Cypress TRAVEO II CPU BOARD User manual

CYTVII-B-H-8M-176 CPU BOARD QUICK START GUIDE
TRAVEO II CPU BOARD
Kit Contents:
1. Traveo II CPU Board CYTVII-B-H-8M-176 CPU BOARD
2. Type-B Mini USB Cable
3. 12V AC-DC Universal Power Adapter
4. Quick Start Guide (this document)
5. Screws and Spacers

TRAVEO II CPU BOARD
• Ensure that the MCU Reset Controller Jumper (J18) is
inserted
CYTVII-B-H-8M-176 CPU BOARD QUICK START GUIDE
•Ensure that jumpers J7, J6, J5, J11, J9, J41, J42 are
inserted. Ensure that Jumpers J8, J45, J10 are in
1-2 position and J46 is in 2-3 position
•Connect an appropriate programming tool (IAR/GHS), to
one of the debugging interfaces -(J21, J20, J22, J19)
Use an appropriate IDE on a PC, to load a rmware SREC le into the device ash successfully.
The LED Blink Firmware is available in the Release-Package
• Connect the 12V Adapter to Power Jack (J1). Toggle the
switch SW1 to ON position to power up the board
12
4
3

CYTVII-B-H-8M-176 CPU BOARD QUICK START GUIDE
For the following documentation:
• User Guide
•Schematic
• Sample Driver Library (SDL)
• Software examples
Please use the Cypress Customer Support Portal.
Instructions:
•The Traveo II CPU Board can be used standalone to evaluate limited features of the Traveo II MCU
•The board can be used with Body Controller Base Board, to evaluate all the features of the MCU
TRAVEO II CPU BOARD
•To know more about the Base Board and compatibility, please use the Cypress Customer
Support Portal. (cypress.com/support)

© 2019 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the property of their respective owners.
002-27891 Rev.**
CYTVII-B-H-8M-176 CPU BOARD QUICK START GUIDE
TRAVEO II CPU BOARD
Traveo II CPU Board Details
1. MCU Reset Controller Jumper - J18
2. MCU Reset LED – LED6
3. MCU Reset Button - SW5
4. User LED’s - LED4 & LED5
5. Jumpers for User LEDs - J16 & J17
6. Automotive Ethernet Controller
7. D-SUB 9 Automotive Ethernet Connector
8. Hibernate Wake Up Switch – SW3
9. 20 Pin IDC Arm Standard JTAG Connector
10. MIPI-10-Cortex Debug Connector
11. MIPI-20-Cortex Debug + ETM Connector
12. Mictor-38- Arm ETM Mictor Connector
13. User Switches – SW2 & SW4
14. Jumpers for User Switches – J13 & J15
15. Jumpers for SMIF
16. Jumpers for SDHC
17. 512Mb Hyper Flash Memory
18. 64Mb HyperRAM Self-Refresh DRAM
19. Quad SPI 256Mb Flash Memory
20. SD Card Connector
21. 1.8V LDO
22. Audio Jack – J29
23. Audio Codec
24. USB Type-B Mini Connector
25. UART Rx and Tx LEDs
26. SW1 – Power Switch
27. Power Jack (12V) – J1
28. Cypress USB Serial Controller
29. UART Rx and Tx Jumpers
30. Cypress PMIC Board
31. Cypress TVII-B-H-8M Device
32. MCU Power Jumpers
33. MCU Power LEDs
1
2
3
4
5
6
7
8
9
10
11 12 13 14 171615 18 19
20
21
22
23
24
25
26
27
282930313233