Daewoo DV-K224D User manual

REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Instruction manual
Video recorder
DV-K224D
GB
English
DV-K224DY-RG/H _GB(¨£` )-˙¥` 01.4.18 5:34 PM ˘ ` 1

DV-K224DY-RG/H _GB(¨£` )-˙¥` 01.4.18 5:34 PM ˘ ` 2

REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Precautions
WORTH
knowing
Please keep the video machine's guarantee card and receipt safe for warranty
purposes.
◆Read carefully through this manual to familiarize yourself with this
high-quality Daewoo video recorder.
◆Make sure the rating of your household electricity supply matches
that shown on the back of the video recorder.
◆Refer to this chapter and the "Initial installation" chapter to help
you install and adjust your video recorder.
◆The appliance is not intended for use by young children or infirm
persons without supervision.
◆Young children should be supervised to ensure that they do not play
with the appliance.
Do not ...
... expose the video recorder to high levels of humidity and heat, to
avoid the risk of fire and electric shock.
...
open the video recorder. Have a qualified technician carry out repairs.
... connect the video recorder to the power supply if you have just
moved it from a cold to warm environment. This can result in
condensation inside the recorder and cause serious damage to the
machine and cassettes. Wait around two hours to allow it to reach
room temperature.
Make sure ...
... the recorder is placed on a steady, flat surface.
... you place the recorder where there is good ventilation all around.
... you clean the recorder only with a soft, lint-free cloth; do not use
aggressive or alcohol-based cleaning agents.
... you disconnect the power supply if the recorder appears to be
working incorrectly, is making an unusual sound, has a strange
smell, has smoke emitting from it or liquids have got inside it. Have
a qualified technician check the recorder.
... you disconnect the power supply and aerial if you will not be using
the recorder for a long period or during a thunderstorm.
For your own safety!
◆There are no components in this video recorder you can
service or repair yourself.
◆Do not open the case of the video recorder. Only allow
qualified personnel to repair or service your set.
◆This video recorder is designed for continuous
operation. Switching it off does not disconnect it from
the mains (stand-by). To disconnect it from the mains,
you have to unplug it.
◆Recording any copyright protected material may infringe
a copyright.
REW FF
POWER STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
PAL
REW FF
POWER STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
PAL
AUTOSET
CH.
OP EJECT
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
PAL
REW FF
POWER STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
PAL
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` b

ENGLISH
Contents
knowing
WORTH
Before doing anything with the machine, please
read the chapter "Initial installation".
◆On the following pages, the pictures show the buttons you press on the remote control to
perform the function, and what you should see in the On Screen Display or machine
display (if present).
Controls
The remote control unit ................................................................................. 2
The machine, On screen display .................................................................... 3
Initial installation
Connecting up the video recorder, Fitting the remote control’s batteries .... 4
Setting up the video recorder ........................................................................ 5
Playing cassettes
Playing back .....................................................................................................6
Still, Variable picture search, Variable slow motion,
Accessing new recordings (index scan) ......................................................... 7
Recording cassettes
Simple recording, One touch recording (OTR) ............................................... 8
Setting time and date .................................................................................... 9
More functions
Normal timer recording ................................................................................ 10
Timer Review – changing and erasing .........................................................11
Clock/counter display, Remaining time and Cassette length,
Resetting the counter to zero, Accessing counter zero position ................ 12
Menu languages, Child lock, Cassettes, and ... .......................................... 13
Tuning in new stations
Tuning ........................................................................................................... 14
Station names .............................................................................................. 15
Sorting programme locations, Clearing programme locations ................... 16
Connections and copying
To the TV via antenna cable (if you are not using a RCA cable) ................. 17
Copying, Assembling .................................................................................... 18
Appendix
Brief instruction for experienced users .................................................. 19/20
Before you ask a specialist .......................................................................... 21
Index, Technical data ................................................................................... 22
1
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` 1

The remote control unit
CONTROLS
◆ The remote control is the principle means of control, but the main playback and
record functions are also available on the front of the machine.
◆ Press any button (except ) to turn on the power.
power off (standby)
this button is not available for this set
a button for selecting input sources for recording:
TV stations – input sockets
remain time and cassette length on-screen display
to reset the counter
to wind the cassette to counter position 0:00:00
clock / counter on-screen display
to eject the cassette
the variable slow motion button
these buttons are not available for this set
to search the beginnings of records (index)
this button is not available for this set.
the record or OTR button
(One Touch Recording means: each time you press the
button recording is extended by 30 minutes)
pause (record), still (playback)
playback start
playback stop
rewinding/fast forwarding a cassette from Stop, or
picture search backwards/forwards from playback mode
number buttons to select programmes (stations) or to type
in numbers
the menu controls, programme (station) selection (PR +/–)
2
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
max. 7 m.
30° 30°
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
T.R
AV
T.R
00:00
/
/
EJECT
SP/LP
A.SEL
INDEX
PR
MENU
OK
PR
The buttons to use
are marked on the
following pages.
/
123
456
7
0
89
AV
TV/VCR
PAL/SEC
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` 2

ENGLISH
The machine
On screen display
CONTROLS
◆ Press any button (except ) to turn on the
power.
programme (station) selection
recording or OTR
(One Touch Recording means: each time you press the button recording is extended by
30 minutes)
rewinding / fast forwarding a cassette from Stop, or picture search
backwards / forwards from playback mode.
playback start
power off (standby)
playback stop and ejecting the cassette
3
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
STANDBY
STOP/ EJECT
CHANNEL
REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
MAIN MENU
Timer Program
Timer Review
VCR Setup
PR+/-:select
OK:confirm MENU:end
VCR SETUP
PR Preset
Clock Set
Language Set
RF Output Set
PR+/-:select
OK:confirm MENU:end
example
MENU
PR
OK
The video’s menu system
gives you easy-to-
understand access to the
less used functions such
as tuning to stations, clock
setting and more.
The menus show you
which button to press
for the next step.
In addition, some other
functions appear on
screen temporarily.
REW SP EURO PR04
REW FF
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` 3

REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Connecting up the video recorder
Fitting the remote control's batteries
INSTALLATION
Initial
4
Place your video
◆ horizontally on a flat, steady base so that air can circulate around it for ventilation.
◆ away from humidity and heat, magnetic fields, such as those from loudspeakers
etc., and with no heavy objects placed on top.
Switch off all components when connecting or disconnecting cables.
◆Unplug the aerial cable from your TV and plug it into the
"ANT. IN" socket of the video.
Plug the short coaxial cable provided into the "ANT.OUT"
socket of the video and the aerial socket of the TV.
◆Plug a RCA cable into the "RCA" socket of the video and
the AV socket on the TV if available.
This connection will provide best picture and sound quality.
Ask your dealer for an appropriate cable if you do not have one.
Without RCA cable, you need to follow the steps described under
"If you are not using RCA cable" (right page and page 17).
◆Make sure the rating of the household mains supply matches the
rating shown on the back of the video.
Now plug in the mains lead. The display of the video
should now light.
Fit the batteries as shown by
the pictures in the bay.
ANT . OUT
ANT . IN
AUDIO VIDEO
OUT
IN
1.5 V (AAA)
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
AC 240 V ~,
50 Hz
◆Protect your environment by returning used batteries to your dealer. Since
batteries contain toxic substances they require special disposal methods.
◆Make sure the batteries are always of the same type and age, and remove them
from the remote control if you are not using it for a long period.
The buttons to use
are marked on the
following pages.
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` 4

ENGLISH
Setting up the video recorder
INSTALLATION
Initial
◆ You can also start "Auto Search" in the menu
"PR Preset" "Auto Search".
◆ To tune in new stations (manual tuning) and to
enter station names see page 14-16.
You should see this picture the first
time you switch on the TV and video.
Choose your language.
OK for "Auto Search!".
"AUTO SEARCH" tunes in all the stations you can receive in
your country and ...
... sorts them in an order common for your country.
Then type in the current time and date.
Should you wish the stations to have the same numbers as
those used on the TV, follow the instructions in "Sorting
programme locations" on page 16.
Else ...
exit the basic installation function and enjoy your
video recorder.
◆If you don´t see this picture, because you don´t use RCA cable, search this picture now
(CH 36) with the station tuning functions of your TV set (see its user manual).
◆In case of interference problems on CH 36, type in another
transmission channel between 22 and 69 using the number buttons.
5
/
123
456
7
0
89
Auto Search!
OK:confirm MENU:end
AUTO SEARCH
MENU:end
PR03
V-L ------------ ------------
76%
setting
Please wait...
CLOCK SET
0-9:setup(hour)
/ :correct MENU:end
Time - -: - -
Date - - / - - / - - - -
MANUAL SET
PR01 P-01 PRO6 P-06
PR02 P-02 PRO7 P-07
PR03 P-03 PRO8 P-08
PR04 P-04 PRO9 P-09
PR05 P-05 PR1O ----
PR+/-:select
OK:confirm MENU:end
AUTO SEARCH
PR
OK
OK
OK
MENU
LANGUAGE SET
English Français
Deutsch Netherlands
Italiano PYCCK
Español
PR+/-:select
OK:confirm MENU:end
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` 5

6
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Playing back
cassettes
PLAYING
◆ Your TV and your video recorder are switched on.
◆ To see the picture from your video, press the station button on the TV reserved for
video input or the AV (Audio/Video) button.
Load the cassette by pushing
it smoothly and squarely into
the cassette bay, with its
windows pointing up.
Start playback.
Stop playback.
Eject the cassette.
Fast forward or rewind the
cassette from stop.
◆When you load a protected cassette (e.g. pre-recorded film,
see page 13) playback starts automatically.
◆PLAY switches back to normal playback.
◆During still, slow or search, you don’t hear the sound.
◆If the still picture is jittering, you can steady it by using the PR +/–
buttons.
◆You can reduce horizontal interference stripes resulting from
inaccurate tracking (when playing tapes of poor quality or recorded
on other machines) by using the PR +/– buttons during playback.
◆After approx. 5 minutes in still, the cassette plays back
automatically.
◆Clock / Counter / Remaining time – page 12
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
EJECT
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
VCR
S P
VCR
S P
VCR
S P
VCR
S P
VCR
S P
AUTO SET
20 : 10
VHS
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:9 PM ˘ ` 6

ENGLISH
Still
Variable picture search
Variable slow motion
Accessing new recordings (index scan)
PLAYING
cassettes
Still picture from playback.
Each press of the button advances the picture
one frame.
PLAY switches back to normal playback.
Starting from playback you can control search
speed in 2 steps either forwards (¤¤ ) or
backwards (ˆˆ ). Press repeatedly.
PLAY switches back to normal playback.
Starting from playback you can control slow
motion speed in 6 steps (1/15, 1/10, 1/5, 1/30,
1/25, 1/20, 1/15, ...). Press repeatedly.
PLAY switches back to normal playback.
Select INDEX + or INDEX – to search forwards or
backwards.
The video will now wind to the beginning of the first
recording, play it for about 6 seconds then wind on to the
next one.
When you see the recording you want, press
PLAY.
Access the beginning of recordings in the middle of the tape using the Index + / – function.
The video recorder automatically sets an electronic marker (index) at the beginning of each
recording. It is these markers which the Index + / – function detects.
7
INDEX
VCR
S P
VCR
S P +
VCR
S P -
VCR
S P
F.FWD SP AV
INDEX SEARCH 01
0:01:47
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 7

8
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Simple recording
One touch recording – OTR
RECORDING
cassettes
◆ The TV stations on the video have been tuned in (page 5).
◆ The video is switched on.
◆ You can either watch the picture from the video on the TV by pressing the station
button reserved for video input or the AV button, watch another TV station or
switch off the TV altogether.
Load a cassette with its
safety tab in place (see page 13).
Start your recording.
If you wish to interrupt
recording briefly - then
continue.
Stop your recording.
Choose the station whose
programme you want to
record.
◆If you want to record from a source connected to your video see
page 18.
◆To cancel OTR press the button (stop) more than 5 seconds.
◆The video stops automatically, if pause exceeds five minutes.
◆Clock / Counter / Remaining time – page 12.
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
AUTOSET
20 : 10
VHS
Choose the station you want
and press the button once for
every 30 minutes of
programme you wish to
record.
Up to ten hours are possible.
PR
PR
S P
VCR
S P REC
VCR
S P REC
VCR
S P
VCR
S P
TIMER
REC
STOP SP EURO PR09
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 8

ENGLISH
ENGLISH
Setting time and date
cassettes
RECORDING
9
Call the video’s "MAIN MENU",
choose "VCR Setup", then "Clock Set".
Move to the position you want to change and
type in the new values.
Wait a few seconds after typing an one-digit number.
Store and exit.
CLOCK SET
0 - 9 :setup(hour)
/ :correct
OK :confirm MENU:end
Time 16:05
Date 20/09/1998(SUN)
CLOCK SET
Time 16:05
Date 20/09/1998(SUN)
MENU
PR
OK
PR
OK
/
123
456
7
0
89
OK
MENU
0 - 9 :setup(minute)
/ :correct
OK :confirm MENU:end
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 9

10
Normal timer recording
functions
MORE
◆ For timer recordings, clock, date, and stations must be set correctly.
◆ Load a cassette with its safety tab in place
(see page 13) and with sufficient free space for the recording.
Call the video’s "MAIN MENU",
choose "Timer Program".
Decide if you want to record
"One Time", "Daily" or "Weekly"
... and confirm.
If you wish to make changes:
Move to the position you want to
change using the / buttons.
Change the setting using the PR+/- or
number buttons.
If all setting are ok, press or , till
you see “OK : confirm” in the bottom
line.
Confirm.
Switch your video off.
Type in one after the other:
◆the programme location
number,
◆the time the broadcast starts,
◆the time the broadcast ends,
◆the day of the broadcast, if it
is not today.
◆Wait a few seconds after typing an one-digit-number.
◆If you have made a mistake, move to the position you want to change
using the / buttons and change the setting.
◆If programme timings overlap, the machine will give an warning
message. If you don’t adjust the times, the machine will record the first
programme completely then continue with the second one.
◆The recorder will eject cassettes which have the safety tab removed
(page13).
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
MENU
OK
OK
OK
/
123
456
7
0
89
PR
PR
How often do you want
to record this program?
One Time
Daily(MON-FRI)
Weekly(Once a Week)
PR+/-:select
OK:confirm MENU:end
TIMERPROGRAM (OneTime)
PR+/-:select(AV)
0-9 :setup(PR)
/ :correct MENU:end
PR --
Start Time --:--
End Time --:--
Start Date --/--
TIMER PROGRAM (One Time)
PR 03
Start Time 21:20
End Time 22:20
Start Date 20/09(SUN)
/ :correct
OK:confirm MENU:end
TIMER
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
AUTOSET
20 : 10
VHS
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 10

ENGLISH
ENGLISH
Timer Review – changing and erasing
functions
MORE
Call the video’s "MAIN MENU",
choose "Timer Review".
Select the programming to change or erase.
If you want to erase this programming press
button 0, confirm with OK.
If you wish to make changes:
Move to the position you want to change using
the
/ buttons.
Change the settings using the PR +/– or number
buttons.
If all setting are ok, press or , till you see
"OK: confirm" in the bottom line.
Confirm changes with OK. Exit the menus.
11
MENU
OK
PR
OK
MENU
PR
PR
TIMER REVIEW
PR START END DATE
01 12:30 15:15 22/09
03 21:20 22:20 20/09
PR+/-:select
OK:confirm MENU:end
TIMER REVIEW
PR START END DATE
01 12:30 15:15 22/09
03 21:20 22:20 20/09
PR+/-:select
OK:confirm MENU:end
TIMER PROGRAM (One Time)
PR 03
Start Time 21:20
End Time 22:20
Start Date 20/09(SUN)
0 :erase
/ :correct MENU:end
PR
MENU
OK
PR
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 11

12
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Clock / counter display
Remaining time and cassette length
Resetting the counter to zero
Accessing counter zero position
MORE
functions
◆ The counter counts in real time from the point you load the cassette. This does not
have to be its beginning! The counter does not count unrecorded parts of the tape.
◆ If you rewind beyond the zero position, the counter counts in negative values
(e.g. – 0:01:15).
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
STOP SP AV
14:00 03/07
0:00:04
1x: Time and date (shortly),
2x: Counter (shortly),
3x: The counter stays
4x: The counter disappears
Counter display is only possible
when a cassette is loaded.
Reset the counter.
The video will wind to the
position 0:00:00 and stop.
When you want the video to
show the time remaining from
the current video tape position
(to find out if there is sufficient
space for a recording, for
example).
To ensure the remaining time shown is accurate, select the
length of cassette currently loaded by pressing this button
several times until you reach the correct length.
After the cassette length display has disappeared, pressing the button
once more causes the remaining time display to disappear.
Remaining time display is only possible when the cassette is loaded.
/
T.R
00:00
/
STOP SP AV
0:00:00
REW SP AV
GO TO ZERO
0:03:39
E-240 1:27
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 12

ENGLISH
ENGLISH
MORE
functions
13
Menu languages
Child lock
and ...
Cassettes
Call the video’s "MAIN MENU", choose
"VCR Setup", then "Language Set".
Select your language.
Confirm.
Press the button for about 5 seconds.
Your video can´t be operated now, only timer recordings will
be performed. Keep your remote control in a safe place.
To release child lock, press the button again for 5 seconds.
Dimmer
Your video recorder dimms its display when switched to stand-by mode.
Auto power off
Your video recorder switches to stand-by when no tape is played and no
station is received for more than 5 minutes.
Use only good quality tape cassettes with the VHS logo.
◆Keep cassettes away from excessive moisture or dust, magnetic and
electrical fields (loudspeakers and computer monitors, for example).
◆Always wind the tape to the beginning when you have finished. Store
with the full spool at the bottom and with the cassette in its cover.
You can protect your precious recordings from being wiped by breaking out
the safety tab on the side of the cassette (some cassettes have a slide).
Should you wish to re-use the tape after removing the tab, cover the hole
with adhesive tape.
PR
OK
PR
LANGUAGE SET
PR+/-:select
OK:confirm MENU:end
PAL
MENU
English Français
Deutsch Netherlands
Italiano PYCCK
Español
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 13

14
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Tuning
NEW STATIONS
T u n i n g i n
◆ The TV and video recorder are switched on.
◆ To see the picture from your video, press the station button on the TV reserved for
video input or the AV (Audio / Video) button.
◆ "AV" should not be selected with the AV button .
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
Call the video’s "MAIN MENU",
choose "VCR Setup",
then "PR Preset".
Select "Manual Set".
Choose any unused location
number "----" or "P-xx" ...
It's simplest to use the same location
number on both the TV and video.
... and confirm.
Tune in the station you want.
Press button to see the
picture.
If it isn’t the station you want, or the
picture is disturbed, carry on tuning.
Once you see the station you
want, store it.
See facing page for station names.
Tune in further stations (from
step 3 onwards) or exit tuning
mode.
MENU
PR PRESET
Auto Search
Manual Set
PR Erase
PR Align
PR+/-:select
OK:confirm MENU:end
MANUAL SET
PR01 P-01 PRO6 P-06
PR02 P-02 PRO7 P-07
PR03 P-03 PRO8 P-08
PR04 P-04 PRO9 P-09
PR05 P-05 PR1O ----
PR+/-:select
OK:confirm MENU:end
MANUAL SET
PR+/-:search up/down
MENU :end
PR10
V-L ----------- --------------
68%
MANUAL SET
PR+/-:search up/down
:station correct
:PR view
OK:confirm MENU:end
PR10
Station Name
P-10
MANUAL SET
PR+/-:search up/down
:station correct
:PR view
OK:confirm MENU:end
PR10
Station Name
----
2x
PR
OK
PR
OK
PR
PR
OK
PR
PR
OK
MENU
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 14

ENGLISH
Station names
NEW STATIONS
T u n i n g i n
15
◆The video's automatic tuning system usually produces the best results. In poor reception areas,
fine tuning may improve reception. Choose the station and tune using the / buttons.
Store, typing in the location number again.
◆Should you wish to tune in all the channels available in your region, please refer to page 5.
◆Should you wish to sort or clear stations, please refer to page 16.
If your video is showing no station name or is showing a station name incorrectly, you can
correct this. Select the station.
Call this menu (just see the left page),
if it isn't displayed.
PR
Select "station correct".
Either select the name from the stored list ...
MANUAL SET
PR+/-:station change
:station correct
OK:confirm MENU:end
PR10
Station Name
EURO
... or you select "station correct" again and enter
the 4-digits name.
Change the letters with the PR +/– buttons,
move to the next letter with the
/ buttons.
PR
OK
PR
MANUAL SET
PR+/-:select character
/ :select position
OK:confirm MENU:end
PR10
Station Name
E - - -
Store and exit.
MENU
OK
MANUAL SET
PR01 P-01 PRO6 P-06
PR02 P-02 PRO7 P-07
PR03 P-03 PRO8 P-08
PR04 P-04 PRO9 P-09
PR05 P-05 PR1O EURO
PR+/-:select
OK:confirm MENU:end
MANUAL SET
PR+/-:search up/down
:station correct
:PR view
OK:confirm MENU:end
PR10
Station Name
----
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 15

16
REW FF
STANDBY STOP/ EJECT
CHANNEL REC/OTR
R
A
P
I
D
R
E
W
I
N
D
S
Y
S
T
E
M
P
L
A
Y
Q
U
I
C
K
S
T
A
R
T
M
E
C
H
A
N
I
S
M
Sorting programme locations
Clearing programme locations
NEW STATIONS
T u n i n g i n
INDEX
/
/
00:00
123
456
7
0
89
PAL/SEC
T.R
AV
SP/LP
A.SEL
EJECT
TV/VCR
PR
MENU
OK
PR
If the location numbers used for programmes stored in your TV and
video are different, you can change them on the video.
To do this, move the stations to the right numbers, until they are
arranged the way you want.
MENU
OK
OK
OK
PR
PR
PR
PR
PR ERASE
PR+/-:select
:PR view
OK:erase MENU:end
Call the video’s "MAIN MENU",
choose "VCR Setup", then "PR
Preset" then "PR Align".
Call the video’s "MAIN MENU",
choose "VCR Setup", then "PR
Preset" then "PR Erase".
Select the programme to swap.
Confirm.
Move the station to the desired
location number.
Confirm.
Select the station (location
number) you want to clear.
Review the picture.
Clear.
2x
2x
MENU
2x
PR ALIGN
PR01 P-01 PRO6 P-06
PR02 P-02 PRO7 P-07
PR03 P-03 PRO8 P-08
PR04 P-04 PRO9 P-09
PR05 P-05 PR1O ----
PR+/-:select
:PR view
OK:confirm MENU:end
PR01 P-01 PRO6 P-06
PR02 P-02 PRO7 P-07
PR03 P-03 PRO8 P-08
PR04 P-04 PRO9 P-09
PR05 P-05 PR1O ----
PR
OK
PR
OK
PR
OK
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 16

ENGLISH
ENGLISH
To the TV via antenna cable (if you are not using a RCA cable)
a n d c o p y i n g
CONNECTIONS
◆ If you are using a RCA cable, select the AV
input on the TV to see the picture from the
video.
◆ If you are not using a RCA cable, select the
button number on the TV reserved for video
input to see the picture from the video.
17
If you are not using a RCA cable, your video can transmit pictures and sound to the TV via the
coax aerial cable. Just tune the TV to the video's transmitting channel (factory set to UHF CH
36). Tune the TV carefully to ensure the best pictures and sound.
Once you have carried out the steps in
"Connecting up the video recorder" (page 4),
switch on your TV.
Press the OK button of the video’s remote control
longer than 3 seconds to call the video´s test
picture.
Tune the TV to the test picture using the channel
pre-set functions of your TV as described in its
manual.
When you have found the test picture, store it
under the button number on your TV for video
input.
Press the OK button of the video`s remote control
again longer than 3 seconds to release the test
picture.
Call the video’s "MAIN MENU" choose
"VCR Setup" then "RF Output Set".
Type in the free channel.
Store and exit.
If the quality of the test picture transmitted to the TV is poor due to interference caused by
a station transmitting on channel 36, you can tune the video to a different transmitting
channel. Find a free channel between 22 and 69 on your TV.
◆If the quality of the test picture transmitted to the TV is poor, fine-tuning on the TV may
help (refer to the TV manual).
RF OUTPUT SET
0-9:setup(22-69)
OK:confirm MENU:end
/
123
456
7
0
89
3 sec.
OK
MENU
PR
OK
PR
OK
OK
MENU
PR 36
DV-K224DY-RG/H_GB(¨£` )-‡»¿º 01.4.18 6:10 PM ˘ ` 17