D-Link DCS 6513 User manual

This document will guide you through the basic
installation process for your D-Link Network
Camera.
DCS-6513
Quick Install Guide
Full HD WDR Day & Night Outdoor Dome Network Camera

D-Link DCS-6513 Quick Install Guide
2
DCS-6513 Quick Install Guide
The install guide provides basic instructions for installing the DCS-6513 Network Camera. For
additional information about how to use the camera, please see the User Manual which is available
on the CD included in this package or from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. microSD Card Installation
4. Hardware Installation
5. Conguration with Wizard
6. Adjusting the 3-axis gimbal
1. Package Contents
DCS-6513 Network Camera
Manual and Software on CD-ROM
Quick Install Guide
Power Adapter
Security Wrench
Extension Adapter
Cable Cover
Screws
Rubber Plug
Weather Shield
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all local
codes and prevent voiding your warranty.

D-Link DCS-6513 Quick Install Guide 3
2. Hardware Overview
Install the microSD Card
Push the microSD card* into the camera with the gold
contacts oriented towards the base of the camera. To
eject, push the microSD card into the slot.
* microSD card is sold separately
3. microSD Card Installation
Disassemble the Camera
Open the camera enclosure by loosening the
four screws. Lift the dome o the base of the
camera.
Power Connector
Connects to 12V DC power
adapter.
24V Power Connector
Connects to 24V AC power.
BNC
Analog video output.
Ethernet Jack
RJ-45 connector for Ethernet which can also be used to
power the camera using Power over Ethernet (PoE).
Reset Button
Resets the camera to its
factory default settings.
Audio In
Connects to a microphone.
DI/DO Wiring, 12V DC Output
I/O connectors for external devices
Audio Out
Connects to external speakers.

D-Link DCS-6513 Quick Install Guide
4
4. Standard Mounting Instructions
Mounting Installation
Refer to the User Manual for detailed instructions regarding installation and mounting of the
camera using a mounting bracket.
Style 1 - Concealed Cable Installation
Height: 23mm (0.9 inches)
Diameter: 183mm (7.2 inches)
Weight: 400g (0.9lbs)
Figure 2.1
Figure 2.2
Weather Shield
Weather shield
37mm screw

D-Link DCS-6513 Quick Install Guide 5
Style 2 - Exposed Cable Installation
Height: 23mm (0.9 inches)
Diameter: 183mm (7.2 inches)
Weight: 400g (0.9 lbs)
Figure 2.3 Figure 2.4
Figure 2.6
Figure 2.5

D-Link DCS-6513 Quick Install Guide
6
Pendant Mount (DCS-34-2)
Height: 201mm (7.9 inches)
Diameter: 150mm (5.9 inches)
Weight: 665g (1.45lbs)
Figure 3.4
Pendant
Bracket
Bracket Cap
Rubber
Seal
Figure 3.2
Figure 3.3
Figure 3.1
Bracket
Cap
Mounting
Plate

D-Link DCS-6513 Quick Install Guide 7
Wall Mount (DCS-34-3)
Height: 253mm (9.96 inches)
Diameter: 150mm (5.9 inches)
Weight: 770g (1.7lbs)
Bracket Cap
Bent
Bracket
Figure 4.2
Figure 4.4
Figure 4.3
Figure 4.1
Bracket
Cap
Mounting
Plate
Dome
Camera
Bent
Bracket

D-Link DCS-6513 Quick Install Guide
8
Connection with a PoE Switch
If you are using a PoE switch, connect the IP camera to the switch via an Ethernet cable, which will
provide transmission of both power and data over a single cable.
General Connection Using 24V AC Power Wiring
1. Connect the network camera to a switch or router via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power source such as your building's
emergency power.
General Connection Using 12V DC Power Adapter
1. Connect the network camera to a switch or router via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.

D-Link DCS-6513 Quick Install Guide 9
5. Conguration with Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-6513 CD into your computer's CD-ROM drive to begin the installation. If the Autorun
function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click
Start > Run. Type D:\autorun.exe, where D: represents the drive letter of your CD-ROM drive.
After clicking Setup Wizard, the following window will open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to nish.

D-Link DCS-6513 Quick Install Guide
10
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select Static IP if the
camera will use the same IP address each time it is started.
Click Next to proceed to the next page.
Enter the Admin ID and password. When logging in for the
rst time, the default Admin ID is admin with the password
left blank.
Click Next to proceed to the next page.
The Setup Wizard will appear and display the MAC address
and IP address of your camera(s). If you have a DHCP server
on your network, a valid IP Address will be displayed. If your
network does not use a DHCP server, the network camera's
default static IP 192.168.0.20 will be displayed.
Click the Wizard button to continue.