Danfoss AMV 110 NL AQT User manual

1
VD.LE.A6.02 © Danfoss 01/2014
DEN-SMT/SI
Actuators for three point control
AMV 110 NL, AMV 120 NL
Data sheet
Description The actuators are used together with
automatically balanced combination valve type
AB-QM for DN 10 to DN 32.
Typical applications for that products are:
temperature control and permanent automatic
balancing on terminal units (fan-coils, chilled
ceilings, air-handling units..).
Main data:
• Gap detection at stem up position
•3 point version
•Force switch-off at stem down position
prevents overload of actuator and valve
•No tools required for mounting
•Maintenance-free lifetime
•Low-noise operation
•Halogen free cables
Ordering Actuators
Type Supply voltage Speed Cable length Code No,
(V) (s/mm) (m) Single Pack Industry Pack
AMV 110 NL
24 AC
24
1,5 082H8056 /
5,0 082H8080 082H8076
10 082H8090 082H8086
AMV 120 NL 12
1,5 082H8058 /
5,0 / 082H8078
10 /082H8088
Note:
Actuators with 5 m and 10 m cable length are produced on request. Please note this increases lead time.
Spare parts
Type Length
(m) Code No.
Cable (24 V) 5082H8052
10 082H8054

2VD.LE.A6.02 © Danfoss 01/2014
DEN-SMT/SI

Data sheet Actuators for three point control AMV 110 NL, AMV 120 NL
Installation Mechanical
The actuator should be mounted with the valve
stem in either horizontal position or pointing
upwards.
The actuator is fixed to the valve body by means
of a mounting ring, which requires no tools for
mounting. The ring should be tightened by hand.
Electrical
Important: It is strongly recommended that the
mechanical installation is completed before the
electrical installation.
Each actuator is supplied with the connecting
cable for the controller.
Disposal The actuator must be dismantled and the
elements sorted into various material groups
before disposal.
Technical data
Type AMV 110 NL AMV 120 NL
Power supply V 24 AC, +10 to –15 %
Power consumption running VA 1
standby W 0
Frequency Hz 50 Hz/60 Hz
Close of force N 130
Stroke mm 5
Speed s/mm 24 12
Relative humidity max. 80 %
Max. medium temperature
°C
120
Ambient temperature 0 … 55
Storage and transport temperature –40 … 70
Protection class III safety extra-low voltage
Grade of enclosure IP 42
Weight kg 0,3
- marking in accordance with
standards
Low Voltage Directive (LVD) 2006/95/EC: EN 60730-1, EN 60730-2-14
EMC Directive 2004/108/EC: EN 61000-6-2, EN 61000-6-3
Wiring

3
VD.LE.A6.02 © Danfoss 01/2014
DEN-SMT/SI
position
indicator
⑤
①
②
③④
Data sheet Actuators for three point control AMV 110 NL, AMV 120 NL
Commissioning The factory setting of the spindle is the fully
stem up position because of easier mechanical
connection of the actuator on the valve.
1. Check the valve neck. The actuator should be
in stem up position (factory setting). Ensure
that the actuator is mounted securely on the
valve body
2. Wire the actuator according to the
wiring diagram
3. The direction of the stem movement can be
observed on the position indicator
Installation and
commissioning procedure
(if required)
Do not touch anything on
the PCB!
Do not remove the cover
before the power supply is fully
switched off.
Manual override
(for service purposes only)
Caution:
Do not manually operate the
drive if power is connected!
Do not dismount the actuator
from the valve when it is in a
stem down position!
If dismounted in a stem down
position, there is a high risk that
the actuator gets stuck.
• Removecover①
• Pressandholdthebutton②(on the
bottom side of the actuator) during manual
override ③
• Replacecover④
• Installactuatoronvalve⑤
Remark:
A ‘click’ sound after energising the actuator
indicates that the gear wheel has jumped into
normal position.

4
VD.LE.A6.02
Produced by Danfoss A/S © 01/2014
Data sheet Actuators for three point control AMV 110 NL, AMV 120 NL
Dimensions (mm)