CYP MA-421 User manual

MA-421
4x2+1 HDMI Input & HDBaseT/HDMI Output Matrix and
Amplifier with AVLC, 4KHDR
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 08/02/2019 First release
v1.01 12/02/2019 Added Sections 6.3, 6.4, 6.7, 6.8, 8.2;
updated Sections 6.6, 8.2

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................7
3. Package Contents ..................................7
4. System Requirements ...........................7
5. Features..................................................8
6. Operation Controls and Functions.......9
6.1 Matrix Front Panel ..................................... 9
6.2 Matrix Rear Panel.....................................10
6.3 Receiver Front Panel...............................11
6.4 Receiver Rear Panel.................................12
6.5 Remote Control........................................13
6.6 IR Cable Pinouts .......................................17
6.7 RS-232 Bypass Pinout.............................17
6.8 Serial Control.............................................17
6.9 WebGUI Control .......................................18
6.10 Mobile Device App...............................37
6.11 Telnet Control .........................................43
6.12 RS-232 and Telnet Commands .........44
7. Connection Diagram .......................... 70
8. Specifications...................................... 71
8.1 Technical Specifications -Matrix.........71
8.2 Technical Specifications - Receiver....72
8.2 Video Specifications................................73
8.3 Audio Specifications...............................75
8.5 HDBaseT Features....................................76
9. Acronyms............................................. 77

6
1. INTRODUCTION
This 4×2 HDMI to HDBaseT/HDMI Matrix with Stereo Amplier provides
high performance audio and video support, including HDR and
ARC, making it ideally suited for multi-zone residential or corporate
installations. Any of four high-bandwidth (18Gbps) HDMI sources may be
routed to either of the two HDBaseT Zone outputs via a single Cat.5e/6/7
cable (up to 70m at 1080p or up to 35m at 4K) with Zone A’s output also
being mirrored to a local HDMI output. Despite HDBaseT’s 10.2Gbps
bandwidth limitation, 4K UHD HDMI video sources, up to and including
4K@60Hz (4:4:4, 8-bit) as well as 10/12-bit sources with HDR, are able to
be processed and extended by the use of AVLC (Adaptive Visually Lossless
Compression) when connected to compatible AVLC Receivers providing
gorgeous video quality.
Pass-through of multiple digital audio formats such as LPCM 7.1,
Bitstream and advanced HD Bitstream with audio sampling rates up to
192kHz are supported via the HDBaseT and HDMI outputs. Additionally,
the integrated stereo amplier provides up to 40 watts of power (20W per
channel) for local speakers to output the audio from the sources routed
to either of the HDBaseT outputs, or from the ARC audio coming back
from the display connected to the HDMI output, oering a exible sound
experience (LPCM 2.0 sources only).
This unit also contains a specialised IR learning and smart-routing
functionality. IR codes from each connected source’s remote can be
learned and then recalled using this unit’s dedicated remote control,
or the mobile device app. Intelligent IR routing ensures that only the
IR signals appropriate to the source being viewed in the current zone
are used by the dedicated remote control while the mobile device app
provides the ability to send IR commands to control any connected
source. IR command sets may also be uploaded or downloaded
to/from the unit via XML les.
The 48V PoH (Power over HDBaseT) function can provide power to
compatible Receivers, providing greater exibility in installations. This unit
can be controlled in a wide variety of dierent ways including front panel
buttons, RS-232, IR remote, Telnet, WebGUI and a mobile device app.

7
2. APPLICATIONS
Conference room installation
Multi-zone home theatre
Meeting room connection
Classroom display
3. PACKAGE CONTENTS
1×HDMI to HDBaseT/HDMI Matrix with Stereo Amplifier
1×HDMI over HDBaseT Receiver
1×24V/2.7A DC Power Adapter
2×Power Cord
2×2-pin Terminal Block
5×3.5mm to IR Blaster Cable
1×Remote Control (CR-186)
1×Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as media players, video game consoles
or set-top boxes.
HDMI receiving equipment such as HDTVs, monitors or audio
amplifiers.
The use of compatible HDBaseT receivers with 48V PoH and AVLC
support is recommended.
An active network connection from a switch or router is required for
control of the unit via the mobile device app.
The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly
recommended.
HDMI cable distance can be impacted by the materials and design
of the cable used. The use of“Premium High Speed HDMI” cables is
highly recommended.

8
5. FEATURES
HDMI with HDR, 3D & 4K@60Hz support, DVI 1.0 compatible
HDCP 2.2 and HDCP 1.x compliant
Routes four HDMI sources to two HDBaseT outputs with a mirrored
HDMI output with support for automatic input switching
Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-bit) video input
and output
Note: Support of resolutions with bandwidth above 10.2Gbps via HDBaseT
requires a compatible AVLC Receiver.
Supports 'Deep Colour' input and output up to 12-bit
Supports 10-bit and 12-bit HDR (High Dynamic Range) input/output
HDBaseT feature support: HD Video and Audio, 48V PoH and Control
(bi-directional IR pass-through)
Supports standard 48V PoH from the unit to connected HDBaseT
Receivers (compatible Receivers only)
HDBaseT outputs provide simultaneous transmission of uncompressed
video, audio and data over a single Cat.5e/6/7 cable up to 70m/230ft
at 1080p and 35m/115ft at 4K
Integrated AVLC (Adaptive Visually Lossless Compression) activates
when the bandwidth requirements of the source are beyond 10.2Gbps
(340MHz) allowing for support of sources up to 18Gbps (600MHz)
with no loss of visual quality
Per-output, selectable, 4K to 1080p down-scaling/colour space
conversion (4:4:4 to 4:2:0)
Supports pass-through of LPCM 7.1, Bitstream and advanced HD
Bitstream audio formats
Supports the Audio Return Channel (ARC) function to transmit digital
audio from an ARC-enabled TV connected to the HDMI output (LPCM
2.0 only)
Selectable stereo analogue audio breakout mirrored to both amplified
(20W per channel) and un-amplified (3.5mm headphone) connections.
(LPCM 2.0 only)
Support for learning IR remote codes for on-demand retransmission
Advanced EDID management with 8 Internal, 3 external EDIDs copied
from connected devices, and 4 custom user provided EDIDs
Controllable via front panel buttons, RS-232, IR remote, Telnet, WebGUI
and a mobile device app

9
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Matrix Front Panel
1234 1234
ZONE
BAARC
IR SERVICEZONE AZONE BAUDIO SELECT MUTE Vol –Vol +POWER
MA-421
1 2 3 4 5 67 8
1POWER Button and LED: Press this button to power the unit on (green
LED) or place it into standby mode (red LED).
Note: If the IR Auto Power Control function is turned on for any inputs/
outputs, this button will also turn on/off those devices that have IR
commands stored.
2ZONE A Button and LEDs: Press this button to sequentially switch
through the available inputs for Zone A. The LED will illuminate to
indicate which source is currently selected.
Note: The selected input will also be displayed on the mirrored HDMI
output.
3ZONE B Button and LEDs: Press this button to sequentially switch
through the available inputs for Zone B. The LED will illuminate to
indicate which source is currently selected.
4AUDIO SELECT Button and LEDs: Press this button to sequentially
switch through the available audio sources for both analogue outputs.
The LED will illuminate to indicate which source is currently selected.
The available sources are: Zone A’s current input, Zone B’s current
input, ARC audio from the HDMI output.
Note: If the display connected to the HDMI output does not support ARC,
no audio will be heard when the ARC source is selected.
5MUTE Button and LED: Press to toggle between muting and
unmuting the analogue audio output. The LED will illuminate when
mute is active.
Note: By default, the mute button only controls the amplified output. This
behavior can be adjusted via RS-232.

10
6VOL−/VOL+ Buttons and LEDs: Press or hold the +/− (plus/minus)
buttons to increase or decrease the amplified analogue audio output
volume. The LEDs will illuminate progressively to indicate the current
volume level.
7IR Window: Accepts IR signals from the included IR remote for control
of this unit, IR bypass, and to activate the transmission of learned IR
codes.
8SERVICE Port: This port is reserved for firmware update use only.
6.2 Matrix Rear Panel
RS-232
LINE OUT
CONTROL DC 24V
ZONE B
CAT5e/6/7 OUT
–
LEFT
+
34
12
HDMI IN
CAT5e/6/7 OUT
ZONE A
HDMI OUT
RIGHT
+–
345
12
IR OUT
1
5 6 7 8
2 3 4 9
1HDMI IN 1~4 Ports: Connect to HDMI source equipment such as
media players, game consoles or set-top boxes.
2ZONE A CAT5e/6/7 & HDMI Ports:
CAT5e/6/7 OUT: Connect to a compatible HDBaseT Receiver with a
single Cat.5e/6/7 cable for transmission of all data signals. 48V PoH
will also be supplied to a connected compatible PD Receiver.
HDMI OUT: Connect to an HDMI TV, monitor or amplifier for digital
video and audio output.
3ZONE B CAT5e/6/7 Port: Connect to a compatible HDBaseT Receiver
with a single Cat.5e/6/7 cable for transmission of all data signals. 48V
PoH will also be supplied to a connected compatible PD Receiver.
4CONTROL Port: Connect to the local network through a network
switch or router to control the unit via Telnet, WebGUI, or mobile
device app.
5IR OUT 1~5 Ports: Connect to the provided IR Blasters to transmit IR
signals to devices within direct line-of-sight of the IR Blasters.

11
6RS-232 Port: Connect directly to a PC, laptop or other serial control
device to send RS-232 commands to control the unit.
7LINE OUT Port: Connect to powered speakers, headphones, or an
amplifier for stereo analogue audio output.
8RIGHT/LEFT Ports: Connect to unpowered 4Ω speakers for stereo
analogue audio output. Up to 20W of power is provided to each
speaker channel.
9DC 24V Port: Plug the 24V DC power adapter into this port and
connect it to an AC wall outlet for power.
6.3 Receiver Front Panel

RS-232 OUT
ISP
LINK
PWR
STD
UPDATE
SYNC
HQ/STD
PUV-1710LRX-AVLC
1 2 3 4
1ISP: This button is reserved for factory use only.
2STD/UPDATE: This switch is reserved for factory use only. The default
setting is “STD”.
3RS-232 OUT: Connect to a serial controllable device for the extension
of RS-232 signals.
4SYNC LED: This LED will illuminate when a live input source is
detected.
HQ/STD LED: This LED will illuminate whenever the AVLC function is
active. A green LED indicates that AVLC is in HQ (High Quality) mode.
A red LED indicates that AVLC is in STD (Standard) mode.
POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
LINK LED: This LED will illuminate solidly when a live connection
with a compatible Receiver is active. The LED will blink with a regular
pattern if a Receiver is connected but there is not currently a live
signal. The LED will blink with an irregular pattern if a connection error
has occurred.

12
6.4 Receiver Rear Panel
IR1
EXTENDER CAT5e/6/7 IN HDMI OUT
IR2
BLASTER
1 2 34
1IR2 BLASTER: Connect to the provided IR Blaster to transmit IR signals
to devices within direct line-of-sight of the IR Blaster.
2IR1 EXTENDER: Connect to the provided IR Extender to extend the
IR control range of remotely located devices. Ensure that the remote
being used is within direct line-of-sight of the IR Extender.
3CAT5e/6/7: Connect to a compatible HDBaseT Transmitter with a
single Cat.5e/6/7 cable for transmission of all data signals.
4HDMI OUT: Connect to an HDMI TV, monitor or amplier for digital
video and audio output.

13
6.5 Remote Control
6.5.1 IR Remote (Unit Control)
This unit’s IR remote provides control
over the unit directly, as well as control
over additional external devices through
the assignment of learned IR commands.
The following buttons, in “Standard”
mode provide direct control over the
unit itself. Switching to“Advanced” mode
allows these buttons to also be used to
control external device functions.
1POWER Button: Press and hold this
button for over 3 seconds to power
the unit on or place it into standby
mode.
Note: A short press of this button will
send a user defined IR command to the
current source device.
2ADV. Button: Pressing this button
toggles the unit between using the
“Standard” and “Advanced” IR remote
button definitions.
3ZONE A & ZONE B IN 1~4 Buttons: Press any of these buttons to
switch immediately to the corresponding input for display in Zone A
or Zone B respectively.
4AUDIO Buttons
SOURCE Button: Press this button to sequentially switch through the
available audio sources for both analogue outputs.
MUTE Button: Press to toggle between muting and unmuting the
analogue audio output.
Note: By default, the mute button only controls the amplified output. This
behavior can be adjusted via RS-232.
VOL+/VOL− Buttons: Press these buttons to increase or decrease the
amplified analogue audio output volume.
123
456
789
0
Adv.
1
34
2

14
6.5.2 IR Remote (Assignable Buttons)
Standard Mode
The function of the buttons on the bottom half of the
IR remote are user defined within the WebGUI. They
are used to tell the unit to transmit IR commands to
the source device currently being viewed in the user’s
current Zone location.
For example, if the user is watching Input 3 while in
Zone A, then pressing any of these buttons will send
the associated user-defined commands to the device
connected to Input 3 via the IR Blaster connected to
IR Output 3. If the user then moves to Zone B, which is
watching Input 2, and presses the same buttons, the
unit will send commands associated with Input 2 via
the IR Blaster connected to IR Output 2.
1) Zone A Mirrored Outputs (HDBaseT)
Source 3
RS-232 OUT
ISP
LINK
PWR
STD
UPDATE
SYNC
HQ/STD
PUV-1710LRX-AVLC
1 2 3
4 5 6
7 8 9
0
Adv.
1234 1234
ZONE
BAARC
IR SERVICEZONE AZONE BAUDIO SELECT MUTE Vol –Vol +POWER
MA-421
Source 1 Source 2 Source 3 Source 4
HDBaseT
Output
UHDTV
IR Control of
Input 1~4

15
2) Zone A Mirrored Outputs (HDMI)
Source 3
1 2 3
4 5 6
789
0
Adv.
1234 1234
ZONE
BAARC
IR SERVICEZONE AZONE BAUDIO SELECT MUTE Vol –Vol +POWER
MA-421
Source 1 Source 2 Source 3 Source 4
HDMI
Output
UHDTV
IR Control of
Input 1~4
3) Zone B Output (HDBaseT)
Source 2
RS-232 OUT
ISP
LINK
PWR
STD
UPDATE
SYNC
HQ/STD
PUV-1710LRX-AVLC
1 2 3
4 5 6
7 8 9
0
Adv.
1234 1234
ZONE
BAARC
IR SERVICEZONE AZONE BAUDIO SELECT MUTE Vol –Vol +POWER
MA-421
Source 1 Source 2 Source 3 Source 4
HDBaseT
Output
UHDTV
IR Control of
Input 1~4

16
Advanced Mode
If the “Adv.”button is pressed, the unit will switch
into the “Advanced” IR command mode, changing
the functionality of these buttons to use additional
IR commands that have been defined by the user
within the WebGUI. Similar to the other user defined
buttons, they are used to tell the unit to transmit IR
commands to the source device currently being viewed
in the user’s current Zone location. Buttons that have
Advanced mode functionality are easily identified by
their alternative coloring.
Note: For detailed information about assigning user
defined IR commands within the WebGUI, please refer to
Section 6.9.5.
123
456
789
0
Adv.

17
6.6 IR Cable Pinouts
IR Blaster
Cabl
e
1
2
3
Infrared
Power
Not U
sed
IR Extender
Cabl
e
1
2
3
Infr
ared
Power
Ground
6.7 RS-232 Bypass Pinout
1
2
3
4
5
8
7
6
9
DCD
RxD
TxD
DTR
GND
RI
CTS
RTS
DSR
DE-9
Female Port
DCD
RxD
TxD
DTR
GND
RI
CTS
RTS
DSR
1
2
3
4
5
8
7
6
9
DE-9 Male
Port
6.8 Serial Control
Serial Port Default Settings
Baud Rate 19200
Data Bits 8
Parity Bits None
Stop Bits 1
Flow Control None

18
6.9 WebGUI Control
Device Discovery
Please obtain the “Device Discovery” software from your authorised dealer
and save it in a directory where you can easily nd it.
Connect the unit and your PC/Laptop to the same active network and
execute the “Device Discovery” software. Click on “Find Devices on
Network” and a list of devices connected to the local network will show
up indicating their current IP address.
By clicking on one of the listed devices you will be presented with the
network details of that particular device.
1) IP Mode: If you choose, you can alter the static IP network settings for
the device, or switch the unit into DHCP mode to automatically obtain
proper network settings from a local DHCP server. To switch to DHCP
mode, please select DHCP from the IP mode drop-down, then click
“Save” followed by “Reboot”.
2) WebGUI Hotkey: Once you are satised with the network settings,
you may use them to connect via Telnet or WebGUI. The network
information window provides a convenient link to launch the WebGUI
directly.

19
WebGUI Overview
After connecting to the WebGUI’s address in a web browser, the login
screen will appear. Please enter the appropriate user name and password
then click “Enter” to log in.
Note: The default user name and password is “admin”.
On the left side of the browser you will see the following menu tabs
where all primary functions of the unit are controllable via the built in
WebGUI. The individual functions will be introduced in the following
sections.
Clicking the “Logout” tab will automatically log the currently connected
user out of the WebGUI and return to login page.

20
6.9.1 Video Switch Tab
This tab provides A/V routing control, auto switch controls, and I/O
renaming options.
To assign a new A/V route, please click the button of the Zone you wish
to send video/audio to on the left and then click on the button of the
preferred Input port on the right. Selecting both Zones is possible.
As you select each button they will become outlined in white. The new
route will become active immediately and the routing information
displayed on the buttons will change accordingly.
Note: Both outputs included in Zone A (HDBaseT and HDMI) will always show
the same source.
1) Zone A/B: Buttons for selecting the Output Zone (A or B) to route A/
V Inputs to. Details about the Output names and currently selected
Input are also displayed here. Clicking on the gear icon ( ) opens up
the Zone Edit window.
2) Input 1/2/3/4: Buttons for selecting the HDMI Input (1 through 4) to
route to the selected Zone. Details about the Input names and current
sync status are also displayed here. Clicking on the gear icon ( )
opens up the Input Edit window.