Dancover San Francisco User manual

09-04-2021
for
Manual
Gazebo
San Francisco 3x3,65m

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is your
responsibility to comply with local rules and regulations and to ensure that the marquee/tent is
assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is safely
secured and that the marquee/tent does not cause damage to others.
Do not use open re, welding equipment or other sources which can ignite, inside or close to the
tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent with
straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow, always remove snow from the roof of the marquee/tent regularly to prevent
snow from building on the roof, as heavy snow can cause the marquee/tent to collapse.
In the event of rain, there is a risk of rain puddles building up on top of the roof of the marquee/
tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain
puddles do not build up. As a precaution, make sure the roof of the marquee/tent is stretched
out properly and adequately over the side frames of the marquee/tent and remove rain water
regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of temperatures
below zero, always unpack and repack your marquee/tent indoors to avoid the risk of cracking
parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Note: Marquees are intended for events and other arrangements and are as such only meant for
short term temporary assembly and the following disassembly. Dancover warranty applies only
to the normal use of the Product, normal wear and tear excepted, in accordance with written
use instructions or manual. The warranty does not apply to damage caused by accident, abuse,
misuse, or modication of the Product.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manual.

Part list for gazebo 3x3,65m

W
M6*30

up
STEP 3:Connect the Ionger Crossbeams Band B1 using Crossbeam
Connector (Part P) Note: After sliding the Cro ssbeam Connector (Part P)
into a crossbeam you should start one bolt to hold the Crossbeam
Connector in place.

STEP 5-1: Attach the Corner Protectors (Part J1)
and the Rib Supports (Part J2) Just twist the top
two screws of (Part J2)
STEP 5-2: Slide 5 Netting
Hooks (Part Q) into Long Crossbeams (Parts B
and B1).With the sections laying on their side,
Slide 4 Netting Hooks (Part Q) into Short
Crossbeams (Parts C and C1). Then Attach (Part M6)
Note: There are two tracks. You can choose
either track to install Part Q
STEP 5-2
STEP 5-1

STEP 6
STEP 6: Assemble the Roof Frame by Attaching the Roof Ribs
Long (Part E) to the Roof Top Brace (Part K1).

STEP 7
STEP 8

Don't tighten all the screws, just
hold the（ Part I and Part H）,
until all of them are fixed
W
Tap lightly with
the screwdriver
STEP 9
STEP 10
Please note that
Parts M3 are
installed on Parts
D, and Parts M4
are on Parts E.
/

G5/G6
STEP 11
Step11 - 1 ：Install the Roof Plates （Part N5 and N6) on the Long Sides of the Gazebo.
Install the Roof Plates （Part O5) on the Short Sides of the Gazebo.
Tighten the screw (part U) halfwy,then install(Part G5 G6), and finally tighten the (Part U)
Step11-2:
1 2 3
4
G5
G6
5
G5

T
STEP 12
STEP 13
T
Step 12: Part N1 N2 N3 N4 for the
Long Sides of the Gazebo, Part O1 O2
O3 O4 for the short Sides of the Gazebo.
Install the Roof Plates on the Long
Sides of the Gazebo. Start by sliding
Roof Plate 1 (Part N2 and N3) into
position. Then N1and N4. The same
for the other three sides.

STEP 14
Note: First fix 4 (Part M2) with V, but do not screw too tight, then install (Part G1 G2 G3
and G4 )as shown in the diagram. You'd better from left to right.
Attach the Center Rib Braces (PartM1) as shown in the diagram.

STEP 15
Gently insert Z2, Z3, Z4 from left to right as shown, then tighten
them via screws U1 and V.
G7
G8
G7 U1

STEP 16
6

I
For more information
please visit:
www.dancovershop.com
l
l
l
l
l
l
l
l
l
l
l
Dancover A/S
Lyngevej 16A, Nørre Herlev
3400 Hillerød
Denmark
Head office: