Danfoss TM70 User manual

Danfoss does not take responsibility for incorrect installation or
any frequency interference.
Chance of unintended machine movement on start up.
Ensure the machine is stopped for the entire duration of the
assembly process.
Keep the work area free and wear protective clothing.
Connect the power supply and the output connections using
the connection block diagram provided with the system. The
receiver will enter into scanning mode and show the following:
ORDER
RELAY
ID
DATA
SIGNAL
HARDOK
POWER
CANRUN
CANERR
OFF
ON
BLINKING
LED scanning mode (receiver)
LED Description
DATA There is not another system active
in the area
SIGNAL OFF; channels are signal free
BLINKING; RF signal detected on
the channels
HARDOK GREEN; Absence of faults on the
boards
POWER Power supply OK
CANRUN Communications with expansion
boards are OK*
*Only in receivers with CAN connection (except RCAN)
OUT
IN
RF signal detected
Incorrect ID signal from Ikusi system
CORRECT ELEMENTS
Abc
AbcINCORRECT ELEMENTS -Check
troubleshooting guide
Display scanning mode (receiver)
1. Place a charged battery in the transmitter
2. Turn the contact key
3. Push and pull out the STOP button
The LED of the transmitter will flash orange-green. If the
transmitter has a display, it displays the identification of the
machine, as well as the battery level
4. Press the start button
The green LED should now light indicating the transmitter
is transmitting
5. Turn off the transmitter using the STOP button
ORDER
RELAY
ID
DATA
SIGNAL
HARDOK
POWER
CANRUN
CANERR
OFF
ON
BLINKING
LEDs operational mode (receiver)
OUT
IN
Correct ID (the icon shows the quiality of the link)
Linked state
No Ikusi RF signal detected(the icon shows the
quality)
Incorrect ID ( the icon shows the quality)
Display operational mode (receiver)
Installation Guide
Remote Control
TM70 and Ikontrol
©Danfoss | January 2019 AI293579926818en-000101 | 1

1
2
3
4
5
6
7
8
9
TM70 hand-held transmitter
1. Label for crane identification
Optional: display LCD
2. LED
3. Maneuver button
4. Contact key
5. Start button
6. STOP button
7. Optional: range limiter
8. Battery
9. Removable EEPROM
5
1
2
3
6
78
4
10 9
11
12
Ikontrol console box transmitter
1. Label for crane identification
2. LED
3. Maneuver element
4. Contact key or multi-key
5. Start button
6. STOP button
7. Optional: range limiter
8. 3.5" color TFT display (IK3); LCD monochrome 128x64
(IK2)
9. Removable EEPROM
10. Tether connection
11. Lateral push buttons
12. Battery
Contact key
Insert the multi-key and turn the position from 0 to 1. The
machine will not operate in 1 position as this is the natural
position of the multi-key.
Start/horn
In position 1, release the STOP push button and push start so
the transmitter starts emitting. The multi-key can also be used
to activate maneuvers such as the horn signal.
Toggle switch
The multi-key can also work as a toggle switch, configurable up
to 5 positions.
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
2 | ©Danfoss | January 2019 AI293579926818en-000101