De Agostini MODEL SPACE FAST & FURIOUS DODGE CHARGER R/T User manual

1212
packpack

Pack 12
Stage 46
The electronic control unit
Stage 47
Connecting the wires and
testing the lights
Stage 48
Attaching the wires to the
chassis
Stage 49
Installing the gear lever
Stage 50
Assembling the fire
extinguisher
Editorial by: Milanoedit srl, milanoedit.com
Translation by: TperTradurre
Picture credits: NBCUniversal Archive
© 2019 Universal City Studios LLC.
Fast & Furious and all related marks and characters are trademarks
and copyrights of Universal Studios.
All Rights Reserved.
Dodge, HEMI and related logos, vehicle model names and trade
dress are trademarks of FCA US LLC and used under license by
Premium and Collectibles Trading Co. Ltd. ©2019 FCA US LLC.
© 2019 Editorial Planeta DeAgostini S.A.U.
Todos los derechos reservados.
© 2019 De Agostini Publishing Italia S.p.A.
Tutti i diritti riservati.
Warning: Not suitable for children under the age of 14.
This product is not a toy and is not designed or intended for use
in play.
Items may vary from those shown.

STAGESTAGE
181
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
46A
46D
46B
46C
DM
Publisher Note: the appearance of the parts shown on these pages may differ from that of the pieces included in this pack. This in no way affects the quality or assembly instructions.
PIECES FOR THIS STAGE
In this assembly session you will attach the electronic control unit to your model car. The unit controls the lights
and sound effects.
46A Electronic control unit
46B Wiring and switch for sound effects of horn and engine
46C Wiring and switch for the lights
46D Dashboard lights with wiring
DM Screws 1.7×3x5 mm (x 5)*
* Some of the parts are spares.
ELECTRONIC CONTROL UNIT
THE ELECTRONICTHE ELECTRONIC
CONTROL UNITCONTROL UNIT
4646

182
46A
30A
DM
46C
46B
46A
46D
1F
1G
1H
46.1
Insert the connector on the wiring for the sound
effects 46B into socket 1F of the electronic control
unit 46A; the connector on the wiring for the lights
46C into socket 1G; and the wiring of the dashboard lights 46D into
socket 1H.
46.2
WIth the electronic control unit
46A facing the same way as in the
illustration, put it on the four pins
located on the left side of the middle section of the
chassis 30A. Secure with four type DM screws.
STAGE 46STAGE 46

183
43B
44A
*Batteries not included
44A
45B
46A
1E
1D
46.4
test the sound. Insert three AAA* batteries into
the battery holder and switch on.
46.3
Insert the connector on the wire of the
speaker 45B into socket 1E in the control
unit. Then, connect the wire of the battery
holder to socket 1D.
STAGE 46STAGE 46

184
STAGE 46 FINAL RESULT
You have now attached the electronic
control unit to the chassis, and connected the
first set of wires.
46.5
Press the switch on the wiring for the sound effects 46B once. The speaker 45B
should reproduce the sound of the horn. Press switch 46B again, and you should
hear the sound of the engine. To stop the sound, press the switch again. Use the
switch on the battery holder 44A to turn the system off.
45B
46B
STAGE 46STAGE 46

STAGESTAGE
185
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
Publisher Note: the appearance of the parts shown on these pages may differ from that of the pieces included in this pack. This in no way affects the quality or assembly instructions.
PIECES FOR THIS STAGE
In this assembly session you will connect the wires of the brake light, headlights and rear lights to the control
unit. You will then perform a simple test to check that the lights work properly.
CONNECTING THECONNECTING THE
WIRES AND TESTINGWIRES AND TESTING
THE LIGHTSTHE LIGHTS
47A Wiring and switch for the brake light
47B Wiring for the LED headlights
47C Wiring for the LED rear lights
47D Type A wire grommet (x 3)
47E Type B wire grommet (x 3)
47F Stands for the chassis (x 4)
CM Screws 1.7×3 mm (x 14)*
* Some of the parts are spares.
ELECTRONIC CONTROL UNIT
4747
47A
47B
47C
47D
47E
CM
47F

186
47C
46A
47A
47B
1C
1A1B
44A
STAGE 47STAGE 47
47.2
noW, you are going to check if
the lights work properly. Turn on
the switch on the battery holder
44A.
47.1
ConneCt the connector on the wiring for the brake light 47A to socket 1B in
the electronic control unit 46A; the connector of the wiring for the headlights 47B
to socket 1A, and that of the rear lights 47C to socket 1C.

187
47C
47B
46D
46C
47B
47A
STAGE 47STAGE 47
47.3
Press the switch on the wiring 46C to turn on the rear lights 47C, the
headlights 47B, and the dashboard lights 46D.
47.4
Press the switch on the wiring
for the brake light 47A to increase
the intensity of the rear lights 47C
(or to switch them on if the switch on the lights 46C is
turned off).

188
STAGE 47STAGE 47
STAGE 47 FINAL RESULT
You have now finished wiring the
lights of your model car, and have
checked that they work.
47.5
onCe you have finished testing the model car’s
electronic functions, turn off the switch on the battery
holder 44A and remove the battery holder cover 43B
and the three AAA batteries.
43B
44A
A USEFUL TIP
At the end of this session, put
the chassis on the supplied
stands to prevent the tyres from
deforming.

STAGESTAGE
189
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
48A
48B
Publisher Note: the appearance of the parts shown on these pages may differ from that of the pieces included in this pack. This in no way affects the quality or assembly instructions.
PIECES FOR THIS STAGE
In this assembly session you will attach the wires to the chassis. You will also attach four hooks to the floor pan.
Follow our instructions carefully, using the illustrations to help you.
ATTACHING THEATTACHING THE
WIRES TO THE CHASSISWIRES TO THE CHASSIS
48A Floor pan
48B Hooks (x 4)
* Some of the parts are spares.
FLOOR PAN
4848

190
31A
47D
30A
47D
47D
CM
CM
CM
30A
31A
47C
44A
47C
48.1
Pass the wire for the rear lights 47C between the three pairs of linchpins located on the middle
and rear sections of the chassis (30A and 31A). Also, insert the wire for the battery holder 44A
between the first two pairs of linchpins, those on the middle section of the chassis.
48.2
Get the wire grommets and
screws that came with session
47. Slide the three type A wire
grommets 47D onto the pairs of linchpins on the
middle and rear sections of the chassis (30A and
31A). Secure each wire grommet with two type CM
screws.
STAGE 48STAGE 48

191
21A
47E
47E
47E
CM CM
CM
21A
47A
46B
46C
46D
47B
48.4
toattaCh this group of wires
to the chassis, slide the three type
B wire grommets 47E onto the
pairs of linchpins on the front platform 21A. Secure each
wire grommet with two type CM screws.
48.3
GrouP together the following wires between
the pairs of linchpins on the front platform 21A:
those of the switch for the horn and engine sound
effects 46B; those of the front headlights 47B; those of the brake light
switch 47A; those of the lights 46C; and, finally, those of the dashboard
lights 46D.
STAGE 48STAGE 48

192
48B
48A
STAGE 48 FINAL RESULT
48A
48B
You have now
attached the wiring
for the electrical
system to the chassis,
and the four hooks to
the floor pan.
48.5
Insert two of the hooks 48B into
the two holes on the floor pan 48A,
next to the central tunnel.
48.6
Insert the remaining
two hooks 48B into the
holes on the other side of
the tunnel.
STAGE 48STAGE 48

STAGESTAGE
193
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
49A 49B
49E
49C 49D
AP
Publisher Note: the appearance of the parts shown on these pages may differ from that of the pieces included in this pack. This in no way affects the quality or assembly instructions.
PIECES FOR THIS STAGE
In this assembly session you will connect the wires of the brake light, headlights, and rear lights to the electronic
control unit. You will then perform a simple test to check that the lights work properly.
INSTALLING THEINSTALLING THE
GEAR LEVERGEAR LEVER
49A Gear lever
49B Gear knob
49C Shift rail
49D Centre console
49E Middle section of the transmission tunnel
AP Screws 1.7×4 mm (x 8)*
* Some of the parts are spares.
GEAR LEVER
4949

194
49C
49D
AP
49A
49D
49C
49B
STAGE 49STAGE 49
49.1
PlaCe the shift rail 49C on the centre console 49D,
and join the two components together using two type
AP screws.
49.2
Insert the thinner end of the gear lever 49A into
the corresponding housing in the centre console
49D, ensuring that the ball at the opposite end fits
into its housing. Then put the gear knob 49B onto the gear lever.

195
49.4
JoIn the floor pan and the middle section of the transmission
tunnel 49E, by inserting the two tabs into the corresponding slots.
49.3
attaCh the piece you have just assembled to
the middle of the floor pan 48A, ensuring it
faces the same way as in the illustration. Secure
the centre console 49D to the floor pan with two type AP screws.
49D
48A
AP
48A
49E
STAGE 49STAGE 49

196
49.5
turn the floor pan over and attach it to the
middle section of the transmission tunnel 49E using
two type AP screws.
STAGE 49 FINAL RESULT
You have now installed the gear lever
and the middle section of the transmission
tunnel on the floor pan.
48A
49E
AP
AP
STAGE 49STAGE 49

STAGESTAGE
197
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
50A
50D 50E
50B
50C
AP
Publisher Note: the appearance of the parts shown on these pages may differ from that of the pieces included in this pack. This in no way affects the quality or assembly instructions.
PIECES FOR THIS STAGE
In this assembly session you will assemble the fire extinguisher and attach it to the floor pan. Follow our
instructions very carefully, using the illustrations to help you.
ASSEMBLING THEASSEMBLING THE
FIRE EXTINGUISHERFIRE EXTINGUISHER
50A Fire extinguisher stand
50B Fire extinguisher (front)
50C Fire extinguisher (back)
50D Pressure gauge
50E Brackets (x 2)
AP Screws 1.7×4 mm (x 10)*
* Some of the parts are spares.
sERbAtOiO E ALtOPARLANtE FiRE EXtiNGUisHER
5050

198
50D
50B
50B
50C
AP
50.1
JoIn the front and back of the fire
extinguisher 50B and 50C together.
Secure them with two type AP screws.
50.2
Press the pressure gauge 50D into the hole in the
front of the fire extinguisher 50B.
STAGE 50STAGE 50