dB Technologies VIO S318 Manual

www.dbtechnologies.com [e-mail]
VIO S318 Rev 1.2 cod. 42 12 244Q
Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO – Sezione 2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO”
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAM GGIA B L GNA (ITALIA)
Tel [phone] Fax [phone] www.dbtechnologies.com [e-mail]

www.dbtechnologies.com [e-mail]
VIO S318 Rev 1.2 cod. 42 12 244Q
Thank you for choosing a dBTechnologies Product!
VI S318 is an active semi-horn loaded subwoofer, designed for professional use, bassreflex, equipped with three
18” woofers (voice coil: 4”).
The triple powerful DIGIPR ® G3 amplifier section, capable of handling up to 2700 W (RMS power), is controlled by
a DSP, which can perform a detailed customization of the output sound of the subwoofer. In particular, thanks to
the complete control interface, it is possible to accurately tune various types of configurations, like cardioid or end-
fire. The RDnet connections allow an in-depth remote control, thanks also to free available software (dBTechnologies
Network and dBTechnologies Composer). Professional accessories (like DRK-210 fly-bar, D -VI S318 dolly) allow an
easy set-up to create professional configurations, completing live installations with VI -L210 line-arrays.
Check the site www.dbtechnologies.com for the complete user manual!
1) Unpacking
The box contains:
N°1 VI S318
N°1 Mains cable with Neutrik® powerC N TRUE1
connector
This quick start and warranty documentation
2) Easy installation
VI S318 is equipped with:
Pick points for quick-release pins. Designed for
DRK-210 fly-bar mounting (K)
4 handles per side, for vertical/horizontal
handling (W)
Rear threaded holes for wheel mounting –
SWK18 optional KIT (X)
Cable tracks to house cables in stacked
installation (Y)
Roping points (Z) to secure the subwoofer
Don’t use handles and
/or roping points to suspend VIO
S318!
These mounting holes, handles, and mechanical
devices are used to install S318 in different
configurations for various stage needs. In particular
some installation examples are shown in the following
pictures, thanks to the compatibility with useful
accessories among others:
a) DO VIOS318
D -VI S318 is a dolly specifically designed for an easy
and safe handling of up to three S318 subwoofers. It is
equipped with 4 brakes, and allows a convenient use
of forklift for heavy handling. In stacked handling of
more than one VI S318 it is necessary the use of straps
to ensure a safe placement.
b) DRK 210
DRK-210 is a fly-bar designed for VI L210 line arrays.
VI S318 is compatible with it, allowing stacked
mounting for different configuration needs.
For further and detailed information please refer to
the related accessories user manual.
For installation of professional audio equipment use
only spe ialist personnel! Make sure that the
installation is positioned in a stable and se ure way in
order to avoid any dangerous onditions for people, animals
and/or obje ts. It is mandatory to follow the safety law and
regulations of the Country in whi h the equipment is installed.
Example 2: DRK-210 for VIOL210-
sta ked onfiguration
Example 1: DO-VIOS318 for
easy and safe stage-handling

www.dbtechnologies.com [e-mail]
VIO S318 Rev 1.2 cod. 42 12 244Q
3) First switch on
The 3 DIGIPR G3 amplifiers of VI S318 are controlled
by a powerful DSP. All the connections and controls are
in the rear amplifier control panel:
1 – Polarity switch
2 – Delay rotary controls
3 – Cardioid preset switch
4 – Status LEDs (Limiter, Signal, Mute/Protection,
Ready)
5 – Subwoofer attenuation rotary control
6 – HPF Xover (balanced) output
7 – Xover rotary control
8 – Link (balanced) connector
9 – Input (balanced) connector
10 – USB Data Service
11 – RDNet status LEDs
12 – RDNet Data ut
13 – RDNet Data In
14 – Mains Link connector
15 – Auto-Range Mains input connector
a) nce you have properly set up the desired
configuration (see also the VI S318 complete user
manual and accessories instructions for further
information), connect the audio input (9). Set the
Subwoofer attenuation (5) to the desired level.
b) Connect the possible output direct link (8), and/or
HPF Xover output (6). Set the Xover rotary control (7)
to the correct frequency. This filter acts on internal
transducers and on HPF Xover output (6), It does not
affect the link (8) output.
c) Choose the Subwoofer Setup (Polarity and Delay 1,
2) to obtain the correct behavior. In cardioid
configuration, please note that the cardioid preset
switch (3), when active, bypass Polarity and Delay
controls.
d) In case of remote control, connect the Data Input
(13) to the hardware remote controller (RDNet Control
2 or RDNet Control 8) with cables equipped with
etherC N connectors. Then connect the Data utput
(12) to the Data Input (13) of a possible second device,
and so on. When the RDNet network is on and it has
recognized the connected device, the LED “Link” (11) is
on. The other LEDs (11) “Active” start blinking at the
presence of data transmission, the “Remote Preset
Active” advise that all the local controls set on the
amplifier panel (level, DSP presets, etc.) are by-passed
and controlled remotely by RDNet.
In remote control it is essential the use of free
dBTechnologies software:
•dBTechnologies Network,
useful for an in-depth control of different devices in
remote connection;
•dBTechnologies Composer,
useful for the complete sound system design for
various professional needs, particularly developed for
VI series.
e) Connect the power supply (15). It is possible to link
up to 4 VI S318 at 220V-240V, or 3 VI S318 at 100-
120V with the related mains link connector (14).
In onfigurations with more than one VIO S318, please pay
attention to inrush urrent.
For further information, download the complete user
manual and the free software:
www.dbtechnologies.com/EN/Downloads.aspx
or scan the QR code.

www.dbtechnologies.com [e-mail]
VIO S318 Rev 1.2 cod. 42 12 244Q
Technical Data
Speaker Type: Active professional subwoofer
Acoustical data
Frequency Response [ 6 dB]: 39 Hz – Cut frequency
(crossover - dependent)
Frequency Response [ 10 dB (HPF)]: 35 Hz
Max SPL (1 m): 143 dB
LF: 3 x 18”
LF Voice Coil: 4”
Crossover freq.: 70 to 105 Hz (step 5 Hz) + fullrange
Directivity: (omnidirectional) Cardioid with SP
Amplifier
Amp Technology: 3x Digipro® G3 independent
management
Power supply: Autorange
Amp Class: Class D
RMS Power: (3x) 900 W
Peak Power: (3x) 1800 W
Cooling: Passive (convection)
Processor
Controller: DSP, 32/64 bit 96 kHz
Limiter: Peak, RMS, Thermal
Controls: Rotary Delay Control (0 9.9 ms, steps: 0.1 ms)
and switches (Outputs Mode, Phase, Xover), Subwoofer
level
Input
Mains connections: PowerCON ® TRUE1 In/link
Power consumption: 3.4 A (220 240 V) / 5.8 A (100 120 V)
Maximum number of power linked elements: up to 4
VIO S318 (220 240 V), up to 3 VIO S318 (100 120 V)
Signal Input: (Balanced) 1x IN (female)
Signal Out: (Balanced) Link & Xover OUT (male)
RDNET connectors: Data In / Data Out
USB connector: mini USB B type (for SERVICE DATA)
Mechanics
Housing: Wooden box/black polyurea finish
Grille: Full metal (CNC machining)
Handles: 4 per side
Roping points: integrated, 2 x side
Pick points (stack mode): yes (on top for DRK210)
Width: 1300 mm (51.18 in)
Height: 520 mm (20.47 in)
Depth: 800 mm (31.50 in)
Weight: 103.9 kg (229.06 lbs.)
Download the complete user manual on:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E5 Electromagnetic environments.
FCC CLASS A STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
peration of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
Scan with your R Reader
App to download the
complete User Manual