Datalogic MAGELLAN 3510HSi User manual

QUICK REFERENCE GUIDE
MAGELLAN™ 3510HSi
Omni-Directional Imaging Scanner

Datalogic S.r.l.
Via S. Vitalino, 13
40012 Calderara di Reno — Italy
Tel. [phone]
Fax [phone]
©2020 Datalogic S.p.A. and/or its affiliates
All rights reserved. Without limiting the rights under copyright, no part of this documen-
tation may be reproduced, stored in or introduced into a retrieval system, or transmitted
in any form or by any means, or for any purpose, without the express written permission
of Datalogic S.p.A. and/or its affiliates.
Owners of Datalogic products are hereby granted a non-exclusive, revocable license to
reproduce and transmit this documentation for the purchaser's own internal business
purposes. Purchaser shall not remove or alter any proprietary notices, including copyright
notices, contained in this documentation and shall ensure that all notices appear on any
reproductions of the documentation.
Electronic versions of this document may be downloaded from the Datalogic website
(www.datalogic.com). If you visit our website and would like to make comments or sug-
gestions about this or other Datalogic publications, please let us know via the "Contact"
page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is
complete and accurate, however, Datalogic shall not be liable for technical or editorial
errors or omissions contained herein, nor for incidental or consequential damages result-
ing from the use of this material. Datalogic reserves the right to change any specification
at any time without prior notice.
Trademarks
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many
countries, including the U.S.A. and the E.U.
Magellan is a trademark of Datalogic S.p.A. or of Datalogic and/or its affiliates, registered
in many countries, including the U.S. and the E.U.
Patents
See www.patents.datalogic.com for patent list.
This manual refers to software version DR9401453.
ORIGINAL VERSION
See the Regulatory Addendum included with your product
for additional regulatory, safety and legal information.

QUICK REFERENCE GUIDE III
TABLE OF CONTENTS
Features .......................................................................... 1
Installation ....................................................................... 2
How to Scan ..................................................................... 5
Scanner Button ............................................................................. 5
LED and Beeper Indicators ................................................ 7
Beeper Indicators.......................................................................... 8
Troubleshooting................................................................ 9
Error Codes.................................................................... 10
Programming ................................................................. 10
Interface Selection ...................................................................... 11
Cell Phone Mode ....................................................................12
Cell Mode Percent ..................................................................13
Cleaning......................................................................... 14
Manufacturer Approved Cleaning Materials.............................. 15
Warranty ........................................................................ 16
Going Green ................................................................... 17
Bar Code Mask ............................................................... 18

iv MAGELLAN™ 3510HSI
NOTES

QUICK REFERENCE GUIDE 1
MAGELLAN™ 3510HSI
Use this guide to quickly complete installation of the Magellan 3510HSi
series of bar code readers, and begin using your scanner. For more
details and programming information, reference the Product Reference
Guide (PRG), which is available for viewing and download from the
Datalogic website listed on the back cover of this manual.
FEATURES
Figure 1. Scanner Features - Top View
Top Cover
Scan
Connector Ports
Window
Speaker Grille
Cover Removal
Scanner
Lift Handles
Indentation
USB Micro B/
MicroSD Card
Button
(shown in Figure 2)
Regulatory/
Serial Number Label
(Service Access)

Installation
2 MAGELLAN™ 3510HSI
Figure 2. Connectors
INSTALLATION
Connect the scanner to the host (terminal) using the interface (I/F) cable
as shown in the following figures. A cable from an older existing
installation can be re-used only for RS-232 interfaces. If external power
is used/needed, plug the AC Adapter into the AC wall outlet, then
connect it to the unit as shown in Figure 4. If the scanner is powered
only by the standard USB cable as shown in Figure 5 on page 4, an
auxiliary scanner will not be supported.
After the scanner has fully powered up and indicates that it is ready for
operation, scan some known-good bar code samples to verify correct
operation. The scanner should beep and/or flash its good read LED1and
send the bar code data to the host or terminal. If not, use the
Troubleshooting section of this guide to identify any problems.
1. Beeper and LED behavior may have previously been configured as “disabled”
by another user.
POWER
USB
HOST
USB Aux Port
Host Port Power

Installation
QUICK REFERENCE GUIDE 3
Figure 3. USB + Power Cable Power Off the Terminal
Figure 4. Powered by AC Adapter
Terminal (PC)
RJ Host Port
Connector
Power
USB + Power Cable
Power Off the Terminal (POT)
U
S
B
R
S
-
2
3
2
RS-232 and USB Cables
Powered by AC Adapter
To Terminal (PC)

Installation
4 MAGELLAN™ 3510HSI
Figure 5. USB Cable Type A Power Off the Terminal
NOTE: This cable (or similar) will not support a USB
peripheral. The system must be powered by 12V in order for
a peripheral to be attached to the AUX USB PORT.
U
S
B
To Terminal (PC)
USB Type A Power Off the
Terminal

How to Scan
QUICK REFERENCE GUIDE 5
HOW TO SCAN
The scanner is mounted flush with the counter to allow items to be slid
or pushed over its top in the direction of the arrow as shown in Figure 6.
Face the bar code toward the scanner or direction of scan to optimize
the scan rate.
Figure 6. Scanning Items
Scanner Button
The Scanner Button performs multiple functions, depending on how
long it is pressed:
NOTE: Volume changes made using the Scanner Button are
lost when the scanner is powered down and are reset to the
configured setting. If you wish to permanently change the
volume, use the programming labels in the Product
Reference Guide.
Product
Bar Code
LED Indicator
Slide or push items in the
direction of the arrow

How to Scan
6 MAGELLAN™ 3510HSI
PRESS
DURATION FUNCTION COMMENT
Momentary (when
scanner is asleep)
Wakes scanner from
Sleep Mode
Alternatively, the scanner can
be awakened by:
- Moving an object through the
scan zone.
- Scanning with an attached
auxiliary scanner.
Momentary (when
scanner is awake) Increments volume
Press the button momentarily
to increase speaker volume.
When the loudest volume is
reached, a repeated press of the
button cycles volume back to
the lowest setting, then volume
increases on subsequent
press(es). Five volume levels
are available.
Hold, then release
when the beeper
sounds
Increments tone
Press the button for
approximately 2 seconds, then
release. Each time this is done,
the beeper will sound at one of
three tones. Stop when the
desired tone (high, medium or
low) is sounded.
4 Seconds Scanner Diagnostics
Modea
This mode allows system
support personnel to
troubleshoot problems with the
scanner and is used to
determine if it can read bar
codes. Press the button for 10
seconds or cycle power to exit
Scanner Diagnostics Mode and
reset the scanner.
10 Seconds Resets ScannerbOnly system support personnel
should perform a reset.
a. By standard default, this function is normally disabled to prevent accidental
activation by users.
b. Users should not perform scanner resets except under the direction of
trained systems support personnel.