Datalogic Memor 10 User manual

Memor™ 10
Four Slot Battery Charger
Quick Start Guide
Overview
The Memor 10 four slot battery charger simultaneously charges up
to four spare batteries.
Parts and Functions
Set Up
To prevent the risk of short-circuiting, connect wall power in the
following order:
1. Connect the four slot battery charger to the power supply.
2. Connect the power supply to the power cord.
3. Connect the power cord to the wall outlet. The Power ON LED
illuminates green.
3
3
1
2
1
Charge the Spare Batteries
To charge up to four spare batteries:
1. Insert the spare battery into the slot with the contacts side facing
down and then gently push it into place. Ensure the label side is
facing front. The spare battery charge LED illuminates red.
2. When charging is complete, the spare battery charge LED turns
green. Lift the battery out of the slot.
The spare battery pack recharging slot is compatible with the following
Datalogic p/n: 94ACC0191 BATTERY, MEMOR 10.
The Memor 10 four slot battery charger could get warm during
charging, this is normal and does not mean a malfunction.
NOTE
Annual replacement of rechargeable battery pack avoids
possible risks or abnormalities and ensures maximum
performance.
CAUTION
LED Indicators
LED Status
Power ON
Solid green Charger is powered
Spare Battery Charger
Solid red Spare Battery is charging.
Solid green Charging is complete.
Technical Specifications
Electrical Features
Consumption Max 3 A
Indicators Consumption Power on LED (green)
Spare battery charge LED (bicolored)
Environmental Features
Working Temperature10°C to 40°C
Storage Temperature -30°C to 70°C
Humidity 5-95% non-condensing
Mechanical Features
Dimensions 165.8 x 165.8 x 57.3 mm / 6.5 x 6.5 x 2.25 in
Weight 475 g / 16.75 oz
1. Charging between 15 to 40 degrees is recommended to reach the maximum
charging capability.
Power ON LED
Spare Battery Slots
Spare Battery Charge LEDs
822002810 (Rev. A) Feb. 2019

Battery Safety Guidelines
DInstalling, charging and/or any other action should be done by
authorized personnel and following this manual.
The battery pack may get hot, explode, ignite, and/or cause
serious injury if exposed to abusive conditions.
If the battery pack is replaced with an improper type, there is
risk of explosion.
Do not place the battery pack in or near a fire or heat; do not
place the battery pack in direct sunlight, or use or store the
battery pack inside unventilated areas in hot weather; do not
place the battery pack in microwave ovens, dryer, high pressure
containers, on induction cookware or similar device. Doing so
may cause the battery pack to generate heat, explode or ignite.
Using the battery pack in this manner may also result in a loss
of performance and a shortened life expectancy.
Use only a Datalogic approved power supply. The use of an
alternative power supply will void the product warranty, may
cause product damage and may cause heat, explode or ignite.
The area in which the units are charged should be clear of debris
and combustible materials or chemicals.
Immediately discontinue use of the battery pack if, while using,
charging or storing the battery pack, the battery pack emits an
unusual smell, feels hot, changes colour or shape, or appears
abnormal in any other way.
Do not short-circuit the battery pack contacts connecting the
positive terminal and negative terminal. This might happen, for
example, when you carry a spare battery pack in your pocket
or purse; accidental short–circuiting can occur when a metallic
object such as a coin, clip, or pen causes direct connection of the
contacts of the battery pack (these look like metal strips on the
battery pack). Short–circuiting the terminals may damage the
battery pack or the connecting object.
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer,
step on it or otherwise subject it to strong impacts or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the
battery pack. The battery pack contains
safety and protection devices, which, if damaged, may cause the
battery pack to generate heat, explode or ignite.
In case of leakage of liquid from the battery, avoid contact with
liquid the skin or eyes. If the contact occurs, immediately wash
the affected area with water and consult a doctor.
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the
battery is dropped, especially on a hard surface, you should take
it to the nearest Authorised Repair Centre for inspection before
continuing to use it.
WARNING
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
Collect and recycle waste batteries separately from the device
in comply with European Directive 2013/56/EU, 2011/65/
EU, 2012/79/EU and subsequent modifications, US and China
regulatory and others laws and regulations about environment.
WARNING
FCC Compliance
FCC PART 15 B Statement
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
ISED Statement
Innovation, Science and Economic Development Canada ICES 003
Compliance Label: CAN ICES-3.
Étiquette de conformité à la NMB 003 d’Innovation, Sciences et
Développement économique Canada: CAN ICES 3.
©2019 Datalogic S.p.A. and/or its affiliates • All rights reserved. •
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. Memor is a
trademark of Datalogic S.p.A. and/or its affiliates. All other brand and
product names may be trademarks of their respective owners.