Dancing Wings Hobby T-08 J3 User manual

T-08 J3 600mm Instruction Manual
Speci�ication
Wingspan: 600mm
Length: 395mm
Flying Weight≈135g
Tools Needed
1,机身组装
Assemble the Fuselage
2,机翼及尾翼组装
Motor: MM1404 2900KV
ESC: 2S 10A
Battery:2S 400-500mAh
Servo:2.5g*4
Propeller: 6inch
Radio≥4CH
Suggested Equipment
F1*2
F5
F12
F2
F4 F6 F7 F8
F9
C1
F3-2
F3-1*2
F5-1*2
1
1
2
2
3
4
5
6
7
3
F1-1
轻木条
从预留孔穿入，并按实际长度截取。
C1
C5
C6
F11
C2
C3
C4
F13
粘贴磁铁
W6
W5
W4
W3
W1 W9 D1
W11 W14 W15
W2
W10 W15-1
W13
W13-1
W12
W16
W16
1.5mm
W6
W7
W8
8
9
10
11 12
14
16
15
17
13
F2-1
如图粘贴PVC挡风玻璃
X
When you install the motor,pls put X wood piece
to make it with suitable length as per you needs.
安装马达时，根据不同尺寸马达可垫
入X木片，已达到合适长度。
Balsawood strip
Insert from the reserved hole and cut
off as per the actual length.
轻木条
并按实际长度截取。
Balsawood strip
Cut off as per the actual length.
轻木条
从预留孔穿入，并按实际长度截取。
Balsawood strip
Insert from the reserved hole and cut
off as per the actual length.
Soak and paste the cover board C2.
C2蒙板粘贴时先用水湿润，再粘贴，以方便弯曲。
Paste the magnet
Paste the PVC window shield as picture shown.
Assemble the Wing and Tail Wing
轻木条
并按实际长度截取。
Balsawood strip
Cut off as per the actual length.
Carbon Rod
碳杆
拼装机翼时在平整的工作台进行拼装，并
保持机翼平直。
Assmble the wing on the smooth
desk,make sure the wing is straight.
工具
参数
推荐配置
马达：MM1404 2900KV
电调：2S 10A
电池：2S 400-500mAh
舵机：2.5g*4
桨叶：6inch
通道：≥4CH
翼展：600mm
机长：395mm
起飞重量：≈135g

W17
W17 碳杆
Carbon Rod
18 19 20
3,起落架安装图示
A1
A2
A3
A4
21 22
25 26
8,重心调试位置图示
C.G
≈23mm
F15*2
23 24
副翼配有三角木，也可用 拼装副翼，用纸合页连接到机翼
17
You could choose the supplied triangular wood as
aileron,and also could choose the built-up pieces in picture
NO.17 as aileron,then connect with wing by paper hinges. 在舵机舵臂上安装快装接头，
并在副翼上安装舵角，用 Z 型
钢丝连接舵角。
Install the servo horns at
suitable position on the
rudder and
elevator,connect the servo
horn with the Z-shape end
of the Z-shape steel wire.
完成的两片机翼用F15对插在一起，
连接处用胶水粘合加固。
Connect together the two half wings
with F15 and firm with glue.
Connect the elevator and rudder with tail
by paper hinges,make it removable.
Install the servo horns at suitable position
on the rudder and elevator,connect the
servo horn with the Z-shape end of the
Z-shape steel wire.
Insert the steel wire from the reserved
hole inside the fuselage,and intall with
X-shape.
升降舵和方向舵用纸合页连接到尾翼，
并使其可以自由摆动。
在升降舵和转向舵上适当位置安装舵角，
把Z型钢丝连杆Z型一头与舵角连接。
钢丝连杆从机身内预留孔穿入，并成X型
交错安装。
Assemble the Landing Gear
5,桨叶安装示范4,机翼安装到机身图示
自功螺丝
M2*10
27 28
Assemble the wing onto the fuselage Install the Propeller
桨叶用桨夹锁定到马达上。
Lock the propeller onto the
motor with prop adapter.
Adjust the C.G.
调整电子设备及重心即可进行试飞。
Adjust the electric equipment
and C.G,then test the flight.
机身内装入舵机，舵臂上安装快装接头，把Z型
钢丝连杆平直一头在快装接头上固定住。
Install the servos inside the fuselage,install
the EZ connector onto the servo arm,and
connect the EZ connector with the straight
end of the Z-shape steel wire.