Dancover Gazebo San Pablo 3x3m User manual

Manual
for
Gazebo San Pablo
3x3m, 3x4m and
4x4m
21-09-2020

Manual Instruction
3x3m, 3x4m, 4x4m
Pergola

Spare parts list
Column
Beam (Left)
Beam(Right)
Front and rear
beams
Middle beam
Flap
Column bottom
plate
Column cover
plate
Connectors for
middle beams
Hinge ring
Hand crank
Label No.
Part description
Drawing Qty
4
1
1
2
1
3x3=44
3x4=60
4x4=60
4
4
2
2
2
2

Label No.
Part description
Countersunk
head screw
Pan head
screw
Flat washer
Screw+nut
Glass glue
Woodworking screw+
plastic expansion pipe
Plastic jam
+Flat washer
Drawing Qty
40+2
20+2
8+2
2
16
1
3x3=88
3x4=120
4x4=120
M6x16
M6x16
D6x12
M4x25
3
M8x80
8
10x50

1. Install the bottom plate F on the column A,
and tighten the screw K1; complete 4 sets in sequence.
K1 QTY: 16PCS F QTY:4PCS
4

2. Match the connector H with one side of middle beam D,
then tighten the screw K1; then complete the other side.
K1 QTY:8PCS QTY:2PCS
H
5

3. Put two hinge rings I into the gearbox drive shaft on the beam D,
fix the screw + nut K4
QTY:2PCS QTY:2 SETS
IK4 M4 M4x25
6

4. Place the column and beam as shown in the figure,
and note that the drain port of the column faces the same side;
7
Drain port
Drain port
Drain port
Drain port

5. The two ends of one front and rear beam C are
respectively placed on the corner connectors
on the column, and the screws K1 are tightened;
K1 QTY:4PCS
8

6. The left and right beams B1/B2 are
connectors on the column, and respectively placed on the corner
the screws K1 are tightened;
K1 QTY:8PCS
9

7. Insert ends of the other front and rear beams C
into the corner connectors on the
column, and tighten the screws K1;
K2 QTY:4PCS
10

8.The 4 column cover plates G
are respectively mounted on
the corner connectors of the
column and the beam,
and the screws K2
are tightened in turn;
K2 QTY:12PCS QTY:4PCS G
11

9. Adjust the position of the four columns so that they are perpendicular to the ground.
Meanwhile, the width of the top of each two columns should be measured
in accordance with the width of the bottom of each two columns.
Then use a market pen to mark 16 holes on the ground,
which should be corresponding to the holes in the botton palte.
Mark the location of the hole
on the ground with
a marker pen
Use tools: marker pen
(self-provided by installation workers)
12

10. Remove the product from the mark and drill holes of
at 16 mark positions on the ground with a percussion drill.
Use Tools: Percussion Drill
(Self-provided by Installation workers) Use Tool: Percussion Bit
(Self-provided by Installation workers)
13
10x80
Drilling depth
Drilling quantity 16pcs
10x80
10

11. Place the plastic expansion pipe in the bottom hole of the column;
then move the product back to the hole drilled, align holes of the
column bottom plates with the hole drilled on the ground;
then set L1 into the woodworking screw L,
and fix it with the ground separately.
14

12. Coat the glass glue M evenly on the drain of column and joints of beams.
15

13. Place the middle beam D on the front and rear beams C.
16

14. Insert 6pcs flap (E) first (4pieces at gear box side and 2pcs at other side)
and press down on the slat as shown in the sketch below to secure it.
on the end of the brackets on both sides of the beams (B1-D and B2-D),
17

15.First, fix screw K2 with
gasket K3 align with hole
below the beam D,
then same to beam C.
Insert the other flap in turn.
18

16. Adjust according to below steps if the pergola can`t close completly
A: flap
B: flapsupport
Hole "A" and hole "B"
must be concentric
Adjust solution if hole"A" and hole "B" are not concentric
straight screwdriver
Adjusting the B flap support with
straight screwdriver as picture shown Hole "A“ and "B" are concentric after adjusting
19