CyberData 10630 User manual

PoweredUSB 6-Port 2.0 Hub 
Operations Guide
Part #010630
Document Part #931035A
CyberData Corporation
3 Justin Court
Monterey, CA 93940
[phone]
The IP Endpoint Company

CyberData Corporation 931035A Operations Guide
VoIP Outdoor Intercom Operations Guide 931035A
Part # 010630
COPYRIGHT NOTICE:
© 2015, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The fastest way to get technical support for your Point of Sale product is
to submit a Technical Support form at the following website:
http://www.cyberdata.net/support/contactsupportretail.html

Phone: [phone], Ext. 333
Email: [email protected]
Fax: [phone]
Company and product information is at www.cyberdata.net.
The IP Endpoint Company

Operations Guide 931035A CyberData Corporation
Revision Information
Revision 931035A was released on January 15, 2015, and has the following changes:
• Updates Figure 1-1, "External Components Identification"
• Updates Figure 1-6, "JP2 Connector with jumper OFF"
• Updates Figure 1-7, "JP2 Connector with jumper ON"
• Updates Section 1.3, "Features"
• Updates Section 1.9, "JP2 Jumper Control Settings"
• Updates Section 1.7.1.1, "Standard USB Lower A supply:"
• Updates Section 1.7.1.2, "PoweredUSB Upper A supply:"

CyberData Corporation 931035A Operations Guide
Pictorial Alert Icons
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the hazard.
Ground
This pictoral alert indicates the Earth grounding connection point.
GENERAL ALERT

CyberData Corporation 931035A Operations Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
GENERAL ALERT
GENERAL ALERT

i
Operations Guide 931035A CyberData Corporation
Contents
Chapter 1 Product Overview 1
1.1 Product Description ..................................................................................................................1
1.2 Compatibility .............................................................................................................................1
1.3 Features ...................................................................................................................................1
1.4 Product Components (included items) .....................................................................................1
1.5 External ....................................................................................................................................2
1.6 Installation ................................................................................................................................3
1.6.1 Mounting ........................................................................................................................3
1.6.2 Connections ...................................................................................................................3
1.6.3 USB PoweredUSB Connections .....................................................................................4
1.6.4 Connector Keying ...........................................................................................................5
1.6.5 Pin Out ...........................................................................................................................6
1.6.6 PoweredUSB Cable Sources .........................................................................................6
1.7 Operation ..................................................................................................................................7
1.7.1 Current Maximums: ........................................................................................................7
1.8 PC Stand-by / Wake Peripheral Control ...................................................................................7
1.9 JP2 Jumper Control Settings ....................................................................................................8
1.9.1 Jumper OFF (Green mode) ............................................................................................8
1.9.2 Jumper ON .....................................................................................................................9
1.10 Regulatory ............................................................................................................................10
1.10.1 License note: ..............................................................................................................10
1.10.2 Documentation Note: .................................................................................................10
1.10.3 Contact Information: ...................................................................................................10
1.10.4 Safety .........................................................................................................................11
1.10.5 EMC ...........................................................................................................................11

1
Operations Guide 931035A CyberData Corporation
1 Product Overview
1.1 Product Description
The CyberData PoweredUSB 6-Port 2.0 Hub provides a simple and affordable way to add up to six
PoweredUSB ports to your PC that are controlled by the PC’s Stand-by/Wake commands. With this
USB add-on, it is easy to connect devices that need more than the standard USB interface supplied
500mA of +5 volts.
1.2 Compatibility
• IBM PC Windows XP and higher operating system compatible
• Apple Computer Compatible
• The USB 2.0 Standard is fully supported.
• The HUB controller on this product is USB 2.0 compliant for a “powered hub”.
1.3 Features
• 6 PoweredUSB ports
• One +24 volt at 2.5A
• Five +12 volt at 2.5A each
• Short circuit and over-current protected
• No external power supply required
• Plug-N-Play installation
• Peripheral power controlled by PC Stand-by/Wake commands
• LED indicators to show port enumeration status
• Two year warranty
1.4 Product Components (included items)
• CyberData PoweredUSB Hub (1)
• Rubber Feet (4)
• Instruction / Operations Manual (this document) (1)
• Host USB cable strain relief clamp (1)

Product Overview
External
Operations Guide 931035A CyberData Corporation
2
1.5 External
Figure 1-1. External Components Identification
Note The AC Power Cable is only supplied to US customers. User should use ONLY a suitable
Power Supply cord that conforms to IEC 60320/C13.
AC power 
cable IN
Fan Host cable clamp
mounting hole
Port 1
+5V
Upper
Port 2
+5V
Upper
Port 3
+12V
Upper
Port 4
+12V
Upper
Port 5
+12V
Upper
Port 6
+24V
Upper
On/Off
power switch
USB series
“B” host PC
connector
Active LED indicates 
Hub enumeration under 
OS control
LED Function
PoweredUSB Ports:
• A single LED provides the port status indication of
each port.
• The Hub tests three parameters:
• PoweredUSB Voltage. This is the higher current
voltage used to provide power to the peripheral
• USB Port Enumeration. This confirms that the Host
and the peripheral device are communicating
• USB Error condition. USB 2.0 provides a single
when there is an abnormal USB condition
• The LED has three display states:
• Green = PoweredUSB voltage is good, USB port
is enumerated, No USB error condition.
• Amber = Any one of the three tested parameters
are incorrect.
• Off = Power is off for the entire hub or major Hub
fault.
Host Port Active LED
• The host port has an associated green LED that
illuminates when the connection to the upstream host
is enumerated.

Product Overview
Installation
Operations Guide 931035A CyberData Corporation
3
1.6 Installation
1.6.1 Mounting
The unit may be mounted in any orientation except that the Powered USB connectors should not be
facing upward to prevent conductive materials from entering the connectors. Mounting feet are
included for setting on a flat
surface . The only restriction is that the fan and intake vents are not
blocked or have the air flow restricted.
Note In order to maintain safe operation of the unit and to reduce the risk of equipment damage,
this unit should not be mounted with any openings facing upward. This unit is intended to be
operated in a dry location.
1.6.2 Connections
1.6.2.1 AC
The AC connection is a standard IEC 60320 type C13. This cable is supplied for North American
operations ONLY. If used outside of North America user should use ONLY a suitable Power Supply
cord that conforms to IEC 60320/C13
Input Requirements:
Voltage: 100 - 240 VAC
Frequency: 60 / 50 Hz
Input Current: 4.0A (RMS) at 115VAC or 2.0A (RMS) at 230VAC
1.6.2.2 Host Connector
The Host connector is a standard high-speed USB “A” to “B” type cable and can be procured from a
variety of sources.
Max length of 5 meters (16.4 feet) with good quality cable

Product Overview
Installation
Operations Guide 931035A CyberData Corporation
4
Figure 1-2. Connections
1.6.3 USB PoweredUSB Connections
The PoweredUSB connections are a standard “A” type connector with 4 extra pins designed to
supply higher voltages. The “A” connector side of this product can be used, by itself, without the
locking PoweredUSB connector being used.

Product Overview
Installation
Operations Guide 931035A CyberData Corporation
5
Figure 1-3. USB PoweredUSB Connections
1.6.4 Connector Keying
The PoweredUSB connectors are keyed in such a way as to only allow the correct voltage cables to
be installed.
Figure 1-4. Connector Keying Picture with Color Coding
12 Volt Keyed
Ports 1 - 5
Te a l R e d
24 Volt Keyed
Port 6

Product Overview
Installation
Operations Guide 931035A CyberData Corporation
6
Figure 1-5. USB PoweredUSB Socket Connector Pin Assignments
1.6.5 Pin Out
1.6.6 PoweredUSB Cable Sources
Custom and standard cable assemblies may be ordered from CyberData or they may be procured
from other sources.
For more information about the cables and connectors of PoweredUSB use the following link:
www.poweredusb.org
Table 1-1. Pin Out
Pin Signal Description
1 Vbus USB standard “A”
2 D- USB standard “A”
3 D+ USB standard “A”
4 Ground USB standard “A”
5 Ground USB PoweredUSB
6 Vplus USB PoweredUSB
7 Vplus USB PoweredUSB
8 Ground USB PoweredUSB
Shell Shield

Product Overview
Operation
Operations Guide 931035A CyberData Corporation
7
1.7 Operation
The device is a standard USB Hub compliant to the USB 2.0 specification, with the addition of the
PoweredUSB ports. When connected to a Host, it enumerated as a "Generic USB Hub".
1.7.1 Current Maximums:
1.7.1.1 Standard USB Lower A supply:
Each lower portion of the A Ports provides +5V @ 500mA. If more than 500mA is drawn from any
port, that port goes into USB Over-current, the +5 volts is turned off, and the fault condition is
reported to the host according to USB 2.0 Specifications.
1.7.1.2 PoweredUSB Upper A supply:
+12V Ports (5) 
+24V Port (1)
The +12V ports are protected by a PTC that allows 2.5A continuous current. This PTC will go into
protection if a sustained overload is applied.
The +24V Port is also protected by a PTC that allows 2.5A continuous current. This PTC will go into
protection if a sustained overload is applied (For example, with a 3 amp load, the PTC will shut off
port power after approximately 30 seconds).
FOR ALL PORTS:
Specific short protection is provided for the Standard USB connector and the PoweredUSB
connector.
Standard lower USB A portion of the connector
This portion of the connector will not support more that 500mA and the power will be shut down
immediately if any load is greater than 500mA.
PoweredUSB portion of the USB connector
This portion of the connector is a little more flexible and will allow for temporary overloads in
accordance with PoweredUSB specification 0.8g. But, in all cases, the connector is protected
against short circuits. Should any PoweredUSB port be shorted, the HUB will shut down
completely until the short is removed. Depending on the duration of the short, the power supply
may need to be turned off using the power switch on the side of the hub, for at least 30 seconds
before it can be turned on again.
1.8 PC Stand-by / Wake Peripheral Control
Under Windows operating systems, USB devices can be placed into low power Stand-by mode . The
PoweredUSB Hub expands on this feature and allows the operating system to control power to the
retail peripherals attached via the hub. A two-pin jumper (JP2) located next to the power connector
on the Printed Circuit Board controls this green feature.
Please read the JP2 Jumper Control settings
section below for details on controlling the standby
feature.

Product Overview
JP2 Jumper Control Settings
Operations Guide 931035A CyberData Corporation
8
1.9 JP2 Jumper Control Settings
Jumper JP2 controls the PC Stand-by/Wake Peripheral Control feature. Please refer to the Check-
Off list shipped with your Hub for the factory set status of this jumper. If you need to change
the jumper setting please contact CyberData for a addendum instruction on Hub case assembly/
disassembly.
1.9.1 Jumper OFF (Green mode)
When the jumper on JP2 is removed or the jumper is placed on a single pin (see Figure 1-6), the
Hub will be in the “Green” mode whereby the Hub will shutdown all peripherals and the power supply
fan whenever the Host PC is placed in Stand-by or is shut down. The Hub will exhibit the following
characteristics when in this mode:
1. Plug in power cord and turn on Hub power switch – Power supply fan does not come on, no
power to peripherals, no Active LED light, USB port LEDs light amber.
2. Plug in Host USB “B” connector from operational Host PC—Active LED lights once Hub
enumerates under OS control, fully compliant USB peripherals enumerate under OS control,
+12V and +24V power is turned on once peripherals enumerate correctly, and enumerated port
status LEDs change to green (un-enumerated port LEDs stay amber).
3. Shutting down or placing Host PC in Standby (or unplugging Host USB “B” connector)—Active
LED light extinguishes and USB port LEDs light amber, +12V and +24V power to peripherals
and power supply fan turn off, peripherals and Hub lose enumeration on PC.
Figure 1-6. JP2 Connector with jumper OFF
Power connectorJP2
JP2 Pin-1 and Pin-2
normally not jumpered

Product Overview
JP2 Jumper Control Settings
Operations Guide 931035A CyberData Corporation
9
1.9.2 Jumper ON
When the jumper is placed on both pins of JP2 the “Green” mode is disabled ( see Figure 1-7) . The
Hub will exhibit the following characteristics when in this mode:
1. Plug in power cord and turn on Hub power switch – Power supply fan will come on, power is
supplied to peripherals, no Active LED light, and USB port LED lights amber.
2. Plug in Host USB “B” Connector from operating PC – Active LED lights once Hub enumerates
under OS control. Peripherals enumerate under OS control
and enumerated USB port status
LEDs light
green .
3. Shutting down or placing Host PC in Standby (or unplugging Host USB “B” connector)—Active
LED light extinguishes and USB port LEDs light amber, +12V and +24V power to peripherals
and power supply fan stay on, peripherals and Hub lose enumeration on PC.
Figure 1-7. JP2 Connector with jumper ON
Power connectorJP2
JP2 Pin-1 and Pin-2
normally not jumpered

Product Overview
Regulatory
Operations Guide 931035A CyberData Corporation
10
1.10 Regulatory
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense. See Appendix A for
specifics.
Safety Compliance: See Appendix A
1.10.1 License note:
"The PoweredUSB controller board contains certain technology covered by a patent held by IBM
Corporation. Cyberdata has obtained a license from IBM that permits Cyberdata, among other
things, to make and to sell or lease products that incorporate this technology. The license also
permits these products to be resold or released by any entity after they have been initially sold by
Cyberdata."
1.10.2 Documentation Note:
The documents, labels, and markings supplied are intended for English speaking countries and
users.
1.10.3 Contact Information:
CyberData Corporation
3 Justin Court
Monterey, CA 93940
USA
Phone: [phone]
Fax: [phone]

Product Overview
Regulatory
Operations Guide 931035A CyberData Corporation
11
1.10.4 Safety
Safety Standard(s):
• UL62368-1 2nd Edition
1.10.5 EMC
US/CAN Complies with:
• Title 47 of the CFR, Part 15, Subpart B, Section 15.107(b)
• Title 47 of the CFR, Part 15, Subpart B, Section 15.109 (b)
• ICES-003