Delta EnviroStation EMS2000 User manual

www.deltapowersolutions.com
Delta InfraSuite EMS
User Manual
The power behind competitiveness
Environmental Management System
EnviroStation

InfraSuite EnviroStation I
Save This Manual
Copyright © 2013 by Delta Electronics Inc. All Rights Reserved. All rights of this User
Manual (“Manual”), including but not limited to the contents, information, and figures
are solely owned and reserved by Delta Electronics Inc. (“Delta”). The Manual can
only be applied to the operation or the use of this product. Any disposition,
duplication, dissemination, reproduction, modification, translation, extraction, or
usage of this Manual in whole or in part is prohibited without the prior written
permission of Delta. Given that Delta will continuously improve and develop the
product, changes may be made to the information in this Manual at any time without
obligation to notify any person of such revision or changes. Delta will make all
possible efforts to secure the accuracy and the integrity of this Manual. Delta
disclaims any kinds or forms of warranty, guarantee, or undertaking, either expressly
or implicitly, including but not limited to the completeness, faultlessness, accuracy,
non-infringement, merchantability or fitness for a particular purpose of the Manual.
This manual contains important instructions and warnings that you should follow
during the installation, operation, storage and maintenance of this product.
Failure to heed these instructions and warnings will void the warranty.

Table of Contents
II
Table of Contents
CHAPTER1:IMPORTANTSAFETYINSTRUCTIONS .............................................. 1
1.1. SAFETYWARNINGS ...................................................................................... 1
1.2. USAGEWARNINGS ...................................................................................... 1
1.3. STANDARDCOMPLIANCE...............................................................................2
CHAPTER2:INTRODUCTION............................................................................. 3
2.1. PRODUCTDESCRIPTION ................................................................................ 3
2.2. FEATURES................................................................................................... 3
2.3. PACKAGECONTENTS .................................................................................... 5
2.4. INTERFACE.................................................................................................. 7
CHAPTER3:INSTALLATION ............................................................................. 10
3.1. RACK‐MOUNTINSTALLATION........................................................................10
3.2. RS485....................................................................................................11
3.3. ENVIROPROBE ..........................................................................................12
3.4. DIGITALINPUT ..........................................................................................13
3.5. SENSORHUB ...........................................................................................14
3.6. ANALOGINPUT .........................................................................................16
3.7. RELAYOUTPUT ......................................................................................... 17
3.8. ALARMBEACON........................................................................................ 17
3.9. PDUINSTALLATION....................................................................................18
CHAPTER4:SYSTEMCONFIGURATIONS .......................................................... 20
4.1. CONFIGURINGVIAINSIGHTPOWERSNMPIPV6FORENVIROSTATIONWEB ..........20
4.2. CONFIGURINGWITHEZSETTING ...................................................................22
4.3. CONFIGURINGVIATELNET ...........................................................................24
4.4. CONFIGURINGTHROUGHCOMPORT............................................................24
4.5. CONFIGURINGVIATEXTMODE ....................................................................26
CHAPTER5:INSIGHTPOWERSNMPIPV6FORENVIROSTATIONWEB................ 33

InfraSuite EnviroStation III
5.1 MONITOR....................................................................................................34
5.1.1. Information .......................................................................................34
Status ............................................................................................................34
DeltaBus .......................................................................................................35
RS485 ............................................................................................................35
PDU ...............................................................................................................36
IPMI...............................................................................................................36
5.1.2. History............................................................................................... 37
EventLog.......................................................................................................37
EnergyLog.....................................................................................................38
EnergyCompare............................................................................................39
DataLog ........................................................................................................39
Configuration ................................................................................................40
5.1.3. About ................................................................................................41
Information ...................................................................................................41
5.2 DEVICE........................................................................................................42
5.2.1. Management ....................................................................................42
SensorHUB ...................................................................................................42
DigitalInput...................................................................................................43
AnalogInput..................................................................................................44
RelayOutput .................................................................................................45
DeltaBus .......................................................................................................45
RS485 ............................................................................................................48
Protocol.........................................................................................................49
PDU ...............................................................................................................50
IPMIDevice ...................................................................................................50
IPMITemplate ...............................................................................................52
Reaction ........................................................................................................54

Table of Contents
IV
5.3 SYSTEM.......................................................................................................55
5.3.1. Administration................................................................................... 55
UserManager ...............................................................................................55
TCP/IP ...........................................................................................................56
Web...............................................................................................................57
Console .........................................................................................................59
FTP ................................................................................................................60
TimeServer...................................................................................................60
Syslog ............................................................................................................61
BatchConfiguration ......................................................................................62
Upgrade.........................................................................................................63
5.3.2. Notification .......................................................................................64
SNMPAccess.................................................................................................64
SNMPv3USM ................................................................................................65
SNMPTrap.....................................................................................................65
MailServer....................................................................................................66
CHAPTER6:SNMPDEVICEFIRMWAREUPGRADE............................................ 68
CHAPTER7:TROUBLESHOOTING .................................................................... 71
APPENDIXA:SPECIFICATIONS......................................................................... 78
APPENDIXB:WARRANTY ............................................................................... 79

InfraSuite EnviroStation 1
Chapter 1 : Important Safety Instructions
1.1. Safety Warnings
Before installation,
Ensure that the power cord plug and socket are in good condition.
Make sure that the power source to the EnviroStation is rated between 100-240V
and is well grounded.
1.2. Usage Warnings
This unit is designed for indoor use only. Install it in a well-controlled environment
away from excessive moisture, temperature extremes, conductive contaminants,
dust or direct sunlight.
Do not place or use this unit in the presence of flammable substances.
Do not attempt to disassemble the unit which contains potentially hazardous
voltages. Only trained technicians are allowed to perform this action.
Do not attempt to perform any internal modifications on the unit.
Do not attempt to fix/ replace internal components. When repair is needed, refer
all servicing to the nearest Delta service center or authorized distributor.
Do not allow any objects or liquids of any kind to penetrate the unit.
Always follow this User Manual to install and operate this unit.
Disconnect all external devices before moving this unit.
Do not play the included CD-ROM on a conventional CD player. This could
generate loud noise at a level that could result in permanent hearing loss.

Chapter 1 : Important Safety Instructions
2
1.3. Standard Compliance
Network
IPv6 Phase-2
Application ID: TW-2-C-20100323-000158
CE
EMI
EN55022 (CISPR 22) Class A
EMS
EN55024
IEC 61000-4-2 (ESD Test)
IEC 61000-4-3 (RS Test)
IEC 61000-4-4 (EFT Test)
IEC 61000-4-6 (CS Test)
IEC 61000-4-5 (Surge Test)
Level 3 @ Air 8 KV/ Contact 4 KV
Level 2 @ 3 V/m
Level 2 @ 5 KHz/ 1KV
Level 2 @ 1.2*50/ 8*20 us
L-N 2 ohm 1 KV
L-PE/ N-PE/ L+N-PE 12 ohm 2 KV

InfraSuite EnviroStation 3
Chapter 2 : Introduction
2.1. Product Description
The EnviroStation monitors and controls environmental conditions through
peripheral devices to ensure that your equipment is protected from critical conditions
such as high temperature, humidity or water leakage. This rack-mountable product
works seamlessly with temperature and humidity sensor EnviroProbes (optional)
and other environment monitoring devices.
2.2. Features
Working with multiple EnviroProbes
The EnviroProbes are designed to work with the EnviroStation. There are three
types of EnviroProbes, (1) EnviroProbe 1000 (EMS1000), (2) EnviroProbe 1100
(EMS1100) and (3) EnviroProbe 1200 (EMS1200). The EnviroProbe (EMS1000)
has one temperature/ humidity sensor and four digital inputs. The EnviroProbe
1100 (EMS1100) has four digital outputs, and the EnviroProbe 1200 (EMS1200)
has two analog inputs, one analog output and one water-leakage detection. To
extend the monitoring and detection scope, up to 10 of EMS1000s or 4 of
EMS1100s or 5 of EMS1200s can be cascaded with a maximum distance of 400
meters.
Smart monitoring and event notification
With peripheral devices, the EnviroStation monitors environment variables and
informs you of event occurrences based on severity that may call for your
administrative attention. It also takes necessary actions according to your
configuration.
Event and data log keeping
Offers extensive records of system and environment status.
Handy configuration tool EzSetting
Compatible with Windows systems, EzSetting allows you quick and effortless
setup via a user-friendly interface.

Chapter 2 : Introduction
4
Network connection through RJ45 connector
Direct network connection through an RJ45 cable offers immediate configuration
via your local network environment with comprehensive management
capabilities networking security.
Compatibility with SNMP (Simple Network Management Protocol), HTTP
and HTTPS
Works with universal protocols including SNMP, HTTP and HTTPS.
Direct COM Port connection
Lets you manage your EnviroStation even when a network connection is not
available.
Working with up to 16 PDU devices
EnviroStation monitors each PDU’s load, frequency, watt, accumulated power
consumption, etc.
IPMI supported
Supports IPMI version 1.5 & version 2.0.
Flexible reaction setup
You can create your own reaction rules. Based on the input conditions of Digital
Input, Analog Input, Sensor HUB, PDU, EnviroProbe or RS485, the
EnviroStation controls the actions of output devices such as Digital Output,
EnviroProbe or RS485.
Other features and supported protocols include:
User notification via SNMP Traps
Simple Network Time Protocol
Simple Mail Transfer Protocol
Remote event log management through syslog
Network Time Protocol
Configuration via Telnet/ text mode
BOOTP/ DHCP
IPv4 and IPv6
HTTPS, SSH, SFTP and SNMPv3 security protocols
RADIUS (Remote Authentication Dial In User Service) login

InfraSuite EnviroStation 5
Signal Flow
The following figure explains how EnviroStation monitors and processes signals.
2.3. Package Contents
Please carefully verify EnviroStation and the included accessories. Contact your
dealer if any item is missing or damaged. Should you return the items for any reason,
ensure that they are carefully repacked using the original packing materials that
came with the unit.

Chapter 2 : Introduction
6
No. Item Quantity
❶EnviroStation 1 PC
❷Manual and software CD 1 PC
Sensor HUB adapter 8 PCS
❸
Terminal block (for Sensor HUB adapter) 8 PCS
❹Alarm Beacon 1 PC
❺Bracket ear (including cage nuts and screws) 1 SET
❻Door contact sensor 1 SET
❼AC power cord 1 PC
❽RJ45 to DB9 cable 1 PC
❾Standard CAT5 cable 1 PC
❿Extension cable (for leakage sensor) 1 PC
You will need the following items:
Peripheral devices such as temperature/ humidity/ water leakage sensors and
EnviroProbes are not included in the package. Also, additional Standard CAT5
cables used to cascade EnviroProbes are not included. You will need to obtain these
items separately.

InfraSuite EnviroStation 7
2.4. Interface
The LED indicators and connectors on the front and rear panel are shown as follows.
For their functions and indications, please refer to the table below.
Front panel:
Rear panel:
No.
Item Description
❶ Power
LED
Indicates whether the unit is connected to a power source.
On (green): Connected.
Off: Not connected.
❷ Fault
LED
Indicates whether an internal fault has occurred.
On (red): Fault occurred.
Off: Normal.
❸ Relay
Output
LEDs
On (green): The Relay Output is switched to NC (Normal
Close).
Off: The Relay Output is switched to NO (Normal Open).
❹ Analog
Input LEDs
On (yellow): The value of the Analog Input is out of the
assigned normal range.
Off: The value of the Analog Input is in the normal range.
❺ Digital Input
LEDs
On (yellow): The Digital Input is activated and defined as
‘Warning’ or ‘Alarm’.

Chapter 2 : Introduction
8
No.
Item Description
Off: The Digital Input is defined as ‘None’ or ‘Information’.
❻ Sensor
HUB
LEDs
On (yellow): The Sensor HUB is activated and defined as
‘Warning’ or ‘Alarm’.
Off: The Sensor HUB is defined as ‘None’ or ‘Information’.
❼ 10/ 100
Base-T
Network
Port
Connects the EnviroStation to the network.
1. When the EnviroStation initializes or upgrades its firmware,
the two LED indicators on the 10/ 100 Base-T network port
flash simultaneously. Please refer to the following for LED
illumination definition.
Rapid simultaneous flashing (every 50ms):
Initialization or firmware upgrade in progress.
Slow simultaneous flashing (every 500ms):
Initialization failure.
W
arning：
Do NOT disconnect the EnviroStation’s input power
during initialization or firmware upgrade! This could
result in data loss or damage to the EnviroStation.
2. The green LED indicator shows the network connection
status:
ON: Network connection established and the IPv4
address is useable.
OFF: Not connected to a network.
Flashes slowly (every 500ms): Faulty IP address.
3. The yellow LED indicator shows the linking status:
Flashes rapidly (every 50ms): Linking normal.
Flashes slowly (every 500ms): Linking abnormal.
❽ Console
Port
Connects to a workstation with an RJ45 to DB9 cable.
❾ Reset
Button
Resets the EnviroStation’s network module. This will not affect
the operation of other connected devices.
❿ Modbus
RS485 port Connects devices to EnviroStation via the Modbus protocol.

InfraSuite EnviroStation 9
No.
Item Description
⓫ Delta-
BUS
Provides power (12Vdc) and connects to EnviroProbe(s) using
a standard CAT5 cable with straight-through wiring.
⓬ Sensor
HUB
Connects and provides power (12/ 24Vdc) to general sensor
devices using standard CAT5 cables with straight-through
wiring.
⓭ Digital Input Four input contact devices can be connected to EnviroStation.
The wet contact active rating is 5~24Vdc,1~9mA.
⓮ Analog
Input
Connects four analog sensor devices, including:
Two 0-10Vdc analog voltage sensors or 0-20mA
current-loop sensors.
1 RTD sensor.
1 leakage sensor.
⓯ Relay
Output
Connects to relay-controlled devices.
⓰ AC Line
Inlet
Provides power to EnviroStation. The range is 100V~240V 60/
50Hz.

Chapter 3 : Installation
10
Chapter 3 : Installation
In this chapter, you will learn the installation procedures for the EnviroStation,
EnviroProbes, Alarm Beacon, and devices connecting via RS485, Sensor HUB,
Digital Inputs, Analog Inputs and Relay Outputs.
3.1. Rack-mount Installation
Step 1 Choose a location in the rack. On the vertical mounting rails, insert the
provided cage nuts.
Step 2 Using two screws, attach two bracket ears provided in the accessory box
to each end of the EnviroStation.
Step 3 Make sure the mounting holes and the bracket ears on the EnviroStation
are aligned properly, then secure the bracket ears to the rack with the four
provided mounting screws (two for each end), EnviroStation occupies 1U
of rack space.

InfraSuite EnviroStation 11
Step 4 Connect the AC power cable from the rear panel to an unoccupied power
outlet. This will automatically power up the EnviroStation.
W
ARNING:
Before connecting the EnviroStation to a power source, make sure that the
power source is rated between 100-240V and is well grounded.
3.2. RS485
EnviroStation provides two RS485 ports for devices that communicate through the
Modbus protocol such as power meters and door contact systems. Using an RS485
port, eight devices with different ID numbers can be cascaded, however, their
communication parameters must be identical (For example: Baud rate: 2400, data
bits: 8, parity: none, stop bits: 1, and flow control: None).

Chapter 3 : Installation
12
3.3. EnviroProbe
Detecting environment temperature and humidity, the EnviroProbes are designed to
work with the EnviroStation. You can cascade multiple EnviroProbes to extend the
detecting range. To install the EnviroProbe(s), please see the following instructions.
Step 1 Set the Comm DIP switch to Station on the EnviroProbe(s).
Step 2 Make sure the last EnviroProbe in the chain (the farthest) is set to Rt-Yes,
and the rest of the EnviroProbes are set to Rt-No. If only one EnviroProbe
is connected, please also make sure that it is set to Rt-Yes.
Step 3 Set the ID DIP switch to assign an ID for each EnviroProbe (please refer to
the EnviroProbe User Manual). No particular numeric order is required for
the connected units; however, make sure that each EnviroProbe is
assigned with a unique ID. Up to ten EnviroProbes can be cascaded.
Step 4 Attach the EnviroProbe(s) to rack cabinet doors or metal plates.
Step 5 Use a standard CAT5 cable to connect the first (nearest) EnviroProbe’s
Input to the Delta-BUS port on the rear panel.
Step 6 Cascade other EnviroProbes using standard CAT5 cables. Connect the
Output port to the next EnviroProbe’s Input port. Please see the figure
below.

InfraSuite EnviroStation 13
W
ARNING:
Under no circumstance should you connect the EnviroProbe’s Input port to
another one’s Input port. This may cause unrecoverable malfunction to your
EnviroProbes. Please be careful and always make sure that you are
connecting the correct ports before you plug in.
3.4. Digital Input
The EnviroStation provides four Digital Inputs. Wet and Dry Contacts can be
connected for applications such as smoke, fire and door security detection. To
connect your peripheral devices, please refer to the following figures for terminal
connections:
Digital Value Dry Contact Wet Contact
1Close 5~24Vdc
0Open < 1.5Vdc

Chapter 3 : Installation
14
Dry Contact : Normal Open [NO] or Normal Close [NC].
Wet Contact: Active rating 5~24Vdc, 1~9mA.
3.5. Sensor HUB
In the accessory box you can find eight provided Sensor HUB adapters (RJ45 to
6-pin terminal connector) which are used to connect peripheral devices for purposes
such as smoke, fire and door contact detection. To connect a Sensor HUB device,
please see the following instructions:

InfraSuite EnviroStation 15
Connect a Sensor HUB adapter to a Sensor HUB port on the rear panel with a
standard CAT5 cable.
On the other side of the adapter, plug a 6-pin terminal block (provided with the
package) into the green terminal connector so wires from peripheral devices can
be tightened and fixed with the screws.
Depending on the contact types and power requirement of the devices you are
connecting, different terminal connections are required. Please see the following
figures:
1) +12Vdc is provided by connecting the
following two terminal points: 12V and G
(12V).
2) +24Vdc is provided by connecting the
following two terminal points: 24V and G
(24V).
3) Connect Dry Contact signal to G (12V) and –
terminal points.
4) Connect Wet Contact signal to + and –
terminal points. The active rating is
5~24Vdc, 1~9mA.
NOTE:
For HUB1/ HUB2, you can manually turn on/ off power or enable automatic
power control. Please see 5.2.1 Management – Sensor HUB.