Daikin BRC1H61W System manual

Wired Remote
Controller
Installation Handbook
• Be sure to read before conducting the installation
of this product, and conduct installation according
to this manual.
• Refer to this manual together with the installation
manual of the indoor unit.
• It is possible to perform settings of some functions
from a smart phone app.
• For details, refer to the BRC1H61W/BRC1H61K
manual on our company website.
MODEL BRC1H61W/BRC1H61K
+
-
00_CV_3P607378-2B_IM-K.indd 1 2020/07/28 11:38:26

1
Contents
Safety Precautions ............................................................. 2
Accessories ........................................................................ 3
Button Locations and Descriptions..................................... 4
Remote controller installation procedure............................ 6
Field Setting ..................................................................... 17
License ............................................................................. 20
Certication ...................................................................... 21
01_EN_3P607378-2B_IM-K.indd 1 2020/07/28 11:39:49

2
Safety Precautions
 Also refer to installation manual attached to the indoor unit.
Please read these “Safety Precautions” carefully before installing the remote controller.
• This manual classies the precautions into WARNINGS and CAUTIONS.
Be sure to follow all the precautions below: They are all important for ensuring safety.
WARNING Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
• After completing installation, conduct a test operation to check for faults and explain to the customer
how to operate the remote controller and cleaning of it with the aid of the operation manual. Ask the
customer to store the installation manual along with the operation manual for future reference.
WARNING
Ask your dealer or qualied personnel to carry out installation work.
Do not attempt to install the remote controller yourself.
Improper installation may result in electric shocks or a re.
Consult your local dealer regarding relocation and reinstallation of the remote controller.
Improper installation may result in electric shocks or a re.
Install the remote controller in accordance with the instructions in this installation manual.
Improper installation may result in electric shocks or a re.
Be sure to use only the specied accessories and parts for installation work.
Failure to use the specied parts may result in the remote controller falling down, electric shocks or a
re.
Install the remote controller on a foundation that can withstand its mass.
Insufcient strength may result in the remote controller falling down and causing injury.
Make certain that all electrical work is carried out by qualied personnel according to the applicable
legislation (note 1) and this installation manual, using a separate circuit.
In addition, even if the wiring is short, make sure to use a wiring that has sufcient length and never
connect additional wiring to make the length sufcient.
Insufcient capacity of the power supply circuit or improper electrical construction may lead to
electric shocks or a re.
(note 1) applicable legislation means “All international, national and local directives, laws, regulations
and/or codes which are relevant and applicable for a certain product or domain”.
Turn off the power before performing installation work.
Touching live parts may cause electric shocks.
Do not disassembly, reconstruct or repair.
Failure to do so many cause electric shock or a re.
Make sure that all wiring is secured, using the specied wirings and ensuring that external forces do
not act on the terminal connections or wirings.
Improper connections or xing may cause an overheat or a re.
The choice of materials and installations must comply with the applicable national and international
standards.
01_EN_3P607378-2B_IM-K.indd 2 2020/07/28 11:39:49

3
CAUTION
To avoid electric shocks due to entry of water or insects, ll the wiring through hole with putty.
Do not operate with wet hands to avoid electric shocks.
Do not wash the remote controller with water.
Failure to do so many cause electric shock or a re.
Install the air conditioner, power supply wiring, remote controller wiring and transmission wiring at
least 1 meter away from televisions or radios to prevent image interference or noise.
(Depending on the radio waves, a distance of 1meter may not be sufcient to eliminate the noise.)
Do not install the remote controller in the following locations:
1. Where there is oil mist, oil spray or vapour for example a kitchen.
Resin parts may deteriorate and fall off.
2. Where corrosive gas, such as sulphurous acid gas, is produced.
3. Where there is machinery which emits electromagnetic waves.
Electromagnetic waves may disturb the control system, and cause a malfunction of the
equipment.
4. Where ammable gas may leak, where there is carbon bre or ignitable dust suspensions in
the air, or where volatile ammables such as thinner or gasoline are handled.
Operating the unit in such conditions may result in a re.
5. High temperature area or near a heat source.
It may cause an overheat or a re.
6. Moist area, or place where may be exposed to water.
If water enters inside of the remote controller, electrical components may fail.
It may result in electric shocks or a re.
When remote controller’s thermostat sensor is used, select the installation location by considering
the followings.
• A place where average temperature in the room can be detected.
• A place where is not exposed to direct sunlight.
• A place where is far apart from heat source.
• A place where is not affected by outdoor air due to door opening/closing or the like.
Accessories
The following accessories are included.
Cross recessed round
head wood screw Drywall anchor Operation Handbook Installation Handbook
(2 pcs.) (2 pcs.) (1 pc.) (1 pc.)
01_EN_3P607378-2B_IM-K.indd 3 2020/07/28 11:39:49

4
Button Locations and Descriptions
a
b
c
d
e
f
+
-
Functions items (i.e., Operation Mode, Fan Speed, and Setpoint) are set from the menu
screen.
NOTICE
• Do not install the remote controller in places exposed to direct sunlight. The LCD may be
damaged.
• Do not pull or twist the remote controller cord. The remote controller may be damaged.
• Do not use objects with sharp ends to press the buttons on the remote controller. Damage may
result.
a ON/OFF button
• Press this button to turn on the system.
• Press this button again to turn o the system.
b Status indicator (LED)
• During operation, the light ring around the display lights up blue/red/green.
Lights up blue: Operating, Blinks red: Error is occurring, Lights up/blinks green: Bluetooth connecting
c LCD (Refer to INFORMATION on page 5.)
• Displays the current setpoint and air conditioner operation status.
d NAVIGATE/ADJUST button
• Navigate right.
• Adjust a setting.
e SELECT/ACTIVATE/SET button
• From the home screen, enter the main menu.
• From the main menu, enter one of the submenus.
• From their respective submenu, activate an operation/ventilation mode.
f NAVIGATE/ADJUST button
• Navigate left.
• Adjust the setting.
01_EN_3P607378-2B_IM-K.indd 4 2020/07/28 11:39:50

5
Home screen
30 ˚C
28
OFF
b
a
h
g
f
j
k
i
c
d
e
l
Information screen
12:34
A3-01 (Unit 00)
q
n
p
o
m
User menu/Administrator menu/Installer menu
r
User menu
r
Administrator menu/Installer menu
* The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and use of such marks by
Daikin industries, LTD. is under license. Other trademarks and
trade names are those of their respective owners.
Screen display explanation
a OFF
• Displayed when operation is stopped.
b Error/Filter/Test icon
• Error, lter and test icons are displayed.
c Centralized Control
• Displayed when under centralized management.
d Operation mode
• Displays the current operation mode.
e Ventilation mode
f Room temperature
• Displays the current room temperature.
g Setback
• Blinks during setback operation.
• Displayed during setback setting.
h Bluetooth*
• Indicates that the controller is
communicating with a mobile
device, for use with the app.
i Changeover Under Control
• Displayed when controller is unauthorized
to select heating/cooling operation.
j Fahrenheit/Celsius
• Depending on the setting, Fahrenheit/
Celsius display can be selected.
k Air Purifying
l Set temperature
• Displays setpoint temperature.
m Clock (24 hours time display)
n
MAIN/SUB remote controller sign
• : Main controller
: Sub controller
o Status
• Noties the status.
p Error display
• If an error occurs, the icon, an error
code and unit number are displayed.
q Information icon
r Settings menu icon
INFORMATION
Depending on the connected model, some items may not be displayed.
The controller is equipped with a power-saving function that darkens the display if there is no operation for a certain period of
time. To make the screen light up again, press one of the buttons.
Note that pressing one of the buttons will only make the display bright again, not cause remote controller operation.
01_EN_3P607378-2B_IM-K.indd 5 2020/07/28 11:39:51

6
Remote controller installation
procedure
Deciding where to install the remote controller
Select the installation location based on “Safety Precautions” (see page 2) and obtain
consent of the customer.
Creating a wiring through-hole in the wall (when opening a
hole in the wall and installing)
If the hole size is too large or not in the
proper location, it may be seen after the
remote controller is installed.
NOTE
3-11/64 (80.5)
13/64
(5)
33/64 (13)
1-47/64 (44)
9/32 (7)
R3/32(2.5)
R3/32(2.5)
13/64
(5)
41/64
(16.25)
1-47/64 (44)
35/64
(13.75)
3-11/64 (80.5) Back plate
Through-hole
Align the centre of the wall
hole with the centre of the
access hole on the controller
back plate when planning the
installation.
Access hole
[Unit : inch (mm)]
Back plate
Through-hole
Access
hole
CAUTION
• Note that if the wiring through-hole is large or deviates from the specied position, the hole may be
exposed.
01_EN_3P607378-2B_IM-K.indd 6 2020/07/28 11:39:51

7
Determining the wire routing direction for the back plate
Before mounting the controller, determine the wiring direction and remove a piece of the
controller’s back plate accordingly (i.e.: a, b, c). The wiring can be routed from the top, the
left, or the bottom of the back cover. Remove a piece of the back plate according to the
following gure.
After removing a thin piece with a tool such as clippers, remove burrs using a le, etc.
a Wiring from top
b Wiring from left
c Wiring from bottom
a
b
c
CAUTION
In case you are routing the wiring from the rear, you don’t have to remove anything.
When routing the wiring from the top, rear, left, or bottom, be sure to route the wiring to the upper
casing before securing the back plate.
01_EN_3P607378-2B_IM-K.indd 7 2020/07/28 11:39:51

8
Securing the back plate
Wall installation
1 : Take the cross recessed round head wood screws and drywall anchors out of the
accessory bag.
2 : Mount the back plate to a at surface.
Cross recessed round
head wood screws
Drywall anchors
CAUTION
• Install the controller on a at surface only.
• To prevent deformation of the back plate, avoid over-tightening the installation screws.
• If tightened too much, the back plate will be deformed and the upper casing will come o easily.
If the upper casing comes o easily, loosen the screws and correct the deformation.
01_EN_3P607378-2B_IM-K.indd 8 2020/07/28 11:39:52

9
Connecting the electrical wiring
All wiring must comply with the following requirements:
Wire specification Value
Wiring type Non-shielded, 2-conductor, Stranded copper wire
Wiring size AWG-18
Wiring length Maximum 1640 feet (500 m)
Prepare the wiring for connection to the remote controller following these instructions:
Approx. 3/8 inch (10 mm)
Remove the wire jacket
and insulation
To simplify the wiring, maintain
a 3/8 inch (10 mm) dierence
between the length of the two
conductors.
Cutting guideline
L
Wiring outlet L
Top ±5.5 inch (140 mm)
Left ±4.3 inch (110 mm)
Bottom ±3.5 inch (90 mm)
Rear No requirements
Connect the terminals (P1, P2) of the remote controller to the terminals (P1, P2) of the
indoor unit. (P1 and P2 are not polarity sensitive.)
CAUTION
• Before working, shut o all power supplies.
• A mounting plate for installing the remote controller and remote controller wiring are not included.
• Do not touch the remote controller circuit board directly with your hands.
01_EN_3P607378-2B_IM-K.indd 9 2020/07/28 11:39:52

10
Top outlet
P1P2
P1P2 terminal
Rear outlet
P1P2
Left outlet
P1P2
01_EN_3P607378-2B_IM-K.indd 10 2020/07/28 11:39:52

11
Bottom outlet
P1P2
CAUTION
• Keep the wiring away from the power wire so that electrical noise (external noise) is not received.
• In order to prevent the entry of water or insects, use putty (eld supply) to securely seal the wiring
lead-in hole.
Closing the controller
1 : Place the top of the controller on the
top of the back plate.
2 : Snap the bottom of the controller into
place on the bottom of the back plate.
3 : Ensure the installation site is dust-free,
before peeling the protective seal.
1
2
CAUTION
• Never touch the internal parts of the controller.
• When closing the controller, be careful not to pinch the wiring.
• To prevent damage, make sure the front of the controller is clicked into the back plate securely.
01_EN_3P607378-2B_IM-K.indd 11 2020/07/28 11:39:53

12
When removing the upper casing
Insert a at head screwdriver into the recess in the
back plate and remove the upper casing.
(2 locations)
CAUTION
• The remote controller circuit board is attached to the upper casing. Be careful not to damage the
circuit board and casing when removing the upper casing.
• Do not touch the remote controller circuit board directly with your hands.
• Be careful not to allow dust or moisture to adhere to the circuit board when the upper casing is
removed.
01_EN_3P607378-2B_IM-K.indd 12 2020/07/28 11:39:53

13
Designating a controller as main or sub
Prerequisite: A remote controller is already connected to the indoor unit.
Connect a second controller.
After turning on the power, perform setting of the second controller.
Result: It will start up automatically.
Home screen
U5
1
Wait for a U5, U8 error code to appear on the screen.
Screen display explanation
1main
2sub
Home screen
2
When the U5 error code appears, press and hold until
“2” appears on the screen.
When the U8 error code appears, press and hold until
“1” appears on the screen.
Result:
A controller displaying 1 is set as main, and a controller
displaying 2 is set as sub.
INFORMATION
If sub remote controller is not set at power-on in the case of one indoor unit controlled by two remote
controllers, Error Code: U5 is displayed in the connection checking screen.
If the sub remote controller does not display the home screen two minutes after its designation, turn
o the power and check the wiring.
01_EN_3P607378-2B_IM-K.indd 13 2020/07/28 11:39:54

14
Releasing the changeover master (VRV only)
To change the authority to choose cooling/heating, you must rst specify the remote
controller with the authority, then release the authority.
Depending on the system, setting may not be available.
Prerequisite: You are in the installer menu.
You are operating the controller of the indoor unit that you want to release
from being the changeover master.
Home screen
30 ˚C
28
Press and hold button for 5 seconds or longer.
The information screen is displayed.
Information screen
12:34
Press (in that order) and hold them down for
10seconds.
The installer menu screen is displayed.
Installer menu screen
Navigate to the Rel Master Control menu “ ”.
01_EN_3P607378-2B_IM-K.indd 14 2020/07/28 11:39:54

15
Sub-menu screen
Press to release the indoor unit from its authority.
Result:
• The indoor unit is released from its authority.
• The controllers of all indoor units display a blinking
“” icon.
01_EN_3P607378-2B_IM-K.indd 15 2020/07/28 11:39:54

16
Setting up the changeover master
This setting is available only when none of the remote control in the system has master
control.
Prerequisite: No indoor unit is yet set as the changeover master (“ ” icon blinking on
all controllers).
You are operating the controller of the indoor unit that you want to set as the
changeover master.
30 ˚C
28
Menu screen
Navigate to the operation mode menu.
Sub-menu screen
Press or .
Result:
• The indoor unit is now the changeover master (“ ”
icon not displayed).
• All sub controllers display the “ ” icon.
01_EN_3P607378-2B_IM-K.indd 16 2020/07/28 11:39:55

17
Field Setting
Field settings method
This section describes how to perform eld setting.
Home screen
30 ˚C
28
Press and hold button for 5 seconds or longer to
display the information screen.
Information screen
12:34
Press (in that order) and hold them down
for 10seconds to display the installer menu screen.
Installer menu screen
Press or button, for move to “ ”.
If Bluetooth is connected, performing eld setting from
the remote controller side is impossible.
Disconnect Bluetooth, or perform eld setting from the
mobile application.
Sub-menu screen
Mode 20
Unit 00
a
b
c
d
Press or button, to select Mode No. and press
to enter the eld setting menu.
Press or button, to scroll the desired Mode No.
and press button.
a Mode No.
b Unit No.
c Enter
d Return
01_EN_3P607378-2B_IM-K.indd 17 2020/07/28 11:39:57

18
Sub-menu screen
Mode 20
Unit 00
Press or button, to select Unit No. and press
button.
Press or button, scroll to the desired Unit No. and
then press button to set the selection.
Sub-menu screen
Mode 20
Unit 00
Press or button, to select , and then press
button to set the selection.
Sub-menu screen
SW 00
–01
a
b
Press or button, select First Code No., and then
press button.
Press or button, scroll to the desired First code
No. and then press button to set the selection.
a First Code No.
b Second Code No.
Sub-menu screen
SW 00
–01
Press or button, to move Second Code No., and
then press button.
Press or button, to scroll to the desired Second
Code No., and then press button.
01_EN_3P607378-2B_IM-K.indd 18 2020/07/28 11:39:59

19
Sub-menu screen
SW 00
–01
Press or button, select , and then press
button to x the setting and return to the previous
screen.
If the setting is not changed, select .
Sub-menu screen
Mode 20
Unit 00
Press or button, move to , and then press
button to return to the installer menu.
* If the setting has been changed, the screen may
return to the home screen without returning to the
installer menu.
CAUTION
• The connection of optional accessories to the indoor unit might cause changes to some eld
settings. For more information, see the installation manual of the optional accessory.
• For details about the specic eld settings of each type of indoor unit, see the installation manual
of the indoor unit.
• Field settings that are not available for a connected indoor unit are not displayed.
• Field setting default values are dierent depending on the indoor unit model. For more information,
see the service manual of the indoor units.
01_EN_3P607378-2B_IM-K.indd 19 2020/07/28 11:40:00