling upwards (Figure 4-5 and Figure 4-6). Rinse
cover assembly and reservoir with clean water and reassemble prior to installation into the frame
assembly (Figure 4-7 and Figure 4-8).
Note: Ensure siphon tube does not curl upwards when installed, and that the slot in the lid is
aligned with the rib on the reservoir (as shown if Figure 4-8).
3） Install Reservoir Kit onto the frame by sliding Reservoir down into holder (Figure 4-9 and Fig-
ure 4-10), until Reservoir stands on Base (Figure 4-11and Figure 4-12).
2. Filter Kit installation and water line connection:
1）Mount Filter kit onto mounting plate using the accessory screws.
2）Connect the Filters to the POU Assembly. Connect the 1/4 inch water line from the top of
the POU system to the product water outlet connection of the Filter system.
3）Connect 1/4 inch water line from the mains water connection to the filter inlet connection
(not shown) through the tube bushing on condenser (from back) (Figure 4-13~4-17).
Note: Ensure tubing is positioned accordingly to prevent damages (i.e. kink or cut).
Note: In the event a filtration system is not installed, the ¼ inch water line from the mains
water connection can be connected directly to the water line of the POU system (Figure 4-18)
Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8
Figure 4-9 Figure 4-10 Figure 4-11 Figure 4-12
Figure 4-13 Figure 4-14 Figure 4-15 Figure 4-16

4 - 3
3. Install POU system into cooler:
a. Connect the bottle tube (within cooler) to the top of the POU system (Figure 4-19 to 4-21).
b. Verify Indicator Position
Ensure that float indicator is in the GREEN position after installation is complete (Figure 4-22). If
indicator shows RED, slide the lever forward to reset.
Figure 4-17 Figure 4-18
Figure 4-19 Figure 4-20 Figure 4-21
Figure 4-22

4 - 4
c. Position POU system within the cooler, ensuring that the tubing is not kinked or located where it
will interfere with the access door (Figure 4-23).
d. Push downwards to close the access door (Figure 4-24)
4. Open (Turn On) the water supply to the POU system
Allow the holding tank to fill prior to priming the water system on the Storm Water Dispenser. De-
pending on the type of water treatment system installed, this may take several hours.
Instructions for the proper priming of the water system can be located in the Storm Water Dispens-
er instruction booklet.
http://www.crystalcoolers.com/Downloads/InstructionManual/Storm.pdf
Figure 4-24
Figure 4-23