NXP Semiconductors S12VR32EVB User manual

Quick Start Guide
S12VR32EVB
Highly Integrated Microcontroller
Power Window Lift Relay-Based

2 3
Quick Start Guide www.nxp.com
GET TO KNOW THE S12VR32EVB BOARD SIMPLIFIED BOARD DESCRIPTION
Front side of S12VR32EVB board
User
Button
Hall Sensor
Connector
Relay
Motor
Out (2)
LIN Interface
and Power
Supply
Reset
Button
BDM
Connector
User Up/Stop/
Down Switch
External
Temperature
Sensor

4 5
Quick Start Guide www.nxp.com
2Open the Application
Software
Download and open the file up-down-
no-antipinch.mcpwith CodeWarrior
Development Studio for HCS12(X).
3Connect the
Board
Connect a 12 V automotive battery and
a brushed DC motor to the board. For
details, refer to the section titled, “Step-
By-Step Board Connection.”
4Download the Software to
the S12VR64 MCU Flash
Connect an HCS12(X) external debugger
to the computer and then connect the
debugger to J6. Follow the operating
system messages to install the debugger
drivers. Flash the application by pressing
the debug button on CodeWarrior.
Follow the debugger instructions to flash
the MCU.
INTRODUCTION SOFTWARE TOOLS INSTALLATION
The S12VR32 EVB features the S12VR32 microcontroller, an automotive 16-bit MCU
for applications based on motor control relays. The S12VR32 evaluation board
integrates an S12 CPU, a LIN physical interface, a 5 V regulator system to supply the
microcontroller and low-side drivers to control the relay.
This ultra-low-cost development platform also includes a Hall sensor interface, an
external 16 MHz oscillator, a switch button and an onboard OSBDM.
1Install CodeWarrior®5.1
Development Studio
CodeWarrior is a complete
integrated development
environment (IDE) that provides
a highly visual and automated
framework.
Download the CW5.1 from
nxp.com/codewarrior.

Quick Start Guide www.nxp.com
6 7
STEP-BY-STEP BOARD CONNECTION STEP-BY-STEP BOARD CONNECTION (CONT.)
1Connect
the Board
Supply your board with 12 V as is shown
in the image.
2Connect
the Motor
Connect your DC motor as is shown in
the image.
3Connect an External
HCS12(X) Debugger 4Connect the Hall Sensor Connector
Connect the Hall encoder (Only required
for anti pinch applications.)
LIN Bus
0V 12V
Battery
V0 V1 DIRECTION
12V 0V Up
0V 12V Down
0V 0V Off
12V 12V Invalid
Motor
Pin1
GND
SPEED +5V DIR
GND

Quick Start Guide www.nxp.com
8 9
PUSH BUTTONS AND SWITCHESHEADERS AND CONNECTORS
HEADER/CONNECTOR DESCRIPTION
J1 HALL sensor connector
J2
Pin 1 Motor1_Out
Pin 2 Motor0_Out
J5
Pin 1 LIN
Pin 2 GND
Pin 3 VBAT
J6 BDM Connector
J11 External temperature sensor connector
HEADER/CONNECTOR DESCRIPTION
SW1 Push button connects to a high voltage input
pin
SW3 Switch used to control motor direction
SW4 Push button reset

Quick Start Guide www.nxp.com
10 11

www.nxp.com/automcdevkits
NXP, the NXP logo and CodeWarrior are trademarks of NXP B.V. All other product or service names are
the property of their respective owners. © 2016 NXP B.V.
Document Number: S12VR32EVBQSG REV 0
SUPPORT
Visit www.nxp.com/support for a list
of phone numbers within your region.
WARRANTY
Visit www.nxp.com/warranty for
complete warranty information.
Get Started
Download installation
software and documentation under
“Jump Start Your Design” at
www.nxp.com/S12VR32EVB.