Dahua VTO2000A Series User manual

IP Villa System
Quick Start Guide
Version 1.0.0

1
Welcome
Thank you for purchasing our device!
This quick start guide will help you become familiar with our device in a very short time.
Before installation and operation, please read the following safeguard and warning carefully!
Important Safeguard and Warning
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The product must be grounded to reduce the risk of electric shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Keep upwards. Handle with care.
Do not apply power to the device before completing installation.
Do not place objects on the device.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
The device should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included:
Contact your local retailer ASAP if something is missing in your package.
CAUTION
FOR YOUR OWN SAFETY, PLEASE CHANGE SYSTEM DEFAULT PASSWORD
AFTER YOU FIRST LOGIN!

2
Table of Contents
1Typical Connection ..............................................................................................3
2General Settings...................................................................................................4
2.1 Change Default Password........................................................................4
2.2 VTO Settings ..............................................................................................4
2.3 Master Digital VTH Settings.....................................................................6
2.4 Digital Extension VTH Settings................................................................8
2.5 Change Villa VTO IP via VTH..................................................................9
2.6 Check Results ..........................................................................................12
3Network Camera Settings.................................................................................13
3.1 VTH Settings ............................................................................................13
3.2 Add Dahua Network Camera.................................................................13
3.3 Add ONVIF Network Camera ................................................................13
3.4 Check Results ..........................................................................................14
3.5 VTO Settings ............................................................................................14
3.5.1 Add Dahua Network Camera ......................................................14
3.5.2 Check Results................................................................................14
4Cell Phone Settings ...........................................................................................15
4.1 VTO Settings ............................................................................................15
4.2 Cell Phone Settings.................................................................................15
4.3 Check Results ..........................................................................................17
5Installation ...........................................................................................................18
5.1 VTO Installation........................................................................................18
5.1.1 Direct Installation...........................................................................18
5.1.2 Embedded in Wall.........................................................................19
5.2 VTH Installation........................................................................................21
5.2.1 Installation Mode 1........................................................................21
5.2.2 Installation Mode 2........................................................................21
6Electric Lock and Magnetic Door Lock ...........................................................22
6.1 Electric Door Lock....................................................................................22
6.2 Magnetic Door Lock ................................................................................22
7Appendix Specifications ....................................................................................23

3
1Typical Connection
Note: All the installation and operations here should conform to your local
electric safety rules.
When a visitor press call button on VTO, multiple VTHs will ring at the same time. You can call,
hang up, and unlock on any of these VTHs.
1.1 IP Connection Mode 1
This mode is for VTO2000A/VTH1550CH/VTH1560B.
VTH has one master VTH and up to three extension VTHs. See Figure 1-1.
Figure 1-1
1.2 IP Connection Mode 2
This mode is for VTO2000A-2/VTH1550CHW-2.
The VTH has two types: one master VTH and up to three extension VTHs. See Figure 1-2.
Figure 1-2

4
2General Settings
The VTO default IP address is 192.168.1.110. The default WEB account is: user name: admin,
password: admin.
The VTH default IP address is 192.168.1.109, the project password is 002236.
After the connection, please make sure the VTH and VTO connection are OK. Please change
the default password after your first login.
2.1 Change Default Password
Please refer to Figure 2-1 to change VTO password.
Figure 2-1
Please refer to Figure 2-2 to change account password, open door password, arm/disarm
password, an-hijack password of the VTO (Settings->Password).
Figure 2-2
2.2 VTO Settings
a) Please use the PC to access the VTO. Open the browser and then input the VTO IP address.
Click the Enter, input user name and password to login. System supports English, Russian,
Italian, French, Germany, Dutch, Spanish, and Portuguese by default. See Figure 2-3.

5
Figure 2-3
b) Now you can set local information. See Figure 2-4.
Figure 2-4
c) Now you can add digital VTH. System has added room 9901 by default. See Figure 2-5.
Figure 2-5

6
d) Set network information. See Figure 2-6.
Figure 2-6
2.3 Master Digital VTH Settings
a) When device is booting up, you can set device language. System supports English, Russian,
Italian、French, Germany, Dutch, Spanish, and Portuguese by default. See Figure 2-7. After
device booted up, you can go to Settings->Language->002236 to change language
again.
Figure 2-7
b) On the main VTH menu, from System->Project, you can input project password 002236 to
go to the project setup interface.

7
c) Set current VTH as the master VTH. See Figure 2-8.
Figure 2-8
d) Click Network on the right pane, and then input master VTO name, IP address and enable
current function.
Note: Click to go to the extension VTO interface; you can set extension VTO
information. You can several extension VTOs at the same time. See Figure 2-9.
Figure 2-9

8
2.4 Digital Extension VTH Settings
a) On the extension VTH menu, from System->Project, you can input project password
(002236) to go to the project interface.
b) Set current VTH as extension VTH.
Step1 Press Product Info, See Figure 2-10
Step2 Press Master, Master icon becomes Extention icon.
Step3 Set Room No. (i.e. 9901-1), input IP Address, Subnet Mask and Gateway.
Step4 In Master IP, input IP of the master VTH.
Figure 2-10
c) Click Network on the right pane and then enable current function. See Figure 2-11.
Figure 2-11
d) Click to go to the next page to set extension VTO. Enable current function and then click
OK.

9
Note
Please make sure the status is ON. The extension VTH can synchronize information with the
master VTH. If one master VTH has several extension VTOs, please enable status as on.
See Figure 2-12.
Figure 2-12
2.5 Change Villa VTO IP via VTH
a) On the digital VTH interface, from Settings->Project->002236, select Search device. See
Figure 2-13.
Figure 2-13

10
b) Change VTO IP address as 192.168.1.11. See Figure 2-14.
Figure 2-14
c) Click Add to add VTO settings. See Figure 2-15.
Figure 2-15

11
d) Use 192.168.1.11 of the VTO to change default setup 192.168.1.110, change status as
on. See Figure 2-16.
Figure 2-16
e) Now you can see the following interface. See Figure 2-17.
Figure 2-17

12
f) Or you can go to the Network interface to view the add result. See Figure 2-18.
Figure 2-18
2.6 Check Results
On the indoor VTO, click monitor button, you can view the situation of the VTO.
On the villa VTO, click the Call button, you can call any of the VTHs.
For the VTH, from “Video Talk->Call User”, input “-1”to call the VTH extension number.
See Figure 2-19.
Figure 2-19

13
3Network Camera Settings
3.1 VTH Settings
The VTH supports 8 network cameras. It supports product from Dahua and ONVIF protocol.
3.2 Add Dahua Network Camera
On the VTH menu, from Settings-> Local IPC, input network camera name, IP address, port
(5000), protocol (local) and then click Save button. User name and password are the account for
you to login the network camera. See Figure 3-1.
Figure 3-1
3.3 Add ONVIF Network Camera
On the VTH menu, from Settings-> Local IPC, input network camera name, IP address, port (80),
protocol (ONVIF) and then click Save button. User name and password are the account for you
to login the network camera. See Figure 3-2.
Figure 3-2

14
3.4 Check Results
On the VTH menu, from Video Talk-> Monitor->IPC, you can use Last Channel/Next Channel to
switch to different network camera video. See Figure 3-3.
Figure 3-3
3.5 VTO Settings
For the VTO, it supports 24 network cameras. It supports product from Dahua.
3.5.1 Add Dahua Network Camera
Please refer to the following interface. See Figure 3-4.
Figure 3-4
3.5.2 Check Results
Please refer to chapter 3.4.

15
4Cell Phone Settings
4.1 VTO Settings
a) Go to the Network interface, set VTO IP address so that it can connect to the network. Set
local DNS address. See Figure 4-1.
Figure 4-1
b) Go to P2P interface; check the box to enable the P2P function. Please wait until the status
becomes on. See Figure 4-2.
Figure 4-2
4.2 Cell Phone Settings
a) Scan the QR code to download the APP. See Figure 4-3.
APP for iPhone OS APP for Android OS
Figure 4-3

16
b) Use the cell phone to scan the QR code of VTO on the device’s label or Web. See Figure
4-4 and Figure 4-5.
Figure 4-4
Figure 4-5

17
c) Give a name to VTO first. Click the detect VTO. You can view the corresponding video from
the VTO after it detects the device.
Figure 4-6
4.3 Check Results
When the VTO is calling the VTH, you can see a push message on your cell phone. Open the
message; you can see the video from the VTO.
Figure 4-7

18
5Installation
5.1 VTO Installation
This VTO2000A series product supports direction installation and embedded in wall installation.
5.1.1 Direct Installation
a) Install metal bracket into the groove on wall. Secure 4 fasten screw (ST4.2×25), and fix
metal bracket on wall. See Figure 5- .
Component Name
Icon
No.
ST4.2×25 Cross recessed pan head tail
tapping screws -stainless
4
FEC5-30 plastic expansion bolt
4
Figure 5- 1
Figure 5-2
b) Align the device on metal bracket according to screw hole. Fasten screw (M3×8 Cross
recessed countersunk head tail machine screws --- galvanizing white), and fix device on
metal bracket. See Figure 5- 1.
Component Name
Icon
No.
M3×8 Cross recessed countersunk head tail
machine screws --- galvanizing white
4
M3×6 Hex slot pan head tail machine
screws --- galvanizing white
4
Tips:
M3x6 or M3x8 either is OK.