Datalogic S70 User manual

1
A model with a QD connector requires a mating cordset.
1
S70 Series
Advanced sensor with dual digital displays
for use with plastic and glass fiber optic assemblies
For complete technical information about this product, including dimensions, accessories, and specifications, see www.datalogic.com.
Figure 1
WARNING: Not to be used for personnel protection
Never use this device as a sensing device for personnel protection.
Doing so could lead to serious injury or death. This device does not include the self-checking redundant
circuitry necessary to allow its use in personnel safety applications.
A sensor failure or malfunction can cause either an energized or de-energized sensor output condition.
Outputs Connector1
S70-2-E1-N Single NPN
2 m cable, 4-wire
S70-2-E1-P Single PNP
S70-5-E1-N Single NPN
Integral M8 Pico QD connector, 4-pin
S70-5-E1-P Single PNP
S70-5-E1-PZ Dual outputs, 1 push-pull IO-Link and 1 PNP
(complementary outputs)
S70-5-E2-N Single NPN
Integral M8 Pico QD connector, 4-pin
S70-5-E2-P Single PNP
CONNECTIONS
NPN Version PNP Version
IO-Link Version
NOTE: Open lead wires must be connected to a terminal block.
1Output LED
2LO/DO Switch
3RUN/PRG/ADJ Mode Switch
4Lever Action Fiber Clamp
5Red Signal Level
6Green Threshold
7+/SET/- Navigation key
LOAD
LOAD
10-30 VDC
10-30 VDC
Remote
Programming (N.O.)
Remote
Programming (N.O.)
Key
1 = Brown
2 = White
3 = Blue
4 = Black
Pico
4
3
2
1
(
C/Q
)
Load 18-30 VDC
(
Q
)
Load
Load
Load

2
MOUNTING INSTRUCTIONS
Mount on a DIN Rail
1. Hook the DIN rail clip on the bottom of the S70 over the edge of
the DIN rail (1).
2. Push the S70 up on the DIN rail (1).
3. Pivot the S70 onto the DIN rail, pressing until it snaps into
place (2).
Remove from a DIN rail
1. Push the S70 up on the DIN rail (1).
2. Pivot the S70 away from the DIN rail and remove it (2).
INSTALLING THE FIBERS
Follow these steps to install glass or plastic fibers.
1. Open the dust cover.
2. Move the fiber clamp forward to unlock it.
3. Insert the fiber(s) into the fiber port(s) until they stop.
4. Move the fiber clamp backward to lock the fiber(s).
5. Close the dust cover.
Fiber Adapters
NOTE: If a thin fiber with less than 2.2 mm outer diameter is used, install the fiber adapter provided with the fiber assembly to
ensure a reliable fit in the fiber holder. Datalogic includes the adapters with all fiber assemblies.
Fiber Outer Diameter (mm) Adapter Color
Ø 1.0 Black
Ø 1.3 Red
Ø 2.2 No adapter needed
When connecting coaxial-type fiber assemblies to the amplifier, install the solid core fiber to the LED emitting port, and the multi-core
fiber to the PD receiving port for most reliable detection.
Move forward to release the fibers
Fiber Clamp
Fiber Receiver
Port
Fiber Emitter
Port
TO
FIBERS
TO
SENSOR
RECEIVER
EMITTER
Multi-core fiber
Single-core fiber

3
TOP PANEL INTERFACE
Opening the dust cover provides access to the top panel interface. The top panel interface consists of the RUN/PRG/ADJ
mode switch, LO/DO switch, +/SET/- Navigation key, dual red/green digital displays, and output LED.
RUN/PRG/ADJ Mode Switch
The RUN/PRG/ADJ mode switch puts the sensor in RUN, PRG (Program), or ADJ (Adjust) mode.
RUN mode allows the sensor to operate normally and prevents unintentional programming changes via
the +/SET/- button. PRG mode allows the sensor to be programmed through the display driven
programming menu (see Program Mode below).
ADJ mode allows the user to perform Expert TEACH/SET methods and Manual Adjust (see Adjust
Mode below).
LO/DO Switch
The LO/DO switch is used to select Light Operate or Dark Operate mode. In Light Operate mode, the
output is ON when the sensing condition is above the threshold (for Window SET, the output is ON
when the sensing condition is inside the window). In Dark Operate mode, the output is ON when the
sensing condition is below the threshold (for Window SET, the output is ON when the sensing condition
is outside the window).
+/SET/- Navigation key
The +/SET/- Navigation key is a 3-way button. The +/- positions are engaged by rocking the button left/
right.
The SET position is engaged by clicking down the button while the rocker is in the middle position. All
three button positions are used during PRG mode to navigate the display driven programming menu.
During ADJ mode, SET is used to perform TEACH/SET methods and +/- are used to manually adjust
the threshold(s). The Navigation key is disabled during RUN mode, except when using Window SET,
see Window SET.
Red/Green Digital Displays
During RUN and ADJ mode, the Red display shows the signal level and the Green display shows the
threshold.
During PRG mode, both displays are used to navigate the display driven programming menu.
Output LED
The output LED provides a visible indication when the output is activated.
Remote Input / IO-Link
For more information about how to perform TEACH/SET methods, to program the sensor remotely,
or to interface with the sensor via IO-Link, see the www.datalogic.com.
Run Mode
Run mode allows the sensor to operate normally and prevents unintentional programming changes.
The +/SET/- Navigation key is disabled during RUN mode, except when using Window SET, see Window SET.

diSP rEAd
Click SET
to enter choice list
DISPLAY
LOOP
diSP 1234
diSP 123P Eco 1234
Eco 123P
(display flips 180)
PROGRAMMODE
Menu
List
Return to Menu List
on display represents a “w” on display represents a “m”
Mode Switch
to “PRG”
Click SET to select and save a choice in any list
G
A
in SEL
Click SET
to enter choice lis
t
DISPLAY
LOOP
Auto GAin
Fixed Gain Set
1234 Gn 1 1234 Gn 2
1234 Gn 8
tcH SEL
Click SET
to enter choice list
DISPLAY
LOOP
2Pt tcH
dYn tcH
wind SEt
Lt SEt
dr SEt
CAL SEt
FctY dEF
Click SET
to enter choice list
DISPLAY
LOOP
no
yES
rESPSPd
Click SET
to enter choice list
DISPLAY
LOOP
xxx uS
xxx uS xxx uS xxx uS
for the value see
“Technical Data”
pag.17
Auto thr
Click SET
to enter choice list
DISPLAY
LOOP
oFF
On
OFF dLY
Click SET
to enter choice
0ms
(+) or (-)
to set value
9999 ms
OFF 1Sho
Click SET
to enter choice list
0 ms
(+) or (-)
to set value
9999 ms
SET
+
Navigation key
-
To scroll through menu lists: Press “+” or “-”
To enter a choice list or to select and save: Click SET
To exit a choice list without saving: Press and hold SET for 2 seconds
Program Mode
Program (PRG) mode allows the
following settings to be programmed
in the S70:
Press and hold SET to exit
choice
list without saving
S70-E1 Factory Default Settings:
4
S70-E2 Factory Default Settings:
OFSt Pct
Click SET
to enter choice list
min OFSt
10 Pct
(+) or (-)
to set value
999 Pct
On dLY
Click SET
to enter choice list
0ms
(+) or (-)
to set value
9999 ms
On 1Sho
Click SET
to enter choice list
0ms
(+) or (-)
to set value
9999 ms

5
SET Button: 0.04
s
econds  "Click"  0.8
s
econds
Remote Input: 0.04 seconds  T  0.8 seconds
ADJUST MODE
Sliding the RUN/PRG/ADJ mode switch to the ADJ position allows the user to perform Expert TEACH/SET methods and Manual Adjustment
of the threshold(s).
Two-Point TEACH
•Establishes a single switching threshold
•Threshold can be adjusted using "+" and "-" Navigation key (Manual Adjust)
Two-Point TEACH is used when two conditions can be presented statically to the sensor.
The sensor locates a single sensing threshold (the switch point) midway between the two taught conditions, with the Output ON condition on
one side, and the Output OFF condition on the other (see Fig.2).
Darkest Taught
Condition
Sensor positions
threshold midway
Lightest Taught
Condition
between taught conditions
Output OFF Output ON
Darkest
(no signal)
Position
adjusted by
Manual Adjust
Most Light
(saturated
signal)
Figure 2. Two-Point TEACH (Light Operate shown)
The Output ON and OFF conditions can be reversed by using the LO/DO (Light Operate / Dark Operate) switch
(see LO/DO Switch in Top Panel Interface).
Two-Point TEACH and Manual Adjust
Moves switching threshold value up or down to make adjustments
•Slide Mode switch to ADJ to enter Adjust mode
•Press "+" to increase; press "-" to decrease
- GREEN display shows the switching threshold value
- 2 seconds after adjustment, the GREEN display will flash 3 times to confirm
•Slide Mode switch to RUN to complete operation
Follow these steps to perform a Two-Point TEACH:
1. Enter Adjust mode.
Method Action Result
SET Button 2
Set the Mode switch to ADJ.
Display: Red - Signal Level;
Green -
Threshold
Remote Input 3No action is required; sensor is ready
for
the Two-Point TEACH method
NOTE: TEACH Selection must be programmed to 2Pt tcH (see Program Mode)
Remember: Manual adjustments are disabled when Auto Thresholds are ON
2
3

6
See Troubleshooting on page 16 for more explanation of the % Minimum Difference displayed after the Two-Point TEACH method
4
2. Teach the first condition.
Method Action Result
SET Button
a. Present the first condition.
b. Click the SET Navigation key
Display: Flashes "2Pt tch" then holds
on "1234 2nd"
Remote Input
a. Present the first condition
b. Single-pulse the remote input
NOTE: Negative pulse for NPN models, positive pulse for PNP models.
3. Teach the second condition.
Method Action Result
SET Button
a. Present the second condition.
b. Click the SET Navigation key.
TEACH Accepted
Displays alternate "PASS" and %
Minimum Difference4; Sensor returns
to Adjust mode
TEACH Not Accepted
Displays alternate "FAIL" and %
Minimum Difference4; Sensor returns
to Adjust mode
Remote Input
T
a. Present the second condition.
b. Single-pulse the remote input.
4. Return to Run mode.
Method Action Result
SET Button
Move the Mode switch to RUN
Display: Red - Signal Level;
Green -
Threshold
Remote Input No action is required; sensor returns to
RUN mode automatically
Dynamic TEACH
•Teaches on-the-fly
•Establishes a single switching threshold
•Threshold can be adjusted using "+" and "-" Navigation key (Manual Adjust)
Dynamic TEACH is best used when a machine or process may not be stopped for teaching. The sensor learns during actual sensing
conditions, taking multiple samples of the light and dark conditions and automatically setting the threshold at the optimum level (see Fig.3).
Darkest Taught
Condition
Sensor positions
threshold midway
Lightest Taught
Condition
between taught conditions
Output OFF Output ON
Darkest
(no signal)
Position
adjusted by
Manual Adjust
Most Light
(saturated
signal)
T
Figure 3. Dynamic TEACH (Light Operate shown)
The output ON and OFF conditions can be reversed using the LO/DO switch (see LO/DO Switch in Top Panel Interface).

7
SET Button: 0.04
s
econds  "Click"  0.8
s
econds
Remote Input: 0.04 seconds  T  0.8 seconds
5
6
Dynamic TEACH and Manual Adjust
Moves switching threshold value up or down to make adjustments
•Slide Mode switch to ADJ to enter Adjust mode
•Press "+" to increase; press "-" to decrease
- GREEN display shows the switching threshold value
- 2 seconds after adjustment, GREEN display will flash 3 times to confirm
•Slide Mode switch to RUN to complete operation
Follow these steps to perform a Dynamic TEACH:
1. Enter Adjust Mode.
Method Action Result
SET Button 5
Set Mode switch to ADJ Display: Red - Signal Level;
Green -
Threshold
Remote Input 6No action required; sensor is ready for
Dynamic TEACH method
2. Enter Dynamic TEACH.
Method Action Result
SET Button Click the SET Navigation key
Display: Flashes "dYn tch" then holds
on "1234 dYn"
Remote Input
T
Single-pulse remote input
3. Present ON and OFF Conditions.
Method Action Result
SET Button Present ON and OFF conditions
Display: Red - Signal Level;
Green -
Threshold
Remote Input Present ON and OFF conditions
Remember: Manual adjustments are disabled when Auto Thresholds are ON
NOTE: TEACH Selection must be programmed to dYn tcH (see Program Mode)

8
See Troubleshooting on page 16 for more explanation of the % Minimum difference displayed after the Dynamic TEACH method.
7
4. Exit Dynamic TEACH.
Method Action Result
SET Button Click the SET Navigation key
TEACH Accepted
Displays alternate "PASS" with %
Minimum Difference7, Sensor returns
to Adjust mode
TEACH Not Accepted
Displays alternate "FAIL" with %
Minimum Difference7, Sensor returns
to Adjust mode
Remote Input
T
Single-pulse remote input
5. Return to RUN Mode.
Method Action Result
SET Button Move Mode switch to RUN Display: Red - Signal Level;
Green -
Threshold
Remote Input No action required; sensor returns to
RUN mode automatically
Window SET
•Sets window thresholds that extend a programmable % offset above and below the presented condition
•All other conditions (lighter or darker) cause the output to change state
•Sensing window center can be adjusted using "+\" and "-" Navigation key (Manual Adjust)
•Recommended for applications where a product may not always appear in the same place, or when other signals may
appear
•See Program Mode in the user's manual for programming the Offset Percent setting (to increase/decrease the window size)
A single sensing condition is presented, and the sensor positions window thresholds a programmable % offset above and below the presented
condition. In LO mode, Window SET designates a sensing window with the Output ON condition inside the window, and the Output OFF
conditions outside the window (see Fig.4).
Sensing window
center adjusted by
Manual Adjust
Sensor positions
window thresholds
aprogrammable %
offset from the
presented condition
Darkest
(no signal)
Condition
Presented
Most Light
(saturated
signal)
Output OFF Output ON Output OFF
Figure 4. Window SET (Light Operate shown)
Output ON and OFF conditions can be reversed using the LO/DO switch (see LO/DO Switch in Top Panel Interface).

9
SE
T
Button: 0.04
s
econds  "Click"  0.8
s
econds
Remote Input: 0.04 seconds  T  0.8 seconds
See Troubleshooting on page 16 for more explanation of the % Offset displayed after the Window SET method.
8
9
1
0
Window SET and Manual Adjust
Moves sensing window center value up or down to make adjustments
•Slide Mode switch to ADJ to enter Adjust mode
•Press "+" to increase; press "-" to decrease
- GREEN display shows the sensing window center value
- 2 seconds after adjustment, the GREEN display will flash 3 times to confirm
•Slide Mode switch to RUN to complete operation
Follow these steps to perform a Window SET:
1. Enter Adjust Mode
Method Action Result
SET Button 8
Set Mode switch to ADJ
Display: Red - Signal Level;
Green -
Threshold
Remote Input 9No action re
q
uired
;
sensor is read
y
for Window SET method
2. SET Sensing Condition
Method Action Result
SET Button
• Present sensing condition
• Click the SET Navigation key
Threshold Condition Accepted
Displays read "wInd SEt" then
alternate "PASS" with % Offset10;
Sensor returns to Adjust mode
Threshold Condition Not Accepted
Displays read "wInd SEt" then
alternate "FAIL" with minimum %
Offset10 for sensing condition; Sensor
returns to Adjust mode
Remote Input
• Present sensing condition T
•
Single-pulse the remote input
1. Return to RUN Mode
Method Action Result
SET Button Move Mode switch to Run
Display: Red - Signal Level;
Green -
Window Center
(see Figure 5 for instructions on how to
display
upper and lower thresholds)
Remote Input No action required; sensor returns to Run
mode automatically
Window SET (during RUN mode)
Upon sensor power-up, Window Center is displayed
Upper Threshold Window Center Lower Threshold
Displayed Displayed Displayed
Remember: Manual adjustments are disabled when Auto Thresholds are ON
Note: TEACH Selection must be programmed to wind SEt (see Program Mode)
Figure 5. Upper and Lower Thresholds

10
SET Button: 0.04 seconds  "Click"  0.8 seconds
Remote Input: 0.04 seconds  T  0.8 seconds
11
12
Light SET
•Sets a threshold a programmable % offset below the presented condition
•Changes output state on any condition darker than the threshold condition
•Threshold can be adjusted using "+" and "-" Navigation key (Manual Adjust)
•Recommended for applications where only one condition is known, for example a stable light background with varying darker
targets
•See Program Mode for programming the Offset Percent setting
A single sensing condition is presented, and the sensor positions a threshold a programmable % offset below the presented condition.
When a condition darker than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO switch setting (see
LO/DO Switch in Top Panel Interface).
Threshold position
adjusted by
Manual Adjust
Sensor positions
threshold a programmable
% offset below the
presented condition
Output OFF Output ON
Darkest
(no signal)
Condition
Presented
Most Light
(saturated
signal)
Figure 6. Light SET (Light Operate shown)
Light SET and Manual Adjust
Moves switching threshold value up or down to make adjustments
•Slide Mode switch to ADJ to enter Adjust mode
•Press "+" to increase; press "-" to decrease
- GREEN display shows the switching threshold value
- 2 seconds after adjustment, the GREEN display will flash 3 times to confirm
•Slide Mode switch to RUN to complete operation
Follow these steps to perform a Light SET:
1. Enter Adjust Mode
Method Action Result
SET Button 11
Set Mode switch to ADJ
Display: Red - Signal Level;
Green -
Threshold
Remote Input 12 No action is required; sensor is ready
for
Light SET method
Remember: Manual adjustments are disabled when Auto Thresholds are ON
Note: TEACH Selection must be programmed to Lt SEt (see Program Mode)

11
See Troubleshooting for more explanation of the % Offset displayed after the Light SET method.
13
2. SET Sensing Condition
Method Action Result
SET Button
• Present sensing condition
• Click the SET Navigation key
Threshold Condition Accepted
Displays read "Lt SEt" then alternate
"PASS" with % Offset13; Sensor
returns to Adjust mode
Threshold Condition Not Accepted
Displays read "Lt SEt" then alternate
"FAIL" with minimum % Offset13 for
sensing condition; Sensor returns to
Adjust mode
Remote Input
• Present sensing condition T
•
Single-pulse the remote input
3. Return to RUN Mode
Method Action Result
SET Button Move Mode switch to RUN
Display: Red - Signal Level;
Green -
Threshold
Remote Input No action required; sensor returns to RUN
mode automatically
Dark SET
•Sets a threshold a programmable % offset above the presented condition
•Any condition lighter than the threshold condition causes the output to change state
•Threshold can be adjusted using "+" and "-" Navigation key (Manual Adjust)
•Recommended for applications where only one condition is known, for example a stable dark background with varying lighter
targets
•See Program Mode for programming the Offset Percent setting
A single sensing condition is presented, and the sensor positions a threshold a programmable % offset above the presented condition.
When a condition lighter than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO switch setting
(see LO/DO Switch in Top Panel Interface).
Threshold position
adjusted by
Manual Adjust
Sensor positions
threshold a programmable
% offset above the
presented condition
Output OFF Output ON
Darkest
(no signal)
Condition
Presented
Most Light
(saturated
signal)
NOTE: Offset Percent MUST be programmed to Minimum Offset to accept conditions of no signal (0 counts).
Figure 7. Dark SET (Light Operate shown)

12
SET Button: 0.04 seconds  "Click"  0.8 seconds
Remote Input: 0.04 seconds  T  0.8 seconds
See Troubleshooting on page 16 for more explanation of the % Offset displayed after the Dark SET method.
1
4
1
5
1
6
Dark SET and Manual Adjust
Moves switching threshold value up or down to make adjustments
•Slide Mode switch to ADJ to enter Adjust mode
•Press "+" to increase; press "-" to decrease
GREEN display shows the switching threshold value
2 seconds after adjustment, the GREEN display will flash 3 times to confirm
•Slide Mode switch to RUN to complete operation
Follow these steps to perform a Dark SET:
1. Enter Adjust Mode.
Method Action Result
SET Button 14
Set Mode switch to ADJ
Display: Red - Signal Level; Green -
Threshold
Remote Input 1
5
No action required; sensor is ready for
Dark
SET method
2. SET Sensing Condition.
Method Action Result
SET Button
• Present sensing condition
• Click the SET Navigation key
Threshold Condition Accepted
Displays read "dr SEt" then alternate
"PASS" with % Offset16; Sensor
returns to Adjust mode
Threshold Condition Not Accepted
Displays read "dr SEt" then alternate
"FAIL" with minimum % Offset16 for
sensing condition; Sensor returns to
Adjust mode
Remote Input
• Present sensing condition T
•
Single-pulse the remote input
3. Return to RUN Mode.
Method Action Result
SET Button Move Mode switch to RUN
Display: Red - Signal Level;
Green -
Threshold
Remote Input No action required; sensor returns to RUN
mode automatically
Remember: Manual adjustments are disabled when Auto Thresholds are ON
Note: TEACH Selection must be programmed to dr SEt (see Program Mode)

13
SET Button: 0.04 seconds  "Click"  0.8 seconds
Remote Input: 0.04 seconds  T  0.8 seconds
1
7
1
8
Calibration SET
•Sets a threshold exactly at the presented condition
•Threshold can be adjusted using "+" and "-" Navigation key (Manual Adjust)
A single sensing condition is presented, and the sensor positions a threshold exactly at the presented condition. When a condition lighter
than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO switch setting (see LO/DO Switch in Top Panel
Interface).
Threshold position
adjusted by
Manual Adjust
Sensor positions
threshold exactly at
the presented condition
Output OFF Output ON
Darkest
(no signal)
Condition
Presented
Most Light
(saturated
signal)
Figure 8. Calibration SET (Light Operate shown)
Calibration SET and Manual Adjust
Moves switching threshold value up or down to make adjustments
•Slide Mode switch to ADJ to enter Adjust mode
•Press "+" to increase; press "-" to decrease
- GREEN display shows the switching threshold value
- 2 seconds after adjustment, the GREEN display will flash 3 times to confirm
•Slide Mode switch to RUN to complete operation
Follow these steps to perform a Calibration SET:
1. Enter Adjust Mode
Method Action Result
SET Button 17
• Set Mode switch to ADJ
Display: Red - Signal Level;
Green -
Threshold
Remote Input 18 No action required; sensor is ready for
Calibration SET method
Remember: Auto Thresholding is automatically disabled in Calibration SET
Note: TEACH Selection must be programmed to CAL SEt (see Program Mode)

14
2. SET Sensing Condition
Method Action Result
SET Button
• Present sensing condition
• Click the SET Navigation key
Threshold Condition Accepted
Displays read "cAL SEt" then flashes
"PASS"; Sensor returns to Adjust mode
Threshold Condition Unacceptable
Displays read "cAL SEt" then flashes
"FAIL"; Sensor returns to Adjust mode
Remote Input
• Present sensing condition T
•
Single-pulse the remote input
1. Return to RUN Mode.
Method Action Result
SET Button Move Mode switch to RUN
Display: Red - Signal Level;
Green -
Threshold
Remote Input No action required; sensor returns to RUN
mode automatically

15
IO-Link Interface
IO-Link is a point-to-point communication link between a master device and sensor.
It can be used to automatically parameterize sensors and transmit process data.
For the latest IO-Link protocol and specifications, please visit the web site at www.io-link.com.
The IO-Link IODD package is available on the Datalogic Website at www.datalogic.com.
Troubleshooting
Manual Adjustments Disabled
Manual adjustments are disabled when Auto Thresholds are ON. If a manual adjustment is attempted while Auto Thresholds are
ON, the Green display will flash
Percent Minimum Difference after TEACH
The Two-Point and Dynamic TEACH methods will flash a % minimum difference on the displays after a PASS or FAIL.
Value PASS/FAIL Description
0 to 99% FAIL The difference of the taught conditions does not meet the required minimum
100 to 300% PASS The difference of the taught conditions just meets/exceeds the required minimum, minor
sensing variables may affect sensing reliability
300 to 600% PASS The difference of the taught conditions sufficiently exceeds the required minimum, minor
sensing variables will not affect sensing reliability
600% + PASS The difference of the taught conditions greatly exceeds the required minimum, very stable
operation
Percent Offset after SET
The Window, Dark, and Light SET methods will flash a % offset on the displays after a PASS or FAIL.
SET Result % Offset Meaning
PASS (with % Offset) Displays the % offset used for the SET method
FAIL (with % Offset) Displays the minimum required % offset necessary to PASS the SET method
FAIL (without % Offset) Presented condition cannot be used for the SET method
Threshold Alert or Threshold Error
Severe contamination/changes in the taught condition can prevent the Auto Thresholds algorithm from optimizing the threshold(s).
State Display Description Corrective Action
Threshold Alert Alternates
and
The threshold(s) cannot be
optimized, but the sensor's output
will still continue to function
Cleaning/correcting the sensing
environment and/or a re-teach of the
sensor is highly recommended
Threshold Error The threshold(s) cannot be
optimized, and the sensor's output
will stop functioning
Cleaning/correcting the sensing
environment and/or a re-teach of the
sensor is required

16
TECHNICAL DATA
S70-x-E1 S70-x-E2
Sensing Beam:
660 nm visible red 635 nm visible red
Supply Voltage: NPN/PNP models:
10 … 30 VDC Class 2 (10% max ripple)
IO-Link models: 18 … 30 V dc (10% max ripple)
Power and Current Consumption
(exclusive of load):
Standard display mode: 960 mW, Current consumption < 40 mA at 24 VDC
ECO display mode: 720 mW, Current consumption < 30 mA at 24 V
DC
Supply Protection Circuitry: Protected against reverse polarity, overvoltage, and transient voltages
Delay at Power Up:
500 milliseconds max.; outputs do not conduct during this time
Output Configuration:
NPN/PNP models: 1 current sinking (NPN) or 1 current sourcing (PNP) output,
depending on model
IO-Link: 1 push-pull and 1 PNP
(complementary outputs)
-
Output Rating:
100 mA max. load (derate 1 mA per °C above 30 °C)
OFF-state leakage current: NPN/PNP models: < 5 A at 30 VDC;
ON-state saturation voltage: NPN: < 1.5 V; PNP / IO-Link: < 2 V
IO-Link: < 50 A at 30 VDC
-
Output Protection: Protected against output short-circuit, continuous overload, transient
over-voltages,
and false pulse on power up
Output Response Time:
High Speed: 200 μs;
Standard: 500 μs;
Long Range: 2 ms;
Extra Long
Range: 5 ms
Super High Speed: 10 μs
High Speed: 15 μs
Fast: 50 μs
Standard: 250 μs
Medium Range: 500 μs
Long Range: 1000 μs
Repeatability:
High Speed: 66 μs,
Standard/Long Range: 100 μs
Extra Long Range: 100 μs
Super High Speed: 5 μs
High Speed: 5 μs
Fast: 12 μs
Standard: 50 μs
Medium Range: 80 μs
Long Range: 165 μs
Construction:
Black ABS / Polycarbonate alloy (UL94 V-0 rated)
housing, clear
polycarbonate cover
Environmental Rating:
IEC IP50, NEMA 1
Operating Temperature:
10 °C … +55 °C
Storage Temperature:
20 °C… +85 °C
Humidity:
90% at +60 °C maximum relative humidity (non- condensing)
IO-Link Interface:
Supports Smart Sensor Profile:
Yes
Baud Rate: 38,400 bps (COM2)
Process Data Width: 16 bits
IODD files: Provide all programming options of top panel interface,
plus additional functionality
Certifications:
-

OVERALL DIMENSIONS
CABLE VERSION
CONNECTOR VERSION
Dimensions in mm
Datalogic S.r.l.
Via S. Vitalino 13 - 40012 Calderara di Reno - Italy
Tel: [phone] - Fax: [phone] - www.datalogic.com
Datalogic reserves the right to make modifications and improvements without prior notification.
821002592 Rev.C
182859C