Cypress Semiconductor CY25822-2 User manual

CK-SSC Spread Spectrum Clock Generato
r
CY25822-
2
Cypress Semiconductor Corporation • 3901 North First Street • San Jose, CA 95134 • 408-943-2600
Document #: 38-07531 Rev. ** Revised March 18, 2003
Features
• 3.3V operation
• 48- and 66-MHz frequency support
• Selectable slew rate control
• 350-pS jitter
•I
2C programmability
• 500-µA power-down current
• SpreadSpectrumforbestelectromagneticinterference
(EMI) reduction
• 8-pin SOIC package
Block Diagram
Pin Configuration
1
2
3
4
8
7
6
5
CLKIN
VDD
GND
*PWRDWN#
SCLOCK
SDATA
REFOUT
CY25822-2
CLKOUT
* 150KΩ Pull-up
Freq. Phase
Modulating
VCO Post CLKOUT
Detector Charge
Pump
Waveform
DividersDivider
Feedback
Divider
PLL
GND
VDD
Σ
M
N
Clock Input (SSCG Output)
REFOUT
Logic
Control
SDATA
SCLOCK
PWRDWN#
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 2 of 9
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions such as individual
clock output buffers, etc., can be individually enabled or
disabled.
The registers associated with the Serial Data Interface
initializes to their default setting upon power-up, and therefore
use of this interface is optional. Clock device register changes
are normally made upon system initialization, if any are
required. The interface can also be used during system
operation for power management functions.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operation from the controller. For
block write/read operation, the bytes must be accessed in
sequential order from lowest to highest byte (most significant
bit first) with the ability to stop after any complete byte has
been transferred. For byte write and byte read operations, the
system controller can access individual indexed bytes. The
offset of the indexed byte is encoded in the command code, as
described in Table 1.
The block write and block read protocol is outlined in Table 2
while Table 3 outlines the corresponding byte write and byte
read protocol.The slave receiver address is 11010100 (D4h).
Pin Description
Pin No. Pin Name Pin Type Pin Description
1 CLKIN Input 48-MHz or 66-MHz Clock Input.
2 VDD Power Power Supply for PLL and Outputs.
3 GND Ground Ground for Outputs.
4 CLKOUT Output 48-MHz or 66-MHz Spread Spectrum Clock Output.
5REFOUTOutputNon-spread Spectrum Reference Clock Output.
6 SDATA I/O I2C-compatible SDATA.
7 SCLOCK Input I2C-compatible SCLOCK.
8 PWRDWN# Output LVTTL Input for PowerDown# Active Low.
Table 1. Command Code Definition
Bit Description
7 0 = Block read or block write operation
1 = Byte read or byte write operation
(6:0) Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be ’0000000’
Table 2. Block Read and Block Write Protocol
Block Write Protocol Block Read Protocol
Bit Description Bit Description
1Start 1Start
2:8 Slave address – 7 bits 2:8 Slave address – 7 bits
9 Write = 0 9 Write = 0
10 Acknowledge from slave 10 Acknowledge from slave
11:18 Command Code – 8 bits
'00000000' stands for block operation 11:18 Command Code – 8 bits '00000000' stands for block operation
19 Acknowledge from slave 19 Acknowledge from slave
20:27 Byte Count – 8 bits 20 Repeat start
28 Acknowledge from slave 21:27 Slave address – 7 bits
29:36 Data byte 1 – 8 bits 28 Read = 1
37 Acknowledge from slave 29 Acknowledge from slave
38:45 Data byte 2 – 8 bits 30:37 Byte count from slave – 8 bits
46 Acknowledge from slave 38 Acknowledge
.... ...................... 39:46 Data byte from slave – 8 bits
.... Data Byte (N–1) –8 bits 47 Acknowledge
.... Acknowledge from slave 48:55 Data byte from slave – 8 bits
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 3 of 9
.... Data Byte N –8 bits 56 Acknowledge
.... Acknowledge from slave .... Data bytes from slave/Acknowledge
.... Stop .... Data byte N from slave – 8 bits
.... Not Acknowledge
.... Stop
Table 2. Block Read and Block Write Protocol (continued)
Table 3. Byte Read and Byte Write Protocol
Byte Write Protocol Byte Read Protocol
Bit Description Bit Description
1Start 1Start
2:8 Slave address – 7 bits 2:8 Slave address – 7 bits
9 Write = 0 9 Write = 0
10 Acknowledge from slave 10 Acknowledge from slave
11:18 Command Code – 8 bits
'1xxxxxxx' stands for byte operation, bits[6:0] of
the command code represents the offset of the
byte to be accessed
11:18 Command Code – 8 bits
'1xxxxxxx' standsfor byteoperation, bits[6:0]
of the command code represents the offset of
the byte to be accessed
19 Acknowledge from slave 19 Acknowledge from slave
20:27 Data byte from master – 8 bits 20 Repeat start
28 Acknowledge from slave 21:27 Slave address – 7 bits
29 Stop 28 Read = 1
29 Acknowledge from slave
30:37 Data byte from slave – 8 bits
38 Not Acknowledge
39 Stop
Byte 0: Control Register
Bit @Pup Pin# Name Pin Description
714SS0 –
604SS1 –
504SS2 –
404SS3 –
3 1 Not Applicable Reserved, must be written as 1
214,5CLKOUT,
REFOUT Power-down three-state enable 0 = three-state outputs, 1 = drive outputs low
(Applies only in Power Down State)
1 1 4 CLKOUT Spread Spectrum enable
0 = spread off, 1 = spread on
0 0 Not Applicable No Pins
Table 4. Spread Spectrum Select
SS3 SS2 SS1 SS0 Spread Mode Spread Amount%
0 0 0 0 Down 0.8
0 0 0 1 Down 1.0
0 0 1 0 Down 1.25
0 0 1 1 Down 1.5
0 1 0 0 Down 1.75
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 4 of 9
Bytes 2 through 5: Reserved Registers PWRDWN# (Power-down) Clarification
The PWRDWN# (Power-down) pin is used to shut off ALL
clocks prior to shutting off power to the device. PWRDWN# is
an asynchronous active LOW input. This signal is synchro-
nized internally to the device powering down the clocksynthe-
sizer.PWRDWN#isanasynchronousfunctionforpoweringup
the system. When PWRDWN# is low, all clocks are driven to
a LOW value and held there and the VCO and PLLs are also
powered down. All clocks are shut down in a synchronous
manner so has not to cause glitches while transitioning to the
low ‘stopped’ state. When PWRDWN# is deasserted the
clocks should remain stopped until the VCO is stable and
within specification (tSTABLE). A stopped clock is either
tri-stated or driven low depending on the state of the tri-state
enable I2C register bit. CY25822 clocks that are stopped in the
driven state are driven low.
The CLKIN input must be on and within specified operating
parameters before PWRDWN# is asserted and it must remain
in this state while PWRDWN# is asserted.
0 1 0 1 Down 2.0
0 1 1 0 Down 2.5
0 1 1 1 Down 3.0
1000 Center ±0.3
1001 Center ±0.4
1010 Center ±0.5
1011 Center ±0.6
1100 Center ±0.8
1101 Center ±1.0
1110 Center ±1.25
1111 Center ±1.5
Table 4. Spread Spectrum Select (continued)
SS3 SS2 SS1 SS0 Spread Mode Spread Amount%
Byte 1: Control Register
Bit @Pup Pin# Name Pin Description
7 1 5 REFEN REFOUT enable
0 = disabled, 1 = enabled
6 1 5 REFSLEW REFOUT edge rate control
0 = slow, 1 = nominal
5 0 Not Applicable Reserved.
4 0 Not Applicable Reserved
3 1 4 CLKSLEW CLKOUT edge rate control
0 = slow, 1 = nominal
2 1 4 CLKEN CLKOUT enable
0 =disabled, 1 = enabled
1 0 Not Applicable Reserved
0 0 Not Applicable Reserved
Byte 6: Vendor/Revision ID Register
Bit @Pup Pin# Name Pin Description
7 0 – – Revision ID Bit 3
6 0 – – Revision ID Bit 2
5 0 – – Revision ID Bit 1
4 0 – – Revision ID Bit 0
3 1 – – Vendor ID Bit 3
2 0 – – Vendor ID Bit 2
1 0 – – Vendor ID Bit 1
0 0 – – Vendor ID Bit 0
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 5 of 9
CLKOUT and REFOUT Enable Clarification
TheCLKOUTenableandREFOUTenableI2Cregisterbitsare
used to shot-off the CLKOUTand REFOUTclocks individually.
The VCO and crystal oscillator must remain on. A shutdown
clock is driven low. ALL clocks need to be stopped in a
predictable manner. All clocks need to be shutdown without
any glitches or other abnormal behavior while transitioning to
a stopped state. Similarly when CLKOUT or REFOUT is
enabled the clock must start in a predictable manner without
any glitches or abnormal behavior.
REFOUT
PWRDWN#
CLKOUT
Figure 1. Power-down Assertion
PD#
CLKOUT
REFOUT
<3.0ms
Figure 2. Power-down Deassertion
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 6 of 9
Table 5. Absolute Maximum Ratings
Parameter Description Condition Min. Max. Unit
VDD Core Supply Voltage –0.5 4.6 V
VDD_A Analog Supply Voltage –0.5 4.6 V
VIN Input Voltage Relative to V SS –0.5 VDD + 0.5 VDC
TSTemperature, Storage Non Functional –65 +150 °C
TATemperature, Operating Ambient Functional 0 70 °C
TJTemperature, Junction Functional – 150 °C
ESDHBM ESD Protection (Human Body Model) MIL-STD-883, Method 3015 2000 – Volts
UL–94 Flammability Rating @1/8 in. V–0
MSL Moisture Sensitivity Level 1
Table 6. DC Parameters (TA= 0°C to +70°C, VDD = 3.3V ± 5%)
Parameter Description Condition Min. Max Unit Notes
VDD Supply Voltage – 3.135 3.465 V VDD = 3.3 ± 5%
VIH Input High Voltage – 2.0 VDD + 0.3 V
VIL Input Low Voltage – VSS – 0.3 0.8 V
IIL1 Input Leakage Current SCLOCK
or SDATA –25 +25 µA
IIL2 Input Leakage Current PWRDWN# –75 –15 µA
VOH Output High Voltage IOH = –4 mA 2.4 – V Single edge is required to
be monotonic when transi-
tioningthroughthis region.
VOL Output Low Voltage IOL = 4 mA – 0.4 V Single edge is required to
be monotonic when transi-
tioningthroughthis region.
CIN Input Pin Capacitance – – 5 pF
COUT Output Pin Capacitance – – 6 pF
LIN Pin Inductance – – 7 nH
TAAmbient Temperature – 0 70 °C No air flow
IDD1 Supply Current @ 66 MHz – 50 mA
IDD2 Supply Current @ 48 MHz – 40 mA
IPD Power Down Supply Current – – 500 µA
Table 7. AC Parameters (TA= 0°C to +70°C, VDD = 3.3V ± 5%)
Parameter Description Conditions Min. Max. Unit Notes
tHIGH CLK High Time, 48MHz Measured @2.4V 9.45 10.95 ns Specification applies to
48MHz output mode.
tLOW CLK, Low Time, 48MHz Measured @0.4V 8.50 10.10 ns Specification applies to
48MHz output mode.
tHIGH CLK High Time, 66MHz Measured @2.4V 6.85 7.90 ns Specification applies to
66.7MHz output mode.
tLOW CLK Low Time, 66MHz Measured @0.4V 5.95 6.95 ns Specification applies to
66.7MHz output mode.
tRISEH1 Rising Edge Rate Measured from 0.4V to 2.4V
REFOUT and CLOCKOUT 2.0 5.0 V/ns High Buffer Strength Refer to I2C Control
tFALLH1 Falling Edge Rate Measured from 2.4V to 0.4V
REFOUT and CLOCKOUT 2.0 5.0 V/ns High Buffer Strength Refer to I2C Control
tRISEL1 Rising Edge Rate Measured from 0.4V to 2.4V
REFOUT and CLOCKOUT 1.33 4.0 V/ns Low Buffer Strength Refer to I2C Control
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 7 of 9
tFALLL1 Falling Edge Rate Measured from 2.4V to 0.4V
REFOUT and CLOCKOUT 1.33 4.0 V/ns Low Buffer Strength Refer to I2C Control
tRISEH2 Rise Time Measured from 0.4V to 2.4V
REFOUT and CLOCKOUT 0.4 1.0 ns High Buffer Strength Refer to I2C Control
tFALLH2 Fall Time Measured from 2.4V to 0.4V
REFOUT and CLOCKOUT 0.4 1.0 ns High Buffer Strength Refer to I2C Control
tRISEL2 Rise Time Measured from 0.4V to 2.4V
REFOUT and CLOCKOUT 0.5 1.5 ns Low Buffer Strength Refer to I2C Control
tFALLL2 Fall Time Measured from 2.4V to 0.4V
REFOUT and CLOCKOUT 0.5 1.5 ns Low Buffer Strength Refer to I2C Control
TCYC1 Cycle to Cycle Jitter REFOUT – 500 ps SSCG is ON
TCYC2 Cycle to Cycle Jitter CLOCKOUT – 250 ps SSCG is ON
LTJ 10µS Period Jitter
(100KHz,FrequencyMod-
ulation Amplitude)
Applies to REFOUT at all
timesandCLOCKOUTwhen
SSCG is Off
–2.0ns –
tSTART Start up time From VDD = 2.0 V – 3.0 ms All outputs disabled
Table 7. AC Parameters (TA= 0°C to +70°C, VDD = 3.3V ± 5%) (continued)
Parameter Description Conditions Min. Max. Unit Notes
Table 8. Signal Loading Table
Clock Name Max Load (pF)
CLKOUT, REFOUT 15
Ordering Information
Part Number Package Type Product Flow
CY25822SC–2 8-pin SOIC Commercial, 0°C to 70°C
CY25822SC–2T 8-pin SOIC – Tape and Reel Commercial, 0°C to 70°C
[+] Feedback

CY25822-
2
Document #: 38-07531 Rev. ** Page 8 of 9
© Cypress Semiconductor Corporation, 2003. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nordoes it convey or implyany license underpatent or otherrights. Cypress Semiconductordoes not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
Package Diagram
Purchase of I2C components from Cypress, or one of its sublicensed Associated Companies, conveys alicense under thePhilips
I2C Patent Rightsto use these components in an I2Csystem, provided that the system conforms to the I2CStandardSpecification
as defined by Philips.All product and company names mentioned in this document are trademarks of their respective holders.
8-lead (150-Mil) SOIC – S8
51-85066-*B
[+] Feedback

CY25822
-2
Document #: 38-07531 Rev. ** Page 9 of 9
Document History Page
Document Title: CY25822-2 CK-SSC Spread Spectrum Clock Generator
Document Number: 38-07531
REV. ECN NO. Issue Date Orig. of Change Description of Change
** 124462 03/19/03 RGL New Data Sheet
[+] Feedback