Culligan ClearLink Pro User manual

DRINKING WATER | AGUA POTABLE
ClearLink Pro™
Wireless Filtration Control
Installation and operating instructions
ClearLink Pro™
Control de Filtración de Agua Inalámbrico
Instrucciones de instalación y operación

2
PRECAUTIONS
WARNING: Follow all precautions indicated in the manual provided with the Culligan water treatment system.
WARNING: For systems using a booster or distribution pump, the pressure of the treated water cannot exceed
the pressure of the cold water supply.
CAUTION: Control box must be protected against freezing temperatures, frost, snow, sleet, and ice.
Exposure to these can produce cracks and product failures.
CAUTION: This product has a limited service life. We recommend that a record be kept regarding the
date of install and any other performed maintenance. Because of the product’s limited service life and
to prevent costly repairs or possible water damage, we strongly recommend that the control box be
replaced every ten years.
WARNING: For cold water use only. Do not use on hot water line.

the system be ushed thoroughly. Let the ltered water run for 5–6minutes before using.




4
2




PARTS
INCLUDED:



3/8" x 1/4" Tube Adapter


SPECIFICATIONS
 
Temperature Range: 40–100°°
English

3
UNIVERSAL WIRELESS FILTRATION CONTROL
Remote Button
Button Part No.: 01029450
Trim Ring Part Nos.:
Chrome 01029452
Brushed Nickel 01029453
Oil Rubbed Bronze 01029454
Control Box
Part No.: 01029449
Air Gap

Battery Box
Part No.: 01029451
PARTS INCLUDED:
3/8" x 1/4" Tube Adapter

4

the kitchen faucet and allow all water to drain
from line.
SETTING CAPACITY AND TDS FUNCTION
NOTE: Set capacity and TDS function before starting installation.
NOTE: To access the dip switches for setting capacity and TDS function,
open the control box by removing the three screws in the rear cover.
Find the dip switches on the front of the circuit board.
SW2 and SW3 set the time and capacity for the lter reminder.
SW2: OFF = 500 gallons ON = 1000 gallons
SW3: OFF = 180 days ON = 365 days

The system will measure the dierence between the feed and product
water to determine if the RO is working.
SW1: OFF = Disabled ON = Enabled
SW6 is used for production testing and should be left in the o position.
INSTALLATION
NOTE: Refer to the manual provided with your filter/RO for installation
instructions specific to that system.
NOTE: Some installations may require adapters and ttings not included with
the product. Review the manual and your installation before beginning.
NOTE: Consult your local plumbing codes and install accordingly.
Disconnect the cold water line from the cold water

NOTE: 
is used, you may need to shorten the pipe using
a hacksaw or pipe cutter to accommodate the
control box.
SW6 SW3 SW2 SW1
ON

5
Connect the inlet on the RO/Filter system to the
port marked "RO/Filter >." Wet the end of the
plastic tubing with water and push it into the
quick connect tting adapter approximately 5/8˝
until it stops.
NOTE: This connection is plugged for remote


NOTE: This is the line that would normally come
from the supply tee or valve.
NOTE: Use the supplied adapter if your system
uses a 1/4" tube.
Connect the outlet on the RO/Filter system to the
port marked "RO/Filter <." Wet the end of the
plastic tubing with water and push it into the
quick connect tting adapter approximately 5/8"
until it stops.
NOTE: This is the line that would normally go to
your dedicated faucet.
NOTE: Connect the tank and/or post lter in
this line if required for your lter/RO system.

valve as shown. Tighten the lower end of cold water
line onto the top of the control box.
NOTE: The control box must be in a
vertical position.
NOTE: If space does not allow for mounting the
control box onto the valve, it can be alternatively
hung on a wall when using the holes on the back


6
AIR GAP
RO AIR GAP INSTALLATION
NOTE: These steps are only for RO installations using an air gap.
NOTE: If your ltration system is not an RO, skip to System Startup on Page 
NOTE: Install the drain connection to the drain plumbing according to the manual
provided with your RO system.
Connect the drain line coming from the RO
system to the small connection of the air
gap device.

top as possible and in a vertical orientation.
NOTE: Failure to mount the air gap device
vertically will cause it to leak water.
Connect the large tting of the air gap device to
the connection on the drain plumbing.





of the control box.
NOTE: The control box will beep and ash the
power light when powering up.
NOTE:

Conrm that the bypass valve is in the closed

Turn on the cold water supply and check for leaks.
If it leaks, refer to troubleshooting.
Use the provided screw to hang the battery box on
the side of the cabinet.
BYPASS

8

Turn on the faucet to full cold and push the button
to activate the system.
NOTE: The blue capacity lights should appear if
the button and control box are communicating.
NOTE: The button can be turned o with
a second push or by turning o the faucet.
NOTE: After startup, flush your system
according to manufacturer's specications.
It might take a few cycles for the button to
stay on while air is purged from the system.

remote button.

9

depending on lter capacity remaining,
6 lights = >80% and 1 light = <10%.
Culligan Logo: Flashes when treated water is not
available from the faucet. Stays solid while treated
water is being dispensed from the faucet.
Alert Indicator: Illuminates when the control box
batteries need replacing, lters need replacing, or
RO membrane needs replacing.
BUTTON DISPLAY GUIDE
CONTROL BOX OPERATION
RESET POWER
REPLACE BATTERIES
REPLACE FILTERS

Reset button for filter capacity.
Power: Flashes green at power up, lter capacity
reset, and while dispensing ltered water. Continues
to ash for 1 minute after the ow of ltered water
has stopped.
Replace Batteries: Flashes red when the batteries
for the control box need to be replaced. This indicator
automatically clears when new batteries are detected.
Replace Filters: Flashes red when the lters have
less than 10% of their life remaining due to ow or
time. This indicator is reset by pressing the reset
button for two seconds.

treated water has a TDS level greater than 25% of
the untreated water. This indicator will automatically
reset when low TDS water is detected.

10
TROUBLESHOOTING
LEAKS AT FILTER/RO INLET OR OUTLET CONNECTION:
 
and then conrm that the end of the tubing has a clean, square cut.

Low ow rates may not activate the control box electronics. Refer to your system manual to trouble
shoot a low ow condition.

Conrm that the bypass valve is in the down/closed position.

Some materials may block the wireless signal more than others. Try moving the button to an area on

FILTERED WATER FLOW WON'T TURN OFF: Low batteries for the control box can cause the system
to be stuck in the ltered position. The bypass valve can be used to allow unltered water ow to the
faucet while the issue is being corrected.


INTEGRITY