DeLonghi DCH2570E User manual

instructions
CERAMIC FAN HEATER
DCH2570E
Please retain these instructions for future reference

DCH2570E 2
Base swing button
ON/OFF button (A)
ON light
Adjustable base
Pulse MODE (B)

Thank you for choosing this De’Longhi heater. To get the
very best out of your new heater it is advisable to read
these instructions before using it.This will ensure that you
gain optimum results and use the appliance safely.
Electrical connection
- Before plugging the appliance into the mains, check that your
supply voltage is the same as that shown on the rating plate of
the appliance.
-If using more than one appliance at a time, it is important to
ensure that the ring main is adequate to cope with the power
requirements.
- It is important to ensure that the socket is adequately earthed.
- This appliance complies with EEC directive 89/336 regarding
electromagnetic compatibility.
Installation
The appliance can be used on any horizontal surface.
Do not overload the electrical circuit. Avoid using the same socket
for other appliances.
OPERATION AND USE
1. Make sure the appliance is off before plugging into the mains
2. To turn the appliance on, the switch at the back must be in the
I position.The appliance emits a beep.The “ON” light also comes
on and remains lit while power to the appliance is on.
3. Press button Ato turn the appliance on.
4. The appliance starts up in LOW mode (minimum heat output).
The display shows room temperature.
5. Press the Mode button (B) to switch to HIGH mode (maxi-
mum heat output).The display shows room temperature.
6. Press the Mode button (B) again to switch the appliance to
Auto mode.The display shows both room temperature and the
temperature set point.To change the temperature set point, use
the + and – buttons.
7. Press the Mode button (B) a fourth time to switch the applian-
ce back to LOW mode.When the Mode button is pressed con-
tinuously, the appliance switches through the following modes in
sequence: LOW HIGH AUTO.
8. To turn the appliance off, press button A and place the switch
on the back in the 0position.
DCH2570E
3

Adjusting the thermostat
Press the Mode button (B) until AUTO is displayed.
Use the +and –buttons to increase or reduce the temperature set
point The thermostat will then keep room temperature at the selec-
ted level automatically. When room temperature is 2°C above the
set temperature, the appliance goes off.
When room temperature drops below the set temperature, the
appliance comes on automatically.
Frost prevention mode
You can keep the room at a temperature of about 5°C to prevent
freezing with minimum energy consumption.
Press the Mode button (B) until Auto is displayed.
Press the “_”button to select a temperature set point of 5°C.
When the room temperature drops below the set temperature, the
appliance comes on automatically.
Models with motorised rotating base
A number of models have a motorised rotating base.
To distribute the air flow over a larger area, press the swing switch
The appliance swings from right to left. To stop the appliance in the desi-
red position, simply press the switch again.
MAINTENANCE
Always unplug from the mains socket before cleaning.
During the season when the appliance is in use, clean the air
intake and outlet grilles regularly using a vacuum cleaner.
Never use abrasive powders or solvents.
Cleaning and maintenance
The heater should not required any maintenance. However before
attempting to clean the heater, remove the plug from the power sock-
et and allow the heater to cool. After the heater has cooled, clean it
with a soft damp cloth, do not use detergents or abrasives. Periodically
clean the air intake and outlet grilles during the period in which the
heater is in use with a vacuum cleaner. Should the heater not be in use
for a length of time, store it in a dry place.This appliance has been built
to provide many years of trouble free service.
In case of malfunction, do not try to repair the heater yourself: it may
result in fire hazard or electric shock.
Warnings
-Do not use the heater in a bathroom or in the vicinity of bath-
tubs, wash basins, showers or swimming pools.
- Never use the heater to dry laundry.
-Only use the heater in an upright position.
DCH2570E 4

-The heater must be positioned at least 50cm from walls, curtains,
furniture or other objects.
-If the supply cord is damaged, it must be replaced by the manu-
facturer, its service agent or similarly qualified persons in order
to avoid a hazard.
-Do not use this appliance in rooms which have a floor area small-
er than 4m2as this may lead to overheating.
- The heater must never be placed immediately under a fixed mains
socket.
- Never obstruct the heaters intake and outlet grilles as this could
cause dangerous overheating.
- IMPORTANT: Never for any reason cover the appliance during
operation as this could lead to dangerous overheating.
- A safety device intervenes and turns the appliance off and the pilot light
will switch on in the event of overheating. To reactivate the heater,
remove the plug from the mains, allow the appliance to cool (for about
10 minutes), remove the cause of the overheating and then plug the
appliance back into the mains and turn it back on.
- The use of an extension lead is not recommended, however if it is
necessary then follow carefully the extension lead’s instructions,
and most importantly ensure that the extension lead is carefully
rated in accordance with the radiator being used and NEVER
overloaded.
- In order to avoid any danger caused by an accidental resetting of
the safety system, this appliance must not be powered through an
external timer.
- As with any electrical appliance, whilst the instructions aim to
cover as many eventualities as possible, caution and common
sense should be applied when operating your appliance, particu-
larly in the vicinity of young children.
WARNING: In order to avoid overheating, never under
any circumstances cover the appliances during operation, as
this would lead to dangerous overheating.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF
THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE
2002/96/EC.
At the end of its working life, the product must not be dis-
posed of as urban waste. It must be taken to a special local
authority differentiated waste collection centre or to a dea-
ler providing this service. Disposing of a household applian-
ce separately avoids possible negative consequences for the
environment and health deriving from inappropriate dispo-
sal and enables the constituent materials to be recovered to
obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances
separately, the product is marked with a crossed-out
wheeled dustbin.
DCH2570E
5

DCH2570E 6
Electrical requirements
Before using this appliance ensure that the voltage indicated
on the product corresponds with the main voltage in your
home, if you are in any doubt about your supply contact your
local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug
having a fuse of 13 amp capacity. Should this plug not fit the socket out-
lets in your home, it should be cut off and replaced with a suitable plug,
following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should
therefore be properly disposed of and not left where children might find
it and plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that
can be switched off when the machine is not in use.
important: the wires in the mains lead fitted to this appliance are
coloured in accordance with the following code:
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
The wire which is coloured green and yellow must be connected to the
terminal in the plug which is marked with the letter E or by the earth
symbol or coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely
retained in each terminal. Do not forget to tighten the mains lead clamp
on the plug. If your electricity supply point has only two pin socket out-
lets, or if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this
operation be carried out by a qualified electrician and should only be
replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted.
If the fuse cover is lost, the plug must not be used until a replacement
cover is obtained. The colour of the correct replacement fuse cover is
that of the coloured insert in the base of the fuse recess or elsewhere
on the plug. Always state this colour when ordering a replacement fuse
cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362
should be fitted.
This appliance conforms to the Norms EN 55014 regarding the sup-
pression of radio interference.
GREEN ANDYELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
Green and Yellow to Earth
Blue to
Neutral
13 amp
Fuse
Brown
to Live
Cord Clamp
Warning - this appliance
must be earthed

515IDL/04.06