Dacor Preference Renaissance RGC304 Technical manual

PLANNING
GUIDE
www.Dacor.com
Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. CI.11
Stiffener
Cabinet face
Countertop
Floor
5/8” Min. (16 mm) space
behind raised vent
chassis to clear stiffener
5/8” Min. (16 mm)
flat countertop overhang
required behind cutout
RV series raised vent:
Check raised vent
dimensions/specifications
to determine proper fit
SGM Series Cooktop
RGC/SGM Series Drop-In Gas Cooktop
with RV Series Raised Vent
COMBINATION INSTALLATIONS
Document # PGCI-007 Revised 05/07/09 Page 1/2
WARNING
Observe all governing codes and ordinances during◊
planning and installation. Contact your local building
department for further information.
All appliances must be installed in accordance with the◊
accompanying installation instructions.
All tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted
Countertop Dimensions
Installation Type Cutout
Diagram C (Min.) D E F G H
RGC/SGM304
with RV30
Figure 1
(Square)
5/8”
(16 mm)
22 1/4” *
(565 mm)
27 3/4”
(686 mm) NA NA NA
RGC/SGM365
with RV36
Figure 1
(Square)
5/8”
(16 mm)
22 1/4” *
(565 mm)
33 5/8”
(854 mm) NA NA NA
SGM466 with
RV46
Figure 2
(Notched)
5/8”
(16 mm)
22 1/4” *
(565 mm)
44 3/4”
(1137 mm)
43 1/2”
(1105 mm)
5/8”
(16 mm)
2 5/8” **
(67 mm)
Cutout Dimensions
Side View - RGC/SGM Series Cooktop with
RV Series Raised Vent
IMPORTANT: Be careful to use the correct cutout diagram (on page 2/2) to determine the countertop dimensions. Carefully double check
all dimensions against the table below and the correct diagram before cutting the countertop.
* Total cutout depth, accommodates both the cooktop and raised vent
** IMPORTANT: Notch depth is included in total cutout depth (D). DO NOT add notch depth to total cutout depth (D).
RGC or SGM series cooktop

PLANNING
GUIDE
www.Dacor.com
Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. CI.12
RGC/SGM Series Drop-In Gas Cooktop
with RV Series Raised Vent
COMBINATION INSTALLATIONS
All tolerances: +1/16”, -0, (+1.6mm, -0) unless otherwise stated
Document # PGCI-007 Revised 05/07/09 Page 2/2
4 1/4" (108 mm) Min.
from mounting surface to
combustibles below
cooktop chassis
E
C
D
7 1/2" (191 mm) Min.
to combustible
side wall above
countertop
(both sides)
Vertical
combustible
surface
Rear
wall
1 7/8" Min.
(48 mm)
E
C
D
H
H
G
F
7 1/2" (191 mm) Min.
to combustible
side wall above
countertop
(both sides)
Vertical
combustible
surface
Rear
wall
1 7/8" Min.
(48 mm)
4 1/4" (108 mm) Min. from
mounting surface to combustibles
below cooktop chassis
Figure 1 - Square Countertop Cutout Diagram
Figure 2 - Notched Countertop Cutout Diagram
(SGM466 only)