Cypress Semiconductor CY8CKIT-036 User manual

CY8CKIT-036 THERMAL MANAGEMENT KIT
QUICK START GUIDE
3-pin header to choose between a single-sensor or a dual-sensor (daisy-chain)
connection for the PWM temperature sensors. Place jumper in 1-2 position
to enable dual-sensor daisy-chain mode
Kit Contents:
1) Thermal Management Board
2) Power DC Adaptor 12 V/2 A
3) Quick Start Guide
3-pin header to set logic signal levels for digital temperature sensors.
Place in 2-3 position for 3.3-V interfacing (and the kit projects)
3-pin header for fan power supply. Place in 1-2 position to source
external power from the power jack (J13)
Note:
This Kit is designed to work with the following PSoC®Development Kits:
If you are using a PSoC 4 Pioneer Kit (CY8CKIT-042), you will require a PSoC Adapter Shield Kit (CY8CKIT-019) to
connect the Thermal Management Kit (CY8CKIT-036)
SINGLE
PWM_TMP
DUAL
3.3 V VDDIO 5 V
12 V_DVK 12 V 12 V_EXT
J2
Jumper Default Setting Description
J3
J9
Please ensure the following settings in CY8CKIT-019:
1) Jumpers: Ensure the settings of J5, J6, J7 are compatible
with CY8CKIT-036, as shown in the image
2) Connect a wire from pin 10 of header J9 to pin 1 of header J2
(this is to connect the potentiometer input)
Fan Socket
Temperature
Sensor with
I2C Interface
Temperature
Sensor with
One-wire Interface
Temperature Sensor
with a PWM Output
Diode
Temperature Sensors
I2C Connector
1 2 3
CY8CKIT-036 THERMAL MANAGEMENT KIT
QUICK STARTGUIDE
3-pin header to choose between single sensor or dual sensor (daisy-chain)
connection for the PWM temperature sensors. Place jumper in 1-2 position
to enable dual sensor daisy-chain moder 3.2
Kit Contents:
1) Thermal Management board
2) Power DC Adaptor 12V/2A
3) Quick Start Guide
3-pin header to set logic signal levels for digital temperature sensors.
Place in 1-2 for 5V interfacing. Place in 2-3 position for 3.3V interfacing
3-pin header for fan power supply. Place in 1-2 position to source external
power from the power jack (J13). Place in 2-3 position to source 12V
power from your PSoC development kit
Note:
This Kit is designed to work with a PSoC Development Kit like:
PSoC Development Kit: CY8CKIT-001
PSoC 3 Development Kit: CY8CKIT-030
PSoC 5LP Development Kit: CY8CKIT-050
PSoC 4 Pioneer Kit: CY8CKIT-042
If you are using a PSoC 4 Pioneer Kit (CY8CKIT-042), you will require a PSoC Adapter Shield Kit (CY8CKIT-019) to
connect the Thermal Management Kit (CY8CKIT-036).
SINGLE
PWM_TMP
DUAL
3.3V VDDIO 5V
12V_DVK 12V 12V_EXT
J2
JUMPER DEFAULTSETTING DESCRIPTION
J3
J9
Please ensure the following settings in CY8CKIT-019:
1) Jumper: Ensure the settings of J5, J6, J7 is compatible to work
with CY8CKIT-036 as shown in the image below
2) Connect a wire from pin 10 of header J9 to pin 1 of header J2
(this is for connecting the potentiometer input)
FanSocket
Temperature
Sensorwith
I2Cinterface
Temperature
Sensorwith
One-wireinterface
TemperatureSensor
witha PWM output Diode
TemperatureSensors
I2CConnector
1 2 2
PSoC 5LP Development Kit: CY8CKIT-050
PSoC 4 Pioneer Kit: CY8CKIT-042
PSoC Development Kit: CY8CKIT-001
PSoC 3 Development Kit: CY8CKIT-030

QUICK START GUIDE
Set 'VDD DIG' and 'VDD ANLG' to 3.3 V using
SW3, J6 and J7 on the CY8CKIT-001. Set J8 to VREG
Ensure the LCD Power jumper (J12) is set to ON and
the LCD is plugged into CY8CKIT-001. Connect
jumper J11 to enable power to the potentiometer
Set 'VDDD' and 'VDDA' to 3.3 V by placing jumpers in the
1-2 position of J10 and J11. Enable POT_PWR by installing
a jumper on J30 of the kit
CY8CKIT-001
If you are using:
Before you start, check these settings in your PSoC Development Kit
Check for:
CY8CKIT-030 or
CY8CKIT-050
PSOC®1/PSOC 3/ PSOC 5LP USERS
• Open the PSoC Programmer software in your computer
- Go to Start > All Programs > Cypress >
PSoC Programmer
• Open the Thermal Management project hex le in the
PSoC Programmer software
• Refer to the table above to select the correct hex le for
your development kit
1 2
3 4
• Download and Install the latest kit software and
examples from www.cypress.com/go/CY8CKIT-036
• Connect your Cypress Programmer
- If you are using a CY8CKIT-001, connect the
MiniProg3 to the PSoC processor module.
- If you are using a CY8CKIT-030 (PSoC 3) or
CY8CKIT-050 (PSoC 5LP), connect the USB cable
to the onboard programmer
Product Family Development Kit Hex File name File Path
PSoC 1 CY8CKIT-001 CY8CKIT-001_P1.Hex <Installation Directory>\PSoC 1 Thermal
Management EBK\<version>\HexFiles
CY8CKIT-030 CY8CKIT-030_P3.Hex
CY8CKIT-001 CY8CKIT-001_P3.Hex
CY8CKIT-050 CY8CKIT-050_P5LP.Hex
CY8CKIT-001 CY8CKIT-001_P5LP.Hex
PSoC 3
PSoC 5LP
<Installation Directory>\PSoC3_5 Thermal
Management EBK\<version>\HexFiles

PSOC®1/PSOC 3/ PSOC 5LP USERS
QUICK START GUIDE
• Select the following parameters in the PSoC programmer:
For PSoC 1 Users:
1. Programming mode as ‘Reset’
2. Protocol as ‘ISSP’
3. Voltage as ‘3.3 V’
• Click the ‘Program’ button in the PSoC Programmer software
• The PSoC programmer will indicate successful programming in the status window
For PSoC 3 / PSoC 5LP Users:
4. Programming mode as ‘Reset’
5. Protocol as ‘SWD’
6. Voltage as ‘3.3 V’
5
Parameter settings for PSoC 1 Users
CY8CKIT-001 CY8CKIT-030 or
CY8CKIT-050
LCD Output
CY8CKIT-001
Parameter settings for PSoC 3 / PSoC 5LP
• Connect J14 of the CY8CKIT-036 to:
- Port A of CY8CKIT-001
or
- Port E of CY8CKIT-030 or CY8CKIT-050
• Connect the power cable to the kits
• View the output in the display showing the temperature
reading and the fan speed
• Use SW1 (in CY8CKIT-001) or SW2 (in CY8CKIT-030/
CY8CKIT-050) to navigate between the thermal
management screens on the LCD
• Refer to the User Guide to learn more about the kit and
the solutions
67
CY8CKIT-030 or
CY8CKIT-050

© 2013 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the properties of their respective owners.
Doc.#: 001-89888 Rev.**
QUICK START GUIDE
For the latest information about this kit and to download kit software and hardware les,
visit http://www.cypress.com/go/CY8CKIT-036
• Connect the USB cable to the onboard programmer of
the PSoC 4 Pioneer Kit
• Place a jumper in position 1-2 of J9
2
• Connect the PSoC Shield (CY8CKIT-019) to the PSoC
Pioneer Kit (CY8CKIT-042). Then, connect the Thermal
Management Kit (CY8CKIT-036) to the PSoC Shield
(CY8CKIT-019)
• Connect the 12-V/2-A power adapter to the power
jack J13 of the Thermal Management Kit (CY8CKIT-036)
• You will see the fans rotating at a speed set by the thermal
algorithms running in PSoC 4. You can vary the fan
speed by adjusting the potentiometer (on CY8CKIT-019)
• Refer to the application note (AN89346) documentation
to learn more about the projects, the thermal algorithms,
and the kit
3
• Select the parameters in the PSoC Programmer, as shown
in the gure above
• Click the ‘Program’ button and view the status message
indicating successful programming
4
6
PSOC 4 USERS
PSoC Programmer Software Parameter settings in PSoC Programmer
Application Note
• Download and install PSoC Creator software from
www.cypress.com/go/CY8CKIT-036
•
Download the application note (AN89346) pdf document
and the zip le (which includes the example project les).
Unzip the le and save the folder to your preferred directory
• Open the PSoC Programmer software
• Go to Start > All Programs > Cypress > PSoC Programmer
• Open the Thermal Management project hex le from the
downloaded application note folder
1
5
Application Note
File path: Install_directory>:
\AN89346\HexFiles
\Thermal_Management_Project.hex