Dakota Digital LED Tail Lights LAT-NR401 User manual

MAN#650234
INSTALLATION INSTRUCTIONS
LAT-NR401
LED Tail Lights for 1977-78 Impala
MAN#650234
Kit Includes:
Installation:
1. Remove the original bulb connector from the back side of the housing.
2. Remove the tail light housing from the car.
3. Remove any body trim from the housing so the screws holding the lens on are exposed.
4. Remove the tail light lens.
5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is
recommended.
6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly.

MAN#650234
7. Insert the new LED assembly through the hole where the original bulb and connector were.
Use caution when feeding the wires through to avoid damaging the wire insulation.
8. Feed the wires through the large hole in the back plate and attach the back plate onto the back
side of the housing. The flat side of the mounting disk should be toward the outside and the
side with the slight raised center should go in toward the housing. This will align the mount in
the original housing.
9. Secure the back plate with the supplied #6 lock nuts.
10.Make sure the original lens gasket is in place and replace the tail light lens.
11.Replace the body trim and reinstall the tail light housing into the vehicle.
12.Cut off the existing light socket as it will not be used. Do not strip the wires. Trim the wires
from LED assembly to appropriate length once mounted, making sure wires are routed cleanly
and securely.
13.Use the supplied moisture resistant pigtail connectors* to attach the wires from the new LED
assembly to the existing vehicle harness. Insert appropriate wire from vehicle harness and
mating LED assembly wire into a connector and crimp following instructions below.
*For the best connection, soldering is recommended. But to simplify installation, the supplied connectors will
provide a fast weather resistant connection.
The correct crimp method for the supplied connectors is:
1.) Insert UNSTRIPPED wires into the connector and ensure they are all they way in by
observing the clear bottom of the connector to see the wires are touching the end.
2.) Use pliers to push the blue cap down flush with the edge of the clear body, completing the
connection. The connection will only be correct if pressed firmly down with pliers.

MAN#650234
GREEN wire
from LED
assembly
GREEN wire
from LED
assembly
Turn Signal wire
from vehicle
harness
BROWN wire
from LED
assembly
BROWN wire
from LED
assembly
Tail Light wire
from vehicle
harness
BLACK wire
from LED
assembly
BLACK wire
from LED
assembly
Ground wire
from vehicle
harness
LED wires
Vehicle harness
Tail light
Brown
Brown or Black
Driver’s Turn
Green
Green or Pink
Passenger’s Turn
Green
Yellow or Purple
Ground
Black
Chassis or body
14.Repeat for the other side.
15.Test the tail lights, brake lights, and turn signals. If the turn signals do not flash you will need
to upgrade your flasher. If you are replacing only the rear turn signals a heavy duty electronic
flasher from your local parts store should be able to be used. If you are replacing both front
and rear or do not have front bulbs you will need a no-load flasher, Dakota Digital part number
LAT-NLF.
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or
problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems.
Should you ever need to send the unit back for repairs, please call our technical support line, [phone], to request a Return Merchandise Authorization
number. Package the product in a good quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include the RMA
number on the package, and include a complete description of the problem with RMA number, your full name and address (street address preferred), and a telephone number
where you can be reached during the day. Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase. Send no money. We will
bill you after repair. Dakota Digital Limited Lifetime Warranty
DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and condition, be proven defective in material or
workmanship for the lifetime of the original vehicle it was installed in, such defect(s) will be repaired or replaced at Dakota Digital’s option.
This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover removal or reinstallation of the product. This Warranty does not
apply to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, neglect, or
accident. This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties, including any implied warranty of merchantability, shall be limited to
the duration of this written warranty. No person or representative is authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with the
sale of this product.
4510 W. 61STSt. N., Sioux Falls, SD 57107
Phone: [phone] FAX: [phone]
www.dakotadigital.com
[e-mail]
©Copyright 2006 Dakota Digital Inc.