Danfoss Link RS User manual

Danfoss Link™ RS
Installation Manual
MAKING MODERN LIVING POSSIBLE
Danfoss Heating
INT

Danfoss Link™ CC
Danfoss Link™ FT
2
Danfoss Link™ RS
Ambient temperature
Floor temperature
Communication/link test
Battery warning
Tamper proof. Locked by CC
The Danfoss Link™ RS (Room Sensor) has a built-in tem-
perature sensor which measures the ambient temperature.
It allows you to control the heating based on room tem-
perature, in the room where installed. With the Danfoss
Link™ RS you can also adjust the temperature.
Installation scenario:

3
Placement of Danfoss Link™ RS
Not on a wall where it will be subjected to
direct sunlight.
Installation height should typically be between
80-150 cm.
In wet rooms it should be installed on an
even surface, according to local building
regulations.
At least 50 cm away from windows/doors that
will be left open occasionally.
Not on the inner side of a wall facing the
outside.

4
Installation of Danfoss Link™ RS
1. Remove the front cover by gently
pressing the release tab on the
bottom side of the sensor.
2. Mount the room sensor
a. Mark up drill holes
b. Drill holes
c. Place fixing plugs in holes
d. Screw mount the RS
3. Mount batteries
4. Put front cover on by placing the
top of the cover in place first and
then gently press the bottom end
in place.
Configuration:
See Step-by-Step guide in Danfoss Link™ CC instruction
manual.

5
Trouble shooting
Short green flash Not included in network
Green fast flash Inclusion in progress
Red flash +
for 5 sec. Inclusion failed
ON Link test in progress
Red flash +
for 5 sec. Link test failed
ON + Red LED
flash every 2½ min. Low battery level
ON + Red LED
flash every 30 sec. Critical battery level
E5 Floor sensor short circuited
E6 Floor sensor lost
ON Tamper proof enabled by
Danfoss Link™CC
Flash Limited by Danfoss Link™CC
Factory reset a Danfoss Link™ RS:
Take the front cover off . Take out one battery and hold
the ON/OFF/Install button down while reinserting the
battery. Keep holding down the install button until it
flashes (approx. 5 sec.)

6
Battery Alkaline 2xAA, 1.5V
Battery lifetime Up to 4-5 years
Backlight Green LED
Ambient tempera-
ture
0˚ to +40˚C
Battery monitoring The sensor has a built-in
monitoring circuit, which will
detect low or critical battery
level.
Transmission
frequency
868.42MHz
Transmission range
in normal buildings Up to 30m
Transmission power Max. 1 mW
IP class 21
Dimensions 81 mm x 66 mm x 21 mm
Disposal Instruction:
Equipment containing electrical components should not
be disposed together with domestic waste.
It must be collected separately with other electrical and
electronic waste according to local legislation.
Technical specifications

7
The 2 Year Danfoss Warranty
You have purchased a Danfoss heating system
which we are sure will serve to improve the com-
fort and economy of your application.
Danfoss provides superior electrical heating
solutions for total climate control in and around
homes and buildings. Danfoss offers a complete
product program with Danfoss heating cables
or Danfoss heating mats, Danfoss thermostats,
Danfoss selflimiting heating cables combined
with additional products completing the product
program.
This 2 year warranty applies to all Danfoss prod-
ucts.
Should you, against all expectations, experience
a problem with your Danfoss product, you will
find that Danfoss offers a 2 year warranty from the
date of purchase on the following conditions:
During the warranty period Danfoss shall offer a
new comparable product or repair the product in
case the product is found to be faulty by reason
of defective design, materials or workmanship.
Repair or replacement shall be carried out at Dan-
foss’ discretion. Danfoss shall not be liable for any
consequential or incidental damages including,
but not limited to, damages to property or extra
utility expenses.
This warranty shall only be valid on production of
proof of purchase and must be submitted to the
installer or seller without undue delay.
An extension of the warranty period following
repairs undertaken under warranty cannot be
granted.
The Danfoss Warranty shall not cover any damage
caused by incorrect conditions of use, incorrect
installation or if installation has been carried out
by non-authorised electricians. All work will be
invoiced in full if Danfoss is required to inspect
or repair faults that have arisen as a result of any
of the above.
The Danfoss Warranty shall not extend to equip-
ment which has not been paid in full.
Danfoss will, at all times, provide a rapid and ef-
fective response to all complaints and inquiries
from our customers.
The warranty explicitly excludes all claims exceed-
ing the above conditions.
Attention:
The Warranty Certificate must be completed correctly for the Warranty to be valid.
Please read the Warranty conditions above.
The Danfoss™ Warranty is granted to:
Name:
Telephone:
Warranty Certificate
Address:
City:
Type of thermostat:
Article number: Date:
Suppliers Stamp:
Country:
Electrical installation by:

Article No.: 088L8082
Version - 01.01
Danfoss A/S
DK • 7100 Vejle
Phone [phone]
Fax [phone]
Danfoss Heating Solutions VIFZA102 © Danfoss 09/2009