Dakota Digital CMD-1000 User manual

REMOTE UP/DOWN WINDOW CONTROL
Or LOCK/UNLOCK CONTROL
CMD-1000
Thank you for purchasing the Remote Window Control from Dakota Digital. These units have been
designed to universally interface to virtually any power window regulator or door lock system on the market.
This system will raise and lower one power window or lock and unlock the doors. A third channel can also
be used for a trunk latch release or other 12 volt accessory.
Mounting:
The receiver module should be mounted up under the dash on either the drivers side or the
passenger side of the vehicle. Plug in the 10 pin harness to the mating connector on the control module.
Route the antenna lead as high as possible behind the dash and as far across as possible. Do not coil it or
wrap it around an existing wiring harness. The receiver module is not sealed and should not be mounted
where it can be exposed to water.
Wiring:
Connect the RED power wire to constant-on +12 volts and the BLACK wire to chassis ground.
Connect the remaining wires to relays according to the wiring diagram specific to your type of application.
There are two types of power window switches commonly used. One type switches the power to the
window regulator directly. When the switch is at rest, it keeps both of the window regulator wires grounded.
The other type switches 12 volts only to a relay pack and the relay provides the power to the window
regulator. Your remote window control system wires differently depending on the type of the switch that is
being used.
Window Control Operation:
To operate the window, press button #1. As long as the button is held, the window will continue to
move. To stop the window at any point of its travel, simply release the button. The window direction can
then be reversed by pressing button #2. Button #3 can activate a relay for a trunk latch release or other 12
volt accessory. Channel 3 has a three-second delay before it turns on.
Lock/Unlock Control Operation:
To unlock the door, press button #1. As long as the button is held, the door motor will be powered.
The button should only be held a few seconds to prevent damaging the door motor. To lock the door, press
button #2. Button #3 can activate a relay for a trunk latch release or other 12 volt accessory. Channel 3
has a three-second delay before it turns on.
The electrical operation of the system is as follows:
Button pressed
None WHITE, GREEN, and ORANGE wires are open (floating).
#1 GREEN wire is grounded to activate a relay.
#2 ORANGE wire is grounded to activate a relay.
#3 WHITE wire is grounded to activate a relay.
1

BLACK
The two wires from the switch to the motor must be cut and seperated, then connected to the relay pack.
Connection to Ball's, GM, Specialty,
Dakota Digital, Springfield Street Rod,
and similiar power window systems.
+12V BATTERY
GROUND
WHITE
CHANNEL 3
small wire small wire
RED
ORANGE
GREEN
+12V BATTERY
GREEN
GREEN WHITE BROWN BLUE
RED
BLACK
BLUEPURPLE
RECIEVER
MODULE
DAKOTA DIGITAL
ANTENNA
do not connect
to anything
WHITE
WHITE
POWER WINDOW
CENTER GROUND BLACK TO MOTOR
WHITE TO MOTOR
BLACK TO SWITCH
WHITE TO SWITCH
+12V BATTERY
BLACK
SWITCH
GND GND
+12V
REGULATOR AND SWITCH
NOT INCLUDED
2

DAKOTA DIGITAL
+12V BATTERY
GROUND BLACK
+12V BATTERY
GROUND
GROUND
DO NOT CONNECT WINDOW MOTOR WIRESPOWER WIRES
RED
GREEN
small wire GREEN
small wire
BLUE ORANGE
GREEN
BLACK
POWER WINDOW
WHITE
4-WIRE
SWITCH
BROWN
CHASSIS
PURPLE
BLUE
BLUE
DAMAGE THE REMOTE CONTROL UNIT!
NOTE THAT +12V WIRE ON POWER WINDOW SWITCH IS NO LONGER CONNECTED. CONNECTING A +12V WIRE TO THE SWITCH WILL
BLUE BLACK
Connection to 4-wire, center open
power window switches. RECIEVER
MODULE
ANTENNA
do not connect
to anything
CHANNEL 3 WHITE
RED
+12V BATTERY
3

4
RED CHANNEL 3
+12V BATTERY
GROUND
WHITE
BROWN GREEN
BLUE
PURPLE
+12V BATTERY
GREEN ORANGE
GREEN
small wire
RED
small wire
BLUE
BLACK
DO NOT USE DO NOT USE
+12V BATTERY
+12V BATTERY
POWER WINDOW SPLICE
UP
DOWN
SWITCH
WHITE
DAKOTA DIGITAL
ANTENNA
do not connect
to anything
RECIEVER
MODULE
On 3-wire switches that
connect directly to the
motor, disregard the box
shown between the switch
and motor.

DAKOTA DIGITAL
BROWN
GROUND GREEN
GREEN
small wire
WHITE
Connection to door lock motors
directly without a switch.
+12V BATTERY
ANTENNA
do not connect
to anything
BLACK
+12V BATTERY
ORANGE
BLUE
RED
small wire
WHITE
CHANNEL 3
GROUND
BLUE
GREEN
PURPLE
+12V BATTERY RED
RECIEVER
MODULE
5

DAKOTA DIGITAL
+12V BATTERY
ORANGE
GREEN
small wire GREEN
WHITE
GROUND
Connection to door lock motors with a
5-wire switch.
ANTENNA
do not connect
to anything
BLUE
small wire
RED
CHANNEL 3 WHITE
RED
BLACK
+12V BATTERY
BLUE
BROWN
GREEN
PURPLE
+12V BATTERY
GROUND
RECIEVER
MODULE
+12V (BATT)
GROUND
SWITCH
5-WIRE
6

DAKOTA DIGITAL
Connection to factory door
lock motors with a 3-wire
switch. RECIEVER
MODULE
+12V BATTERY
LOCK SYSTEM FACTORY DOOR
DO NOT CONNECT
BLACK
GROUND
RED +12V BATTERY
GREEN
small wire
GREEN
ORANGE
BLUE
small wire
ANTENNA
do not connect
to anything
WHITE
CHANNEL 3
+12V BATTERY RED
+12V
DOOR LOCK SWITCH
GND
GND
7

WHITE
(black)
RECIEVER
MODULE
+12V BATTERY
* wire colors listed in
( ) arefor alternate
relay sockets found
in some units.
+12V BATTERY
FUSED +12V
do not connect
CHANNEL 3 OUTPUT BLACK
(yellow)
GREEN
(brown)
BLACK
BLUE
(Orange)
GROUND
RED
RED
Using Channel 3
for a trunk latch
release or other
12 volt
accessory.
ANTENNA
do not connect
to anything
GREEN
CHANNEL 3
WHITE
ORANGE
DAKOTA DIGITAL
BATTERY REPLACEMENT
Should the transmitter function become weak or erratic, the battery in the keychain transmitter may be weak. An indication of a weak battery is that the red indicator may have a dim glow
to it when either button is pressed. If this occurs, first check the system by using the second transmitter provided. If the second transmitter function properly,replace the battery in the
defective transmitter by the following method:
A. Remove the small screw on the back of the transmitter case.
B. Carefully separate the two case halves.
C. Remove the battery noting the (+) and (-) position.
D. Replace the battery with a new 12 volt type GP23A battery which is available at most electronic stores (Radio Shack, etc.).
E. Carefully replace the top cover and refasten the screw.
F. Check transmitter function. Should the transmitter still fail to function, contact Dakota Digital, Inc..
CMD-1000 REMOTE UP/DOWN WINDOW CONTROL
LIMITED LIFETIME WARRANTY
DAKOTA DIGITAL, Inc. (the Company) warrants to the ORIGINAL PURCHASER of this remote control product that should any included control relay(s), electronic module, or
transmitters under normal use and condition, be proven defective in material or workmanship DURING THE LIFETIME OF THE CAR IN WHICH IT WAS ORIGINALLY INSTALLED, such
defect(s) will be repaired or replaced (at the Company's option) without charge for parts or labor directly related to repairs of the defect(s).
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s),
transportation prepaid, to the factory. This Warranty is valid for the original purchaser only and may not be transferred.
This Warranty does not cover batteries, nor extend to damage to vehicle electrical system. This Warranty does not apply to any product or part thereof which in the opinion of the
Company has been damaged through alteration, improper installation, mishandling, misuse, neglect, or accident.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE
LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. No person or representative is
authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
The Company does not warrant that this product cannot be compromised or circumvented. THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO
THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER FOR
THE PRODUCT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if incidental or consequential damage so the above limitations or exclusion may
not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
8
4510 W. 61ST St. N., Sioux Falls, SD 57107
Phone: [phone] FAX: [phone]
www.dakotadigital.com
[email protected]
©Copyright 2004 Dakota Digital Inc.