Delta VFB25ADBT User manual

READ AND SAVE THESE INSTRUCTIONS
Address: 46101 Fremont Boulevard, Fremont, CA 94538
US Toll Free Number: 1-888-979-9889
TABLE OF CONTENTS
Package Contents 2
General Safety Information 3
Preparation and Wiring Diagrams 5
Assembly Instructions - New Construction 6
Assembly Instructions - Existing Construction 7
Grille & Speaker Installation 10
Operation 10
Care and Maintenance 11
Troubleshooting 12
Dimensions 13
13
Warranty 14
MODEL VFB25ADBT
VENTILATION FAN
WITH BLUETOOTH SPEAKER

2
Model: VFB25ADBT
1
6
2
3
4
7
5
PART DESCRIPTION QTY
❶Fan Body 1
❷Grille 1
❸Suspension Bracket I 1
❹Suspension Bracket II 1
❺Suspension Bracket III 1
❻Duct Connector 1
❼Bluetooth Speaker 1
PACKAGE CONTENTS
A
B
HARDWARE CONTENTS
(Images are to scale)
X 8
X 3
Long Wood Screw ( ∅4 x 25mm)
Short Machine Screw (M4 x 12mm)

3Model: VFB25ADBT
READ AND SAVE THESE INSTRUCTIONS
GENERAL SAFETY INFORMATION
1. Make sure that the electric service supply voltage is AC
120V, 60Hz.
2. Follow all local electrical and safety codes, as well as
the National Electrical Code (NEC) and the Occupational
Safety and Health Act (OSH Act).
3. Always disconnect the power source before working on or
near the ventilating fan, motor or junction box.
4. Protect the power cord from sharp edges, oil, grease, hot
surfaces, chemicals or other objects.
5. Do not kink the power cord.
6.
shown in Fig.A.
7. Provide suction parts with proper ventilation.
8. This unit is UL Listed for use over a bathtub or shower
when installed in a GFCI protected branch circuit.
9. These ventilating fans are intended for residential usage
only.
10. This product is designed for ceiling installation only. Do
not mount this product in a wall.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
2. Before servicing or cleaning unit, switch power off
at the service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
4.
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating Refrigeration and Air Conditioning Engineers
(ASHRAE), and local code authorities.
5. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
GENERAL SAFETY INFORMATION
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must
be marked as appropriate for the application and be
connected to a GFCI (Ground Fault Circuit lnterrupter) –
protected branch circuit.
8. Do not use this unit with any other solid-state control
device. Solid-state controls may cause harmonic
distortion, which can cause a motor humming noise.
9. NEVER place a switch where it can be reached from a
tub or shower.
10. Not to be installed in a ceiling thermally insulated to a
value greater than R40. (This is required for installation
in Canada only).
CAUTION
1. For General Ventilating Use Only. Do Not Use To Exhaust
Hazardous Or Explosive Materials And Vapors.
2. Not for use in cooking areas. (Fig.B)
3. This product must properly connect to the grounding
conductor of the supply circuit.
4. To reduce the risk of injury to persons, install the fan at
Turning angle too large Duct shrink
ydobehtraenwoblEswobleynamooT
Body
45°
Cooking area
45°
Do not install above or
inside this area
Cooking
Equipment floor
Minimum 18 in.
Turning angle too large Duct shrink
ydobehtraenwoblEswobleynamooT
Body
45°
Cooking area
45°
Do not install above or
inside this area
Cooking
Equipment floor
Minimum 18 in.
Fig. A
Fig. B

4
GENERAL SAFETY INFORMATION
Model: VFB25ADBT
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct t
he interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
The Bluetooth word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
Delta Electronics, Inc. is under license. Other trademarks and
trade names are those of their respective owners.
The Bluetooth speaker complies with FCC radiation exposure
limits set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying exposure
compliance. This speaker must not be co-located or operate in
conjuction with any other antenna or transmitter. Changes or
modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this
equipment.
NOTE: The Grantee is not responsible for any changes or
modifications not expressly approved by the party responsible
for compliance. Such modifications could void the user's authority
to operate the equipment.
®
®
WARNING

Model: VFB25ADBT
5
PREPARATION
Tools Required for Assembly (not included): Hammer,
Flathead Screwdriver, Wire Nuts, Nails, Duct Tape,
Phillips Head Screwdriver, Utility Knife
Helpful Tools (not included): Electric Drill, Drill Bits
WARNING: Turn off electricity at breaker box
before beginning installation.
Carefully remove unit from carton.
Check area above installation location to be sure that
wiring can run to the planned location and that duct
proper ventilation.
Inspect duct work and wiring before proceeding with
installation.
Before installation, provide inspection and future
maintenance access at a location that will not
interfere with installation work.
You may need the help of a second person to install
this fan: one person on the attic side and one on the
room side.
Note: Installations may vary depending on how the
previous bath fan was installed. Supplies necessary
for the installation of your bath fan are not all included.
However, most are available at your local home
improvement or hardware store.
WIRING DIAGRAM
DIMENSION REQUIREMENTS
Ceiling
Opening (L)
Ceiling
Opening (W)
Ceiling
Opening (H)
10 1/4 in. 10 1/4 in. 8 1/2 in.
Housing
Dimension (L)
Housing
Dimension (W)
Housing
Dimension (H)
9 11/16 in. 9 11/16 in. 8 in.
The fan will operate most efficiently when located
where the shortest possible duct run and minimum
number of elbows will be needed.
Use a roof cap or wall cap that has a built-in damper
to reduce backdrafts.
Proper insulation around the fan to minimize building
heat loss and gain. 4” circular duct is recommended
for installation. The ducting from this fan to the outside
of building has a strong effect on the air flow, noise
and energy use of the fan. Use the shortest, straightest
duct routing possible for best performance, and avoid
installing the fan with smaller ductsthan recommended.
Insulation around the ducts can reduce energy loss and
inhibit mold growth. Fans installed with existing ducts
may not achieve their rated air flow.
External timer can be used please contact Delta
Breez customer service and consult with a licensed
electrician for compatibility
FAN SWITCH
JUNCTION BOX SWITCH BOX
BLACK
GREEN
GRD
OFF
ON
L
N
WHITE
OFF
ON
L
N
SPEAKER SWITCH
WHITE
BLUE
ON/OFF SWITCH
(purchase separately) SWITCH BOX
120 VAC
LINE IN
WIRING
PLATE
BLACK
WHITEGROUND
(bare)
BLUE
SPEAKER
SWITCH
FAN
SWITCH
Roof cap
(with built-in
damper)
Seal gap
around
housing
Caulk termination
to duct
Fan housing
Short piece of flexible
duct helps alignment
and absorbs
sound
or
Wall cap
(with built-in
damper)
Wall cap
(with built-in
damper)

6
ASSEMBLY INSTRUCTIONS
BEFORE INSTALLATION
Turn off power source. Review all safety precautions.
1. If spacing between joists is 12 in. apart, use four
long wood screws (provided) to attach the fan body
❶to ceiling joists.
Hardware
ALong wood screw
2. For joist spacing 16 in. - 24in., insert suspension
bracket I ❸into the bracket cover on the duct
connector side. Then, attach suspension bracket II
❹and bracket III ❺to the back of the fan body ❶.
3. Secure the fan body ❶to the joist with suspension
brackets ❸, ❹, ❺using long wood screws.
Hardware
ALong wood screw
4. Secure the suspension brackets ❹, ❺to the fan
body ❶using a short machine screw.
Hardware
BShort machine screw
NEW CONSTRUCTION – ATTACHING TO THE JOIST
5
3
4
1
2
A
1
Short
machine screw
1
1
4
4
5
A
5
3
Short
machine screw
1
1
4
4
5
A
5
4
Model: VFB25ADBT

7
ASSEMBLY INSTRUCTIONS
5. Remove the fan junction box cover a. Using wire
nuts (not supplied), connect house wires to fan
wires bas shown in the wiring diagram on page 5.
Reattach fan junction box cover c.
6. Connect a 4 in. circular duct a(not supplied)
and vent to the outside. Secure it with duct tape
(not supplied) or clamp (not supplied) to make the
connection secure and air tight.
Turn off power source. Review all safety precautions.
1. Remove existing fan.
2. Measure the opening to ensure it is large enough to
accommodate the new fan body (10 1/4 in. x 10 1/4
in.).
1
2
a
6
Model: VFB25ADBT
c
b
a
5
EXISTING CONSTRUCTION – ATTACHING TO JOIST
NOTE: ATTACHING DIRECTLY TO THE JOIST(S)
FROM BELOW WILL BE THE BEST INSTALLATION.
BEFORE INSTALLATION
7. Turn on power source. Check fan for any abnormal
sound or vibration.
3. If this fan is not replacing an old fan, be sure to cut
a 10 1/4 in. x 10 1/4 in. opening for the fan body
❶.
9.4"
9.4"
10 1/4 in.
10 1/4 in.
3

8
Model: VFB25ADBT
ASSEMBLY INSTRUCTIONS
5. Place the duct connector ❻through the ceiling cut
out. Connect a 4 in. circular duct (not supplied) a
and vent to the outside. Secure it with duct tape
(not supplied) or clamp (not supplied) to make
connection secure and air tight. Attach the duct
connector to the ceiling with one long wood screw.
Hardware
ALong wood screw
8. Insert fan body ❶into the ceiling cut out making
sure to align the duct connector with the fan body ❶.
7. Secure the fan body ❶from below using long wood
screws (provided). Insert at least 4 screws through
Hardware
ALong wood screw
6 Remove fan junction box cover. Using wire nuts
(not supplied), connect house wires to fan wires
aas shown in the wiring diagram on page 5.
9. Turn on the power source. Check fan for any
abnormal sound or vibration.
Install from below, no need for suspension
brackets (no attic access)
a
1A
A
6
3 1/2 in.
5
7
7
a
6
4. A piece of wood (not supplied) is screwed in from
below through the ceiling board. Suggested size is
1 in. x 3 in. x 14 in. Position the screws far enough
away from the edge of the ceiling board that it does
not crumble and give way. Put screws in both ends
of wood beyond the 10 1/4 in. hole. Keep screws in
range of grille.
Wood support screwed in from
underneath. Screw is far enough away
from the edge of sheetrock to prevent
crumblimg.
Wood support
4
1
8

9Model: VFB25ADBT
ASSEMBLY INSTRUCTIONS
c
b
a
4
a
5
1. For joist spacing 16 in. - 24in., insert suspension
bracket I ❸into the bracket cover on the duct
connector side. Then, attach suspension bracket II
❹and bracket III ❺to the back of the fan body ❶.
2. Secure the fan body ❶to the joist with suspension
brackets ❸, ❹, ❺using long wood screws.
Hardware
ALong wood screw
3. Secure the suspension brackets ❹,
❸, ❺to the fan
body ❶using a short machine screw.
Hardware
BShort machine screw
Install from above with suspension brackets
(attic access)
*ONLY IF UNABLE TO ATTACH DIRECTLY TO JOIST(S)
5
3
4
1
1
1
1
4
4
5
A
2
Short
machine screw
1
1
3
4
4
5
A
5
3
4. Remove the fan junction box cover a. Using wire
nuts (not supplied), connect house wires to fan
wires bas shown in the wiring diagram on page 5.
Reattach fan junction box cover c.
5. Connect a 4 in. circular duct a(not supplied)
and vent to the outside. Secure it with duct tape
(not supplied) or clamp (not supplied) to make the
connection secure and air tight.
6. Turn on power source. Check fan for any abnormal
sound or vibration.

Fan Mode: Turn the Fan switch to operate ON/OFF.
Speaker Mode: Turn the Speaker switch to operate ON/OFF.
Pairing your Bluetooth device to the speaker for the
first time
1. To play your personal music or audio files, you need
a Bluetooth device, like smart phone, tablet, or any
other such devices.
2. Place the Bluetooth device located within 10 meters
of the fan.
3. Set your device to midrange volume before connecting
to the speaker.
4. Turn ON the Speaker switch, the blue LED indicator
flashes in pairing mode.
5. Follow the instructions that came with your Bluetooth
device to make it discoverable or to set it to search for
other Bluetooth accessories. This may involve entering
a passkey or PIN( Personal Identification Number).
6. From the home screen, tap Settings > Bluetooth, the
device searches and a list of discoverable devices will
appear, choose "DeltaBreez SIG", and enter a passkey
or PIN (0000) if prompted.
7. When pairing is completed, the blue LED indicator
will solid on, you can use the Bluetooth speaker to
play music or audio files with your device.
10
GRILLE & SPEAKER INSTALLATION
OPERATION
Attach grille
2. ❷by pinching mounting springs aand
insert into the narrow rectangular slots in fan body ❶.
a1
2
1. Plug the Micro USB connector into the speaker
assembly , and secure the speaker assembly
to the holder on the fan unit.
7
Micro USB
1
7
2
Model: VFB25ADBT

11
See safety information before proceeding. Routine maintenance should be done at least once a year.
•Never use solvents, thinner or harsh chemicals when cleaning the fan.
•Do not allow water to enter the motor.
•Do not immerse metal parts in water.
•Do not immerse resin parts in water over 140º Fahrenheit.
•Do not immerse Bluetooth speaker in water.
Turn off power source. Review all safety precautions.
CARE AND MAINTENANCE
1. To remove grille ❷, squeeze springs and pull down.
2. Wash and clean the grille ❷in a sink and dry with a
cloth.
3. Remove dust and dirt from the fan body ❶with a vacuum
cleaner.
4. Dampen cloth with dust detergent and wipe the fan body
❶. Then wipe dry with a clean cloth.
5. Replace grille ❷back onto fan body ❶ .
6. Turn on power source to operate fan again.
1
2
1
Vacuum
cleaner
2
2
1
2
3
4
5
Model: VFB25ADBT

12
Model: VFB25ADBT
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The fan is not turning on 1. Power off
2. Faulty switch
3. Faulty wire connection
1. Make sure power supply is on.
2. Test or replace switch.
3. Check wire in switch box.
The fan seems louder
than it should
1. CFM too great
2. Damper not working
properly or damaged
3. Bend in duct too close
to fan discharge
4. Fan discharge
duct
5. Fan body not securely
attached
1. Be sure the CFM rating on the fan matches the
size of your room.
2. Check damper to ensure it is opening and closing
properly. If the damper has become damaged,
please call Customer Service.
3. Be sure you do not have any sharp bends in duct
closer than 18 in. to the fan discharge.
4. Use recommended size ducting to reduce fan
noise.
5. Be sure the fan is securely attached to your ceiling
joists.
The fan is not clearing
the room
1.
airfow within room
2.
1. Be sure a door or window is slightly ajar or opened
2. Be sure the CFM rating on the fan matches the
requirements for your room size.

13
DIMENSIONS
PRODUCT SPECIFICATIONS
Model No. Voltage Frequency Air Flow
@0.1” SP
Noise
@0.1” SP
Power
Consumption
Duct
Diameter Max Current
VFB25ADBT 110-220V 50-60Hz 110 CFM 1.0 Sone 21.4W 4 in. 0.3 AMPS
Weight
7.52 lbs.
SPECIFICATIONS
UNIT:INCH
Model: VFB25ADBT

14
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY
Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA that the Breez
ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3)
years from the original date of purchase.
Limitations and Exclusions
1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation
by the consumer. The warranty provided herein does not cover charges for labor or other costs incurred in the
troubleshooting, repair, removal, and installation service.
2. All returns of defective parts or products must include the product model number, and must be made through an
authorized Delta Electronics distributor. Authorized returns must be shipped prepaid. Repaired or replacement
products will be shipped by Delta Electronics F.O.B. shipping point.
3. Delta Electronics shall not be liable for any indirect, incidental, consequential, punitive, or special damages
arising out of or in connection with products use or performance, regardless of the form of action whether in
contract, tort (including negligence), strict product liability or otherwise.
4.
5. The warranty does not cover if user does not comply with manufacturer’s installation manual.
6. To qualify for warranty service, you must notify Delta Electronics at the address or telephone number below.
7. Delta Electronics shall have no liability to the original owner-user with respect to any defect caused by abuse,
misuse, neglect, improper transportation or storage, improper testing, improper installation, improper operation,
accident of products or parts thereof, or unusual deterioration or degradation of products or parts thereof due to
Address: 46101 Fremont Boulevard, Fremont, CA 94538
US Toll Free Number: 1-888-979-9889
www.deltabreez.com
Model: VFB25ADBT