Datalogic F-COLOR Single Cradle User manual

F-COLOR Single Cradle
The F-COLOR Single Cradle is a battery charger and also functions as
a serial communication interface between the host computer (RS232)
and the RS232 contacts on the Formula Color™ or Datalogic Skorpio™
mobile computers.
The F-COLOR Single Cradle is available both in desk version and in
vehicle version.
Figure 1 – F-COLOR Single Cradle General View
Key:
A) Battery recharge and RS232 contacts
B) Power indicator LED
C) Connector for host computer connection (RS232)
D) Power supply connector
E) Modem connector (F-COLOR modem cradle only)
By launching the communication software from the mobile computer
and then inserting it into one of the cradle slots, data can be transmitted
to the Host. By inserting the mobile computer into the cradle, the mobile
computer battery charging starts.
Correct Mobile Computer Insertion / Removal
For correct insertion onto the cradle, insert the mobile computer from
the top of the cradle and push it down until the clip of the cradle clicks.
For Datalogic Skorpio™ release the backstrap from the bottom side
before inserting it into the cradle.
Figure 2 - Mobile Computer Insertion
To remove the mobile computer from the F-COLOR cradle, simply pull it
upwards while holding the cradle firmly down.
CONNECTIONS
CAUTION
Connections should always be made with power OFF!
F-COLOR Single Cradle can be connected to a Host by means of an
RS232 interface.
Each connection requires a power supply to be connected to the cradle.
We recommend the DL FPS18 power supply.
GND
VEXT
Figure 3 - Power Supply Polarity
RS232 CONNECTION
The F-COLOR Single Cradle can be connected to the Host by means of
cable 94A054000 for 9-pin connections. The RJ45 connector of the
cable must be connected to the RS232 port of the cradle.
Then, it is necessary to insert the power supply plug into the power jack
on the base of the cradle and attach the power supply to a power outlet.
Once the Host has been turned on, insert the mobile computer into the
cradle.
Figure 4 - RS232 Connection
Key:
A) Host computer
B) 94A054000 9-pin serial cable
C) F-COLOR Single Cradle
D) 94ACC4595 FPS18 power supply without power cord
94ACC1150 Power cord EU 3-pin
Pinout
The cable 94A054000 allowing the RS232 connection has the following
pinout:
1
2
3
Cradle side
RJ45
2
8
5
Host/PC side
9-pin D-sub
(female)
4 7
TX
RTS
GND
CTS
5 3
RX
4
1
Figure 5 - Cable 94A054000 Pinout
822000472 (Rev. C1)
B
A
C
D
E

MODEM CONNECTION
The F-COLOR modem cradle has an integrated modem and provides a
modem connector which can be used with an RJ11 connector. It can be
connected to a telephone line to transfer data to a Host.
Pin Name
1 not connected
2 TIP
3 RING
4 not connected
It is not possible to use the serial connection and the modem connection
at the same time.
CAUTION
By default, the F-COLOR modem cradle allows serial
communication through the rear RS232 connector (it
behaves as a standard cradle unit). It is mandatory to
use an appropriate custom software application in
order to use the cradle integrated modem port.
TECHNICAL FEATURES
F-COLOR Desk Cradle F-COLOR Vehicle Cradle
Electrical Features
Power supply * 9 VDC Min – 30 VDC Max
Consumption 4 W Max
Indicators Power LED
Charge time 8 Hours (Li ION batteries)
Communication Features
Interface RS232
Baud rate 9600 - 115200
Environmental Features
Working
temperature
0° to +50 °C **
Storage temperature -20 °C to +60 °C
Humidity 90% non condensing
Degree of protection IP51
Random Vibration EN60068-2-64 Frequency
Range 5-1000Hz;
acceleration RMS : 3.1g;
initial slope: 26dB/oct 5-
10Hz, final slope:
-3dB/oct 10-1000Hz
Mechanical Features
Dimensions 86 x 106 x 90 mm
Weight 350 g
* Recommended DL power supply: FPS18.
** Batteries must be charged at a temperature ranging from 0° to 45 °C.
F-COLOR Vehicle Cradle
The F-COLOR vehicle cradle comes with its accessories already
assembled. To install it inside a vehicle driving compartment, proceed
as follows:
1. mount the metal bracket;
2. mount the cradle to the bracket;
3. connect a regulated power supply between the vehicle’s battery and
the F-COLOR Single Cradle.
CAUTION
Do not connect the cradle directly to the vehicle's battery.
Possible voltage surges can damage the cradle or cause
it to malfunction.
Power Cable Specifications:
The power supply cable must have the following characteristics:
Min. Current
Capacity 1 A
Male Plug Polarity: positive external
negative internal
Mechanical
dimensions:
external diameter: 5.5 mm
internal diameter: 2.1 mm
Metal plug length: 14 mm
Insert the mobile computer only after mounting the cradle in the vehicle.
To remove the mobile computer from the F-COLOR vehicle cradle, you
must first press the plastic retaining clip as shown in the figure and pull
the mobile computer upwards.
Figure 7 - Removing mobile computer from
F-COLOR Vehicle Cradle
COMPLIANCE
NOTE
To reduce electrical noise, install the included ferrite
onto the cradle side of the power cord. Wind the
power cord three times around the ferrite, as shown
in the figures below.