Dancover San Bernardino User manual

09-04-2021
for
Manual
Gazebo
San Bernardino 3x3m

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is your
responsibility to comply with local rules and regulations and to ensure that the marquee/tent is
assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is safely
secured and that the marquee/tent does not cause damage to others.
Do not use open re, welding equipment or other sources which can ignite, inside or close to the
tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent with
straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow, always remove snow from the roof of the marquee/tent regularly to prevent
snow from building on the roof, as heavy snow can cause the marquee/tent to collapse.
In the event of rain, there is a risk of rain puddles building up on top of the roof of the marquee/
tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain
puddles do not build up. As a precaution, make sure the roof of the marquee/tent is stretched
out properly and adequately over the side frames of the marquee/tent and remove rain water
regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of temperatures
below zero, always unpack and repack your marquee/tent indoors to avoid the risk of cracking
parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Note: Marquees are intended for events and other arrangements and are as such only meant for
short term temporary assembly and the following disassembly. Dancover warranty applies only
to the normal use of the Product, normal wear and tear excepted, in accordance with written
use instructions or manual. The warranty does not apply to damage caused by accident, abuse,
misuse, or modication of the Product.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manual.

Part list for gazebo 3x3m
A4
B4
4
4
No Qty
C4
Qty
No
D
4
E
4
F
4
F1
4
G1
G2
8
H
4
4
J
1
J1
L4
M1 4
M2 4
M3 4
M4 4
M5
P
4S
M6*10 32
X
5*12
X1
Y
T1
4
W
M6*47
M6*25
M6*42
Z1
1
Q
4
856
56
64
32
1
R1
R
16
56
4
N
K
K1
M6 1
x4 x4 x4 x4
VM6*15 96
1
M6*50

AL
V
F
F1
Y
Y
Y
Y
X
X
STEP 1
STEP 2
STEP 1:Attach Foot Base ( Part L) to the Pillars (Part A)
STEP 2:Attach Crossbeams 1 (Part B) and Crossbeams 4
(Part C) to Pillars (Part A). Attach Support Brackets (Parts F
and F1) to Crossbeam and Pillar. Attach Crossbeams 2
(Part C) and Crossbeams 3 (Part B) to Pillars (Part A). Attach
Support Brackets (Parts F and F1) to Cross Beam and Pillar.
B
C
A
C
B
A
C
A
B
B
A
C
F1 F
F1
F
F1
F
F1
F
You can put Part A down
lf the screw hole is out of
alignment, pull adjusting
part B or C

C
B
A
B
A
C
P
V
B
A
C
C
A
B
C
B
A
B
A
C
P
P
STEP 3:Connect the Crossbeams B and C using
Crossbeam Connector (Part P) Note: After sliding the
Crossbeam Connector (Part P) into a crossbeam you should
start one bolt to hold the Crossbeam Connector in place.
Step 4: Stand both sides Upright and Connect
Crossbeams B and Crossbeams C using the
Crossbeam Connectors (Part P).
UP
STEP 3
STEP 4

QQ
Y
Y
J
YYM6
B
C
B
C
J
B
C
B
C
QQ
YYM6
STEP 5-1: Attach the Corner Protectors (Part J)
and the Rib Supports (Part J1) Just twist the top
two screws of (Part J1)
STEP 5-2: Slide 4 Netting Hooks (Part Q) into
Crossbeams (Parts B and C). Then Attach (Part
M6) Note: There are two tracks. You can choose
either track to install Part Q
M6
STEP
5-1
STEP
5-2
J1

E
E
E
E
K1
V
V
E
E
E
E
V
K1
STEP 6:Assemble the Roof Frame by Attaching the Roof
Ribs Long (Part E) to the Roof Top Brace (Part K1).
STEP 6

E
E
E
E
K1
D
V
D
V
D
D
D
D
D
D
D
V
E
STEP 7:Lift the Partially assembled
Roof on to the assembled Frame and
attach.
STEP 8:Attach the Roof Ribs Short (Part D) to the Roof Top Brace
(Part K1). Attached the Roof Ribs Short (Part D) to the assembled
frame.
STEP 7
STEP 8

H
H
H
H
H
H
V
M3
V
H
HM4
E
H
H
W
D
M3
M4
M3
STEP 9:Attach the Roof Supports 1
(Part H) to the roof frame using
Connectors 1 (Part M3) and
Connectors 2 (Part M4).
E
M4
Don't tighten all the screws,
just hold the (Part H), until all
of them are fixed
Please note that
Parts M3 are
installed on Parts D,
and Parts M4 are on
Parts E.
Step 10:Attach the Clips (Part R1)
and Clips (Part R) as shown in the
diagram.
Tap lightly with
the screwdriver
R/R1
x4 x4 x4 x4
R1
R
R
R
R
R
R
R
R1
R1
R
R
R
R
R
R
R
R1
STEP 9
STEP 10

G1
G2 G1 G2
M2
M2
M2
M1 M1
K1
K
M6
2
S
M5 W
If the screw hole is out of
alignment, insert it with a
screwdriver and correct it
V
M2
G1
G1
G2
VG3
G1
G2
M1
V
M1
M2
M2
STEP 11
STEP 12
M5
T
X1
X1
4
3
1
3
2
2
43
O4 O3 O2
O1
K
T
5
1
G1/G2
Note: First fix 4 (Part M2) with V, but do not screw
too tight, then install (Part G1 and G2 )as shown in
the diagram. You'd better from left to right. Attach
the Center Rib Braces (Part M1) as shown in the
diagram.
Step 11: Install the Roof Plates Part O1 O2 O3 O4 on
the Gazebo. Start by sliding Roof Plate1
(Part O2 and O3) into position. Then O1and O4. The
same for the other three sides.

Z1
Z1
Z1
Z1
Q
STEP 13: Install the Mosquito Netting as Shown in the
Diagram
Z1
STEP 13

I
For more information
please visit:
www.dancovershop.com
l
l
l
l
l
l
l
l
l
l
l
Dancover A/S
Lyngevej 16A, Nørre Herlev
3400 Hillerød
Denmark
Head office: