dB Technologies VIO L210 Manual

www.dbtechnologies.com [e-mail]
VIO L210 Rev 1.0 cod. 420120248
Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO”
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAM GGIA B L GNA (ITALIA)
Tel [phone] Fax [phone] www.dbtechnologies.com [e-mail]

www.dbtechnologies.com [e-mail]
VIO L210 2 Rev 1.0 cod. 420120248
Thank you for choosing a dBTechnologies Product!
VI L210 is the new dBTechnologies flagship 2-way professional active line array module. It is equipped with: one
1.4” neodymium compression driver exit (3” titanium voice coil) and two 10” neodymium woofers (2.5” voice coil).
The full-range acoustical design includes an efficient waveguide and a phase plug with phase correctors, in order to
reach the best coherence in line-array configuration. The mechanical design allows an easy, accurate and quick
installation in flown or stack use. The powerful DIGIPR ® G3 amplifier section, capable of handling up to 900 W
(RMS power), is controlled by a DSP, which can perform a detailed customization of the output sound of the speaker.
In particular, thanks to the new dual rotary encoder interface, it is possible to accurately tune the line-array
configuration coverage, using the FIR filter technology. In addition, the integrated RDNET connections are useful for
a remote in-depth line-array control and configuration.
Check the site www.dbtechnologies.com for the complete user manual!
1) Unpacking
The box contains:
N°1 VI L210
N°1 100-120 V FUSE
This quick start and warranty documentation
2) Easy installation
VI L210 can be installed in different configurations.
For a quick installation, in each side of the
loudspeakers the user can find:
Central and rear handles for easy handling (A)
- Two quick-release pin connections for frontal
mounting (B), with upper integrated front arms.
In the rear side the user can find:
- ne swing rear bracket (C) for line-array mounting,
with splay angles reference holes for easy setup and
two quick-release pins.
In order to mount the line array, for each module:
- Remove the upper front pins and lift the front arms
in the final position as shown.
- Fasten the arms with the pins in the lower holes.
- Put a second VI L210 and remove the lower
frontal pins.
- Put this second enclosure on the top of the first.
- Insert the front arms in the position shown, aligning
the related holes.

www.dbtechnologies.com [e-mail]
VIO L210 3 Rev 1.0 cod. 420120248
- Fasten the two enclosures using the quick-release
pins of the upper VI L210.
- Check that all the pins are properly inserted and
locked before other mounting steps.
- Remove the rear pins and put the swing rear
bracket in the final position as shown.
CHECK PERIODICALLY THE INTEGRITY AND THE
FUNCTIONALITY OF THE ENCLOSURE, OF THE
PINS AND OF THE BRACKETS, FOR A SAFE
INSTALLATION. MAKE SURE THAT THE PINS SECURE
PROPERLY THE MODULES AND THAT THEY ARE FULLY
LOCKED.
- Insert the swing rear bracket of the
upper enclosure into the related
housing of the lower one.
- Choose the desired splay angle
between the two enclosures.
- If you need a flown
installation, only one
pin is required to
secure the rear
bracket. Fasten one of
the two rear pins in
the desired angle with
the rear bracket
inserted in, and let the
second one in the
position “PIN
H LDER”.
- If you need a stacked
installation, it is
mandatory to use both
the pins to secure the
rear bracket. Fasten
one of the two pins in
the desired angle,
with the rear bracket
inserted in. Lift the
rear of the upper
enclosure to the
maximum height
allowed by the first
pin, and fasten the second pin in the related “ANGLE
L CK” position. Then release the upper enclosure and
check that the rear bracket leans on the second pin,
fastened in the correct position.

www.dbtechnologies.com [e-mail]
VIO L210 4 Rev 1.0 cod. 420120248
3) Accessories
For an easy setup are available among others: a
professional fly-bar (DRK-210) for flown and stacked
installation, and a trolley (DT-210) for a quick and safe
transport.
a) DRK-210 FLY-BAR
The DRK-210 fly-bar allows different configurations,
flown or stacked, for the professional stage use. It has
2 load adaptors (X, Z) for the use of up to two different
rigging motors, one rear bracket (Y) specifically
designed for the flown installation, and 2 movable
bars [K] for stack mounting. The maximum admitted
number of cabinets in different configurations
depends on various parameters, like VI L210 splay
angles and DRK-210 tilt. The free dBTechnologies
Composer software helps the user in the right choice
for the best mechanical and acoustical result.
As shown in the picture, in flown installation, the use
of the pins and of the rear bracket of DRK-210 make
the assembly with the first element of the line-array
simple and safe.
In stacked installation (for example a line-array stacked
on a S318 sub), the use of the pins, of the rear bracket
of VI -L210, and of the 2 movable bars of DRK-210, as
shown, make the assembling quick and easy.
For further and detailed information please refer to
the related DRK-210 user manual.
b) DT-210 TROLLEY
The DT-210 Trolley can carry up to four VI L210s.
It has been designed for a quick displacement of the
line-array elements. It is provided with wheels and
upper coverage to protect the loudspeakers in a safe
and ergonomic way.
For further and detailed information please refer to
the related DT-210 user manual.
CHECK PERIODICALLY THE INTEGRITY AND
THE FUNCTIONALITY OF THE ACCESSORIES
AND OF THE TECHNICAL EQUIPMENTS FOR A
SAFE INSTALLATION. USER SHOULD NEVER APPLY A
LOAD THAT EXCEEDS THE WORKING LOAD LIMITS OF
ANY RIGGING COMPONENTS OR EQUIPMENT HERE
PRESENTED. DESIGN, CALCULATION, INSTALLATION,
TESTING AND MAINTAINANCE OF SUSPENSION AND
STACK SYSTEMS FOR AUDIO EQUIPMENT MUST BE
PERFORMED ONLY BY QUALIFIED AND AUTHORIZED
PERSONNEL. AEB INDUSTRIALE S.R.L. DENIES ANY
AND ALL RESPONSIBILITY FOR IMPROPER
INSTALLATIONS, IN THE ABSENCE OF SAFETY
REQUIREMENTS.

www.dbtechnologies.com [e-mail]
VIO L210 5 Rev 1.0 cod. 420120248
4) First switch on for line array setup
The DIGIPR G3® amplifier of VI L210 is controlled
by a powerful DSP. All the connections and controls
are in the rear amplifier control panel:
1 – Balanced audio input and output link
2 – RDNet Data In / Data out
3 – Control LEDs (Link, Active, Remote preset Active)
4 – Mini B-type USB port for firmware updating
5 – DSP PRESET rotary switches (Speaker
coupling/High frequency compensation)
6 – Audio Attenuation rotary switch
7 – Status LEDs (Limiter, Signal, Mute/Protection,
Ready)
8 – Mains fuse
9 – Auto-range Mains Input
10 – Mains link output
WARNING
The fuse is factory set for 220-240 V operation.
If it is necessary to change the fuse to 100-120 V range:
1. Disconnect the speaker from any cab e
2. Wait 5 minutes
3. Substitute the fuse with the correct one supp ied
a) nce you have properly set up the mechanical
line-array configuration (see also the VI L210
complete user manual and accessories instructions for
further information), connect the audio input (1) of the
first module of the array. Then connect the useful link
audio output (1) to other VI L210 modules, for the
connection of all the line-array elements. Set the Audio
Attenuation (6) of the loudspeakers to 0 dB.
b) Check the rear panel
reference label for a proper DSP
regulation in line array. Please
note that this kind of
configuration can be set and
modified also by the use of
remote controller (RDNet
Control 2 or RDNet Control 8)
and software (dBTechnologies
Network). For this information
see the chapter (5).
In this rear label (“QUICK
C NFIGURATI NS”) you can
find the suggested position of
rotary switches (5) for each type
of installation (Speakers
Coupling positions and High
Frequency Compensation).
These settings are the main
acoustic corrections to create
the best coupling between the
elements of your line-array, in
order to obtain the best
coverage conditions.
In particular, the “SPEAKER
C UPLING” rotary acts mainly
on low frequencies, and it can be
set in 6 positions, depending on
the number of elements of line-array.

www.dbtechnologies.com [e-mail]
VIO L210 6 Rev 1.0 cod. 420120248
A seventh “Bass boost” position assign particular
emphasis on the lower frequencies, while the “service”
one allow USB port communication for firmware
updating. The “HIGH FREQUENCY C MPENSATI N”
can act on medium-high frequencies. The user can
choose a “FLAT” position (which give a flat
equalization in this frequencies band), and other 7
positions, depending on the distance between the line-
array and the audience (in meters and feet).
c) Connect the power link output (10) of the first
module to the mains input (9) of a second VI L210
module of the line-array, and so on, in order to link the
power supply between all the elements. The
maximum linkable rated power and current depends
on the first module connection (type of cable, type of
connector used). The plate data give information
about the entire linked line-array system. The
maximum number of linkable modules is 10 VI L210s
at 220-240 V, and 7 VI L210s at 100-120 V.
d) In case of remote control, connect the proper
Data Input (2) of the first module of the line-array to
the hardware remote controller (RDNet Control 2 or
RDNet Control 8) with cables equipped with etherC N
connectors. Then connect the Data utput (2) of the
first module to the Data Input (2) of the second one,
and so on. When the RDNet network is on and it has
recognized the connected device, the LED “Link” (3) is
on. The other LEDs (3) “Active” start blinking when
there is the presence of data transmission, the
“Remote Preset Active” advise that all the local
controls set on the amplifier panel (level, DSP presets,
etc.) are by-passed and controlled remotely by RDNet.
See also RDNet Control 2 and RDNet Control 8 user
manuals for further information.
e) Connect the power supply (9) to the first
module. The related “Ready” LED (7) turns on,
signaling the proper power connection. The “Signal”
LED (7) start blinking at the presence of audio signal
(greater than -20dBu). Avoid audio distortion
conditions, potentially signaled by the “Limiter” LED
(7).
5) Software (dBTechnologies Network and
dBTechnologies Composer)
VI L210 can be fully remote controlled via RDNet.
The connection details have been illustrated in the
chapter 4 (“d” point). In remote control mode, the use
of free professional software, developed by
dBTechnologies, allows a complete system
management: dBTechnologies Network and
dBTechnologies Composer.
a) dBTechnologies Network
The software which must be used in case of remote
control is dBTechnologies Network. This software can
control different speakers in different configurations.
It allows a complete remote control and a full real-time
monitoring in various scenarios. For example, the user
can control a setup with 2 line-arrays of VI L210 and
3 VI S318 subwoofers, and change different
parameters while the entire system is sounding.
It can also offer a deeper loudspeaker control than the
simple rear amplifier panel rotaries.
It can be downloaded for free from the official site:
www.dbtechnologies.com/EN/Downloads.aspx
Check always for software updates!
IN FLOWN CONFIGURATION, IT IS ADVISABLE TO
START ALL THE CONNECTIONS FROM THE TOP
(“FIRST ELEMENT”) OF THE LINE ARRAY, TO
OBTAIN THE BEST CABLES MANAGEMENT, IN
ACCORDANCE WITH THE FOLLOWING SCREENS OF
“DBTECHNOLOGIES NETWORK” SOFTWARE.

www.dbtechnologies.com [e-mail]
VIO L210 7 Rev 1.0 cod. 420120248
Those VI L210 parameters can be controlled by
using dBTechnologies Network:
-MUTE/S L switch*
-INPUT ATTENUATI N
-SPEAKERS C UPLING
-HIGH FREQUENCY C MPENSATI N
-HPF FILTER PRESET*
-DELAY*
The * parameters can be controlled only via
software.
b) dBTechnologies Composer
The software dBTechnologies Composer is useful for
complete sound systems design. It has been
developed to optimize complex acoustical settings
like line-array alignment and to calculate easily all
parameters needed in professional sound system
scenarios.
It is used to predict completely the acoustical
behaviour of professional dBTechnologies products
in an immediate way.
In particular, it can simulate different parameters,
for example: mechanical safety in fly-bar use, SPL
levels in outdoor environment, system coverage,
system delays. The user-friendly graphic interface
helps the user to easily understand in-depth
settings.
It can be downloaded for free from the official site:
www.dbtechnologies.com/EN/Downloads.aspx
Check the site www.dbtechnologies.com for the
complete user manual!

www.dbtechnologies.com [e-mail]
VIO L210 Rev 1.0 cod. 420120248
Technical Data
Speaker Type: 2 way professional active line array
element
Acoustical data
Usable Bandwidth [ 6 dB]: 67 – 20000 Hz
Frequency Response [±3dB]: 78 – 18100 Hz
Max SPL (1 m): 134 136 dB (dependent on
frequency/preset)
HF compression driver: 1.4" Exit, Neodymium
HF voice coil: 3”, Titanium
Waveguide HF: yes
LF: (2x) 10”, Neodymium
LF Voice Coil: 2.5”
LF Phase plug: Aluminum phase corrector
Crossover frequencies: 950 Hz
FIR filters: yes
Horizontal dispersion ([ 6dB] 500 – 18100 Hz): 100°
Vertical dispersion: varies on number of modules and
configurations
Amplifier
Amp Technology: Digipro® G3 Autorange
Amp Class: Class D
RMS Power: 900 W
Peak Power: 1800 W
Cooling: Passive (convection)
Processor
Controller: DSP, 28/56 bit 48 kHz
Limiter: Dual Active Peak, RMS, Thermal
Controls: Audio attenuation, DSP presets
Advanced DSP function: Linear Phase FIR filters
Rotary presets: 2 Rotary BCD 8 positions for line array
configuration (Speaker Coupling, High Frequency
Compensation)
Input / utput
Mains connections: PowerCON ® TRUE1 In / Link
Power consumption: 1.6 A (220 240 V) / 2.8 A (100 120 V)
Maximum number of power linked elements: up to 10
VIO L210 (220 240 V), up to 7 VIO L210 (100 120 V)
Signal Input: (Balanced) 1x XLR IN
Signal Out: (Balanced) 1 x XLR link OUT
RDNET connectors: Data In / Data Out
USB connector: mini USB B type (for SERVICE DATA)
Mechanics
Housing: Wooden box – Black polyurea finished
Grille: CNC machined full metal grille
Rigging points: 3 (Easy Rigging)
Handles: 2 for each side
Width: 720 mm (28.35 in)
Height: 320 mm (12.60 in)
Depth: 520 mm (20.47 in)
Weight: 28.6 kg (63 lbs.)
Download the complete user manual on:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechno ogies reserves the right to make changes or improvements in design or manufacturing without assuming any ob igation to change
or improve products previous y manufactured.
Scan with your QR Reader
App to down oad the
comp ete User Manua