CyberData 11006 User manual

4-Port PoweredUSB 2.0 Hub
Operations Guide
with External Power Supply
Part #011006
CyberData Corporation
2555 Garden Road
Monterey, CA 93940
[phone]
930232A

CyberData Corporation 930232A Operations Guide
4-Port PoweredUSB 2.0 Hub Operations Guide 930232A
Part # 011006
COPYRIGHT NOTICE:
© 2007, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part
of this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or
such products, software, firmware, and/or hardware. CyberData Corporation reserves the right to
make changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by
third parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Phone: [phone]
Technical Support Ext. 333
[email protected]
Fax: [phone]
Company and product information at www.cyberdata.net

Operations Guide 930232A CyberData Corporation
iii
Chapter 1 Product Overview 1
Chapter 2 Installing and Using the 4-Port PoweredUSB Hub 3
2.1 Product Components List .....................................................................................................................3
2.2 Product Compatibility ...........................................................................................................................4
2.3 Installation ...............................................................................................................................................5
2.4 Connections ............................................................................................................................................5
2.4.1 Power Supply ..............................................................................................................................5
2.4.2 Host Connector ............................................................................................................................6
2.4.3 PoweredUSB Connections .........................................................................................................6
2.4.4 Connector Color Keys ................................................................................................................7
2.4.5 Peripherals Connections to the SiP VoIP and PoE Speaker ..................................................7
2.4.6 Peripheral Cable Connection Options .....................................................................................9
2.5 Operation ...............................................................................................................................................10
2.6 Port Electrical Specifications ..............................................................................................................12
Appendix A Regulatory and Safety Information 13
Appendix B Setting up the Hub on Windows XP 15
Appendix C Troubleshooting/Technical Support 17
C.1 Frequently Asked Questions (FAQ) .................................................................................................17
C.2 Documentation ....................................................................................................................................17
C.3 Contact Information ............................................................................................................................17
C.4 Warranty ...............................................................................................................................................18
Index 19
Contents

CyberData Corporation 930232A Operations Guide
iv

1
Operations Guide 930232A CyberData Corporation
1 Product Overview
The SiP VoIP and PoE Speaker provides a simple, affordable way to add up to four PoweredUSB
ports to your PC. These additional ports are controlled by the PC’s Standby and Wake commands.
This add-on Hub makes it easy to connect the PC to devices that require more than the 500mA of +5
volts supplied with the standard USB interface.
Figure 1-1. CyberData 4-Port PoweredUSB 2.0 Hub
Product features ●4 PoweredUSB ports
●Four +12 volt up to 1.5A each
●Short circuit and over current protected
●Multiple power supply options
●Plug-n-Play installation
●Peripheral power controlled by PC stand-by and wake commands
●LED indicators for port power output and USB 2.0 status
●Two-year warranty
License note The PoweredUSB controller board contains certain technology that is covered by an IBM®patent.
CyberData Corporation is licensed with IBM to manufacture, and to sell or lease products that
incorporate this technology. This license also permits other entities to resell or release these
Cyberdata products after they have been purchased from CyberData.
Documentation
note
The documentation for this product is released in an English language version only.

CyberData Corporation 930232A Operations Guide
Product Overview
2

3
Operations Guide 930232A CyberData Corporation
2 Installing and Using the 4-Port
PoweredUSB Hub
This chapter provides the instructions, illustrations, and background information you need to
install, and begin working with the SiP VoIP and PoE Speaker.
Figure 2-2. CyberData 4-Port PoweredUSB 2.0 Hub
2.1 Product Components List
The 4-Port PoweredUSB 2.0 Hub package includes these parts:
●(1) SiP VoIP and PoE Speaker
●Power Supply, 24VDC, Desk-top, 4-Pin Hosiden style plug
●(1) Accessory Kit
• (1) Short USB 2.0 Hi-Speed host cable
• (1) Host USB cable strain relief clamp
•(1)4-Port PoweredUSB 2.0 Hub Operations Guide

CyberData Corporation 930232A Operations Guide
Installing and Using the 4-Port PoweredUSB Hub
Product Compatibility
4
Figure 2-3. CyberData 4-Port PoweredUSB 2.0 Hub—Front View
Figure 2-4. CyberData 4-Port PoweredUSB 2.0 Hub—Back View
2.2 Product Compatibility
The SiP VoIP and PoE Speaker is compatible with the following operating systems and USB
standards.
Port Power LED +12V PoweredUSB Ports
Hub Power LED
Link LED
Port 1 Status LED
Lower portion of PoweredUSB Port connectors are
Standard USB 2.0 Hi-Speed “A” ports
+24V for
up to 2.5
Amp load
+24V for
up to 6.5
Amp load
USB Host
Connector
(Type B)
Strain
Relief
Operating systems USB
Windows 2000 and XP 2.0 Standard
LINUX PoweredUSB 0.8g
Mac OS-X

Installing and Using the 4-Port PoweredUSB Hub
Installation
Operations Guide 930232A CyberData Corporation
5
2.3 Installation
The SiP VoIP and PoE Speaker is a tabletop unit with mounting feet that sit on a flat surface.
2.4 Connections
This following topics provide illustrations and information on connecting the SiP VoIP and PoE
Speaker to power supplies, the host, and peripheral devices.
2.4.1 Power Supply
The PoweredUSB specification requires supplying +12V at 1.5A to each voltage designated port.
These requirements are met only if the power supply has sufficient wattage for this amount of
power.
The Epson PS180 brick and Dell printer power supply are examples of lower-cost alternate power
supplies that can be used with this Hub and peripherals requiring less power. Two power plug
receptacles are provided on the back of the SiP VoIP and PoE Speaker to facilitate the use of alternate
power supplies.
The three-pin connector is normally used for the Dell and Epson Bricks. The four-pin connector is
used for a high-current power supply. See Figure 2-9 for an illustration of cable routing from the SiP
VoIP and PoE Speaker.
CAUTION The P1 and P2 DC input jacks on the back of this Hub are for input only. Do not plug
power supplies into both input jacks simultaneously as equipment damage that might void the
product warranty could occur.
Figure 2-5. Power Connectors—Back View
+24V for
up to 2.5
Amp load
+24V for
up to 6.5
Amp load
USB Host
Connector
(Type B)
Strain
Relief

CyberData Corporation 930232A Operations Guide
Installing and Using the 4-Port PoweredUSB Hub
Connections
6
2.4.2 Host Connector
The connection to the host computer is achieved via a standard USB 2.0 certified Hi-Speed “A” to
“B” cable that is included in the Accessory Kit, or with any equivalent USB 2.0 certified Hi-Speed
cable. Refer to the Section 2.1, "Product Components List" for information about the Accessory Kit.
Figure 2-6. Host connector with strain relief
2.4.3 PoweredUSB Connections
The PoweredUSB connections are standard USB “A” connectors with four extra pins to supply
higher voltages. See Figure 2-8 for an illustration. The lower portion of the “A” connector side on
this product can be used alone, without the locking PoweredUSB connector.

Installing and Using the 4-Port PoweredUSB Hub
Connections
Operations Guide 930232A CyberData Corporation
7
2.4.4 Connector Color Keys
The PoweredUSB connectors are color keyed so that only the correct voltage cables can be installed.
Figure 2-7. Color-Coding for Connectors
Figure 2-8. USB PoweredUSB Socket Connector Pin Assignments
2.4.5 Peripherals Connections to the SiP VoIP and PoE Speaker
This figure illustrates the cable routing from the SiP VoIP and PoE Speaker to the Dell Retail
Integrator.
Teal Red
12 Volt Keyed
1.5A each
Ports 1,2, and 3
12 Volt Keyed
1.5A each
Ports 1,2, and 3
PIN OUT
Pin Signal Description
1Vbus USB standard “A”
2D- USB standard “A”
3D+ USB standard “A”
4Ground USB standard “A”
5Ground USB PlusPower
6Vplus USB PlusPower
7Vplus USB PlusPower
8Ground USB PlusPower
Shell Shield

CyberData Corporation 930232A Operations Guide
Installing and Using the 4-Port PoweredUSB Hub
Connections
8
Figure 2-9. Top view of Hub PoweredUSB cable routing
+12V PoweredUSB Connectors
CyberData 4-Port PoweredUSB Hub

Installing and Using the 4-Port PoweredUSB Hub
Connections
Operations Guide 930232A CyberData Corporation
9
2.4.6 Peripheral Cable Connection Options
Figures 10 through 16 provide examples of peripheral cable combinations and connection options
for the SiP VoIP and PoE Speaker. The following table provides details about the CyberData
PoweredUSB Cables displayed in these figures.
PoweredUSB
cable sources
Custom cables of different lengths and colors can be purchased from CyberData as follows:
●Via email: [e-mail]
●Via phone: Sales [phone] Extension 334
Figure 2-10. Cable, +12V PoweredUSB to 2x4 PoweredUSB
Table 2-1. CyberData PoweredUSB Cables
Figure PoweredUSB Cable Description CyberData Part Number
Figure 2-10 12V to 2x4 010693C
Figure 2-11 12V to 12V Power Jack Contact CyberData
Figure 2-12 12V to “Y” Cable, RS232 and Power Jack 010763

CyberData Corporation 930232A Operations Guide
Installing and Using the 4-Port PoweredUSB Hub
Operation
10
Figure 2-11. Cables; +12V PoweredUSB to +12V Power Jack and RS-232 to RS-232
Figure 2-12. RS232 to USB Converter “Y” Cable +12V (PC Enumerates this device as an RS-232 COM port)
2.5 Operation
The SiP VoIP and PoE Speaker is a standard USB Hub that complies with the USB 2.0 specification,
and adds PoweredUSB ports. When connected to a Host, it is enumerated as a Generic USB Hub. This
Hub also meets the PoweredUSB .08g specification. For more information about this specification,
go to www.poweredusb.org.
POS peripheral
caveat
According to the USB 2.0 specification, devices attached to a USB interface should enumerate from
the Hub’s USB Vbus, regardless of the PoweredUSB powered ports. Some POS devices do not
comply with this specification, and will not enumerate unless the upper sections of the PoweredUSB
ports are active.

Installing and Using the 4-Port PoweredUSB Hub
Operation
Operations Guide 930232A CyberData Corporation
11
When running on operating systems such as Windows XP with no devices attached (an empty Hub),
the operating system turns the Hub off. The operating system does not detect non-compliant
peripherals when they are hot-plugged into an empty Hub. Consequently PoweredUSB power is
not supplied to the peripheral. In this case, you can restore correct operation as follows.
1. Unplug the Host side connection for five seconds, and then plug it in again.
2. Be sure that at least one USB device is plugged in when the computer is booted, or leaves
standby mode.
3. Plug in a standard USB compliant device, such as a mouse or keyboard.
4. Disable the low-power, standby operation. With this configuration, power is always supplied to
the PoweredUSB ports regardless of the PC’s operational state. For more information, contact
CyberData as instructed in Appendix C, "Troubleshooting/Technical Support".

CyberData Corporation 930232A Operations Guide
Installing and Using the 4-Port PoweredUSB Hub
Port Electrical Specifications
12
2.6 Port Electrical Specifications
The SiP VoIP and PoE Speaker adheres to the USB 2.0 electrical specifications as follows:
Standard USB
lower A supply
Each lower portion of the PoweredUSB port provides +5V @ 500mA. If more than 500mA are drawn
from a port, that port goes into USB over current, the +5 volts is turned off, and the condition is
reported to the host according to USB 2.0 specifications.
PoweredUSB
supply
The listed maximum currents depend on the selected power supply. The +12V PoweredUSB ports
are protected with active over current circuits. If an over current condition occurs, unplug the DC
connection, remove the overcurrent condition, and re-cycle the DC connection to the Hub by
unplugging it, and then plugging it in again.
●+12V Ports (3) – 1.5A each

13
Operations Guide 930232A CyberData Corporation
Appendix A: Regulatory and Safety
Information
Regulatory
standards
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Safety standards ●UL60950-1; Information Technology Equipment
●CSA C22.2 No. 60950-01, Information Technology Equipment
●EN60950-1, Information Technology Equipment
●IEC60950-1, Information Technology Equipment
EMC For the USA and Canada, this device complies with:
●Title 47 of the CFR, Part 15, Subpart B, Section 15.107(b)
●Title 47 of the CFR, Part 15, Subpart B, Section 15.109 (b)
●ICES-003
CE Declaration of
Conformity
This device complies with:
●Directive 89/336/EEC
●EN55022 Class A 1998
• EN61000-3-2: 2000
• EN61000-3-3: 1995
●EN55024: 1998
• EN61000-4-2: 1995
• EN 61000-4-3:1996
• EN 61000-4-4: 1995
• EN 61000-4-5: 1995
• EN 61000-4-6: 1996
• EN 61000-4-8: 1993
• EN 61000-4-11: 1995

CyberData Corporation 930232A Operations Guide
14

15
Operations Guide 930232A CyberData Corporation
Appendix B: Setting up the Hub on
Windows XP
For connecting the SiP VoIP and PoE Speaker to a PC running the Windows XP operating system,
keep in mind:
1. Microsoft XP Service Pack 1 or higher must be installed.
2. When connecting the Hub for the first time, it is important to perform the enumeration
correctly. A Microsoft XP Service Pack issue does not enumerate and recognize a Hub when no
devices are attached to it. To correctly enumerate the SiP VoIP and PoE Speaker, attach a
peripheral whose drivers are included in Windows XP, such as a USB mouse, prior to
enumerating the Hub. To accomplish this:
a. Connect a USB mouse to one of the lower,standard USB, Hub ports.
b. Connect the power cord to the Hub.
c. With the PC powered up, connect the host control cable from the Hub to a USB port on the
PC. Doing so displays the Found new hardware dialog, indicating that the PC is searching for
drivers for the Hub.
d. When the PC completes the driver search, it displays the Found new hardwaredialog, in
search of a driver for the mouse. If required, click Next in all screens of the wizard to
complete the driver selection for the mouse.
At this point, you should be able to plug in and install a USB device provided you have also
installed its drivers, or have them available for installation.

CyberData Corporation 930232A Operations Guide
16