CyberData 011414 Manual

Quick Reference 931336A © 2017, CyberData Corporation, ALL RIGHTS RESERVED© 2017, CyberData Corporation, ALL RIGHTS RESERVED 931336A Quick Reference
Connecting the Keypad Intercom (Service Loop Routing)
Securing the Intercom
Contacting CyberData
is Not Provided
Network Cable
Creates Service Loop
the Custom Enclosure to
Faceplate &
PCB Assembly
Screw (6x)
Faceplate Mounting
Custom
Enclosure
Route Cable inside
Nut to Ground Lug
Inside the Custom Enclosure
is Not Provided
Ground Cable
Creates Service Loop
the Custom Enclosure to
Ground Lug
Faceplate &
PCB Assembly
Screw (6x)
Faceplate Mounting
Custom
Enclosure
Route Cable inside
Ground Cable Installation Network Cable Installation
Torx Key
Torx Screws Faceplate &
PCB Assembly
Custom
Enclosure
GENERAL ALERT
Caution
Equipment Hazard: Do not use an electric
or power screwdriver to fasten the face plate
and PCB assembly to the gang box. To prevent
over-torque damage to the gasket, do not apply
more than 10 inch-pounds force. Over-torquing
will cause the gasket to tear, risk moisture intrusion,
and effectively void the manufacturer's warranty.
Note: To mount the intercom, use methods
compliant with local electrical codes.
Note: More installation and mounting
information is illustrated in the Operations Guide.
Network cable
and ground wire
(Not Provided)
Custom Enclosure
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
Typical System Installation
Getting Started
• Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011414/
• Create a plan for the locations of your Keypad Intercoms.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Keypad Intercom Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
a. Default if there is not a DHCP server present.
Video Outdoor Intercoms with Keypad
*More installation and mounting
information is available in the
Operations Guide.
802.3af Compliant Ethernet Switch
IP Phone IP PBX Server
Accessories
Spacer for Half-inch Set Screw Connector
531085B Hole Plug Assembly
Accessory Kit Security Torx MS
Accessory Kit
Carriage Bolt Bolts
Carriage Bolt Nuts
Carriage Bolt Washers
Mounting Component Security Torx Key
(1) Intercom Assembly
Installation Quick Reference
SIP-enabled h.264 Video Outdoor Intercom with Keypad
011414
The IP Endpoint Company

© 2017, CyberData Corporation, ALL RIGHTS RESERVED 931336A Quick Reference Quick Reference 931336A © 2017, CyberData Corporation, ALL RIGHTS RESERVED
Terminal Block Connections
RTFM Button
Call Button
7.480 [190.00]
Dimensions are in Inches [Millimeter]
5.118 [130.00]
5.198 [132.03]
2.386 [60.59]
Camera
Keypad
Features Dimensions (Front and Side View)
Wire(s) in
Tin Wire to 0.25 inch [6mm]
Terminal block can accept up to 16 AWG wire.
Tool required for terminal block screw:
Size #00 Phillip Drive Screwdriver
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
34
RTFM Button (SW1)
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a five
second window.
Note The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
Dimensions (Rear View and Mounting Holes)
Conduit Mounting Restrictions (Rear Entry)
ø0.280 [ø7.11]
3.740 [95.00]
1.690 [42.93]
0.869 [22.07]
3.380 [85.85]
1.690
(3 Places)
[42.93]
ø0.854 [ø21.69]
Dimensions are in Inches [Millimeter]
1/2" Conduit
(Not Provided)
Here Connector
1/2" Conduit
(Not Provided)
Cable
Network
Spacer
Add
(Not Provided)
Cable
Network
(Not Provided)
1/2" Conduit
1/2" Conduit
Spacer Connector
(Not Provided)
(Not Provided)
Here
Add
With Shroud Without Shroud