Denon DN-470A User manual
User Guide English (3–6)
Guía del usuario Español (7–10)
Guide d’utilisation Français (11–14)
Guida per l’uso Italiano (15–18)
Benutzerhandbuch Deutsch (19–22)
Appendix English (23)
DENON
PROFESSIONAL
DN-470A
3
User Guide (English)
Introduction
Thank you for purchasing the DN-470A. At Denon Professional, performance and reliability
mean as much to us as they do to you. That’s why we design our equipment with only one
thing in mind—to make your performance the best it can be.
Box Contents
DN-470A
(2) 6-Pin Euroblock Connectors
(4) 4-Pin Euroblock Connectors
Power Cable
Rack Ears with Screws
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (documentation, technical specifications, system
requirements, compatibility information, etc.) and product registration, visit denonpro.com.
For additional product support, visit denonpro.com/support.
DENON
4
Features
Front Panel
1. Power Switch: Press this switch to power DN-470A on or off.
2. Level Knobs: Turn these knobs to set the output level for each channel.
3. Signal/Clip/Protection LEDs: These lights will illuminate different colors to show the
signal status of each channel input:
•Signal LED: The input’s Signal LED will be lit green when it is receiving a signal at
an optimal level.
•Clip LED: The input’s Clip LED is “peaking” when the LED is lit red (higher than 0 dB).
Turn its Level knob counter-clockwise or reduce the volume of the source to prevent
“clipping” (distortion).
•Protection LED: If the Protection LED turns red, the unit is in heat protection mode
and will not output sound. To restore sound output, reduce the temperature by making
sure there is good ventilation and by decreasing the signal level.
4. Air Intake Vents: Keep the vents clear from obstructions to allow air to flow through the
front grill for proper performance.
Rear Panel
1. Power Inlet: Use the included power cable to connect this input to a power outlet.
2. Fuse: If the unit’s fuse is broken, lift this tab to replace the fuse. Replace it with a fuse with
an appropriate rating. Using a fuse with an incorrect rating can damage the unit and/or fuse.
3. Inputs: Use Euroblock connectors to connect these channel inputs to your audio sources.
Each channel has a ground (G), cold/negative (–), and hot/positive (+) connector. Make
sure the wiring of each device matches each connection.
4. Outputs: Use Euroblock connectors to connect these channel outputs to your
loudspeakers. Each channel has a switch for 70V and 100V. Make sure the wiring of each
loudspeaker is done properly for each output.
5. Operation Mode Switch:Select the operation mode (70V or 100V) for each channel’s
output by moving the dip-switches to the desired position.
6. Exhaust Vents:Air from the front intake flows through the unit and exits here. For proper
performance, do not block the air vent.
1
2222
33
4
1
2
346
5
PRESET
1
22 22
33
4
1
2
346
5
DENON
5
ZONE2
SOURCE ZONE3 ZONE3
SOURCE STATUS DIMMER
VIDEO
AUX1
SETUPMIC
INTEGRATEDNETWORK AV RECEIVER
SSEERI
AVR-X4000
IN-Command
L- AUDIO - R
1CBL/SAT 3GAME 4NETWORK
QUICKSELECT
2Blu-ray
PHONES BACK
ENTER
INFO
SETUP
ZONE2
SOURCE SELECT
MASTER VOLUME
ON/OFF
AUX1
HDMI7 5V/1A
ON/OFF OPTION
Setup
Items not listed under Introduction >Box Contents are sold separately.
1. Use the included Euroblock connectors to connect the inputs on the rear panel to your
audio sources.
•Each channel input has a ground (G), cold/negative (–), and hot/positive (+) connector.
2. Use the included Euroblock connectors to connect the outputs on the rear panel to your
loudspeakers.
•Each channel output has a switch for 70V and 100V.
3. Use the included power cable to connect the power inlet to a power outlet.
4. Power on all of your audio sources (Blu-ray®players, stereos, microphones, amplifiers,
etc.).
5. Press the power switch to power on DN-470A.
6. Adjust the level knobs for each channel input as necessary.
Example
Blu-ray Player
Loudspeakers
Loudspeakers
Receiver
Power
A
6
Using a Euroblock Connector
1. Twist the speaker wire to form a tight strand and insert
this into the appropriate port, pushing the wire until it is
secured inside.
2. Attach the Euroblock connector to the terminal on
DN-470A.
3. To disconnect a wire, use a small screwdriver to press in
the spring above the insert port while pulling out the
wire.
Troubleshooting
If you encounter a problem, try doing these things first:
•Make sure all cables and other connected devices are properly and securely connected.
•Make sure you are using DN-470A as described in this user guide.
•Make sure your other devices or media are working properly.
•If you believe DN-470A is not working properly, check the following table for your
problem and solution.
Problem: Solution: Please see:
Power does not turn on. Make sure DN-470A’s power inlet is
properly connected to a power outlet
using the included power cable.
Setup
DN-470A does not
produce any sound, or
the sound is distorted.
Make sure all cable and device
connections are secure and correct.
Make sure none of the cables are
damaged.
Make sure the settings on your
loudspeaker, mixer, etc. are correct.
Setup
The sound has a hum or
noise.
Check the polarity of the input
connections.
If an unbalanced connection is used,
ensure terminal (-) is linked to GND.
If the clip LED is lit, reduce the output
volume.
Check the polarity of the speaker
connections.
Setup
CH A CH B CH C CH D
DENON
23
Appendix (English)
Technical Specifications
Total Harmonic Distortion < 0.1%
Frequency Response 100 Hz – 15 kHz (0+/-1 dBv)
Signal-to-Noise Ratio > 95 dB
Channel Separation > 70 dB
Output Power
(each channel)
120 W
Input Sensitivity 0.9-1.1V (0+/-1dBv)
Input Impedance 20
k
Ωbalanced or 10kΩunbalanced
Connectors (4) Euroblock channel outputs (70V, 100V)
(8) Euroblock channel inputs (ground, –, +)
(1) IEC power inlet
Power Connection: IEC
Input Voltage:
Japan: 100 V~, 50/60 Hz, 1000 W
US/CA: 110–120 V~, 50/60 Hz, 1000 W
EU/UK: 220–240 V~, 50/50 Hz, 1000 W
Dimensions
(width x depth x height)
19.0” x 11.1” x 1.7”
483 x 281 x 44 mm
Weight 10.4 lbs.
4.7 kg
Specifications are subject to change without notice.
Trademarks & Licenses
Denon is a trademark of D&M Holdings Inc., registered in the U.S. and other countries. Denon Professional
products are produced by inMusic Brands, Inc., Cumberland, RI 02864, USA. All other product names,
company names, trademarks, or trade names are those of their respective owners.
DENON
denonpro.com
Manual Version 1.2
DENON
PROFESSIONAL
Important Safety Instructions
& Warranty Information
lnstrucciones importantes de seguridad
e informaci6n
de
la garantfa
Instructions importantes de securite
et
informations de garantie
lstruzioni importanti di sicurezza
e le informazioni della garanzia
Wichtige Sicherheitsanweisungen
und Garantieinformationen
English (3-7)
Espanol (8-11)
Francais (12-15)
Italiano (16-19)
Deutsch (20-23)
Denon is a trademark
of
D&M Holdings Inc., registered in the U.S. and other countries. Denon Professional
products are produced
by
inMusic Brands, Inc., Cumber1and,
RI
02864
U.S.A
NEMA• is the registered trademark and service mark
of
the National Electrical ManufacturersAssociation.
All other product names, company names, trademarks,
or
trade names are those
of
their respective owners.
2
DENON
PROFE66l0/f/AL
1. What is covered
and
for how long?
Product Warranty
(for products purchased in the U.S.A.}
All
Products: inMusic Brands, Inc. ("inMusic") warrants
to
the original purchaser that Denon Professional
("Denon
Proj
products and all other accessories are free from defects in material and workmanship under
normal use and service
for
the
period commencing upon
the
date
of
purchase from an authorized Denon Pro
dealer and continuing
for
the
following period
of
time after that date
for
one
(1)
year. inMusic warrants factory-
refurbished merchandise
to
be free
of
material and operational defects
for
a period
of
ninety
(90)
days from the
original date
of
retail sale. This refurbished merchandise warranty is nottransferable.
2. What
is
not
covered? This Limited Warranty is conditioned upon proper use
of
the product
by
the purchaser. This
Limited Warranty does not cover:
(a)
damage caused by improper installation or improper connection to any
peripheral;
(b)
damage caused by
an
external electrical fault;
(c)
damage from use
of
parts not manufactured
or
sold
by Denon Pro;
(d)
product purchased from anyone other than
an
Denon Pro authorized dealer;
(e)
modifications
to
product not approved in writing by Denon Pro;
(f)
equipment that has the serial number removed
or
made illegible;
(g)
normal cosmetic and mechanical wear;
(h)
damage
or
loss during transit
to
an
Authorized Denon Pro Repair
Center; or
(i)
units that are purchased and/or located outside
of
thecontinental USA.
3.
What are inMusic's obligations? During the applicable warranty period, Denon Pro will repair or replace, at Denon
Pro's sole option, without charge
to
the purchaser, any defective component part
of
the product.
To
obtain service
under this Limited Warranty, purchaser must first contact Denon Pro and obtain a return merchant authorization
("RMA'1 number. Purchaser must then return the product
to
Denon Pro
in
an
adequate container for shipping,
accompanied by purchaser's sales receipt
or
comparable proof
of
sale showing the date
of
purchase, the serial
number
of
the product, and the seller's name and address. To obtain
an
RMA number and assistance on where
to
return the product, contact Denon Pro customer service at 401-658-5766. Upon receipt, Denon Pro will repair or
replace the defective products. Denon Pro may, at Denon Pro's sole option, use rebuilt, reconditioned, ornew parts
or
components when repairing any product
or
replace a product with a rebuilt, reconditioned, new
or
comparable
product. Repaired products will be warranted for a period equal
to
the remainder
of
the original Limited Warranty on
the original product or for 90 days, whichever is longer. All replaced parts, components, boards, and equipment
become the property
of
Denon Pro. If Denon Pro determines that any product is not covered by this Limited
Warranty, purchaser must payall parts, shipping, and labor charges forthe repair
or
return
of
such product.
4.
What are the
limits
on inMusic's liabilities? THE WARRANTIES GIVEN
IN
THIS LIMITED WARRANTY,
TOGETHER WITH ANY IMPLIED WARRANTIES COVERING DENON
PRO
PRODUCTS, INCLUDING WITHOUT
LIMITATION ANY WARRANTIES
OF
MERCHANTABILITY
OR
FITNESS
FOR
A PARTICULAR PURPOSE,
ARE
LIMITED TO THE DURATION
OF
THIS LIMITED WARRANTY.
EXCEPT
TO THE
EXTENT
PROHIBITED BY
APPLICABLE
LAW,
INMUSIC OR
DENON
PRO
SHALL NOT
BE
LIABLE
FOR
ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S
PROPERTY,
OR INJURY TO PURCHASER OR OTHERS ARISING OUT
OF
THE USE, MISUSE OR INABILITY TO
USE
ANY DENON PRO PRODUCT, BREACH OF WARRANTY,
OR
NEGLIGENCE, INCLUDING BUT NOT LIMITED
TO INMUSIC'S
OR
DENON PRO'S OWN NEGLIGENCE,
EVEN
IF
INMUSIC, DENON
PRO,
OR THEIR AGENTS
HAVE
BEEN
ADVISED
OF
SUCH DAMAGES,
OR
FOR
ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY
OTHER
PARTY.
THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR DENON
PRO
PRODUCTS, AND
IS
GIVEN
IN
LIEU
OF
ALI_ OTHER
EXPRESS
WARRANTIES. THIS LIMITED WARRANTY SHALL NOT
EXTEND
TO
ANYONE OTHER THAN THE ORIGINAL PURCHASER
OF
THIS PRODUCT AND
STATES
PURCHASER'S
EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY
IS
ILLEGAL
OR
UNENFORCEABLE BY
REASON
OF
ANY
LAW,
SUCH PARTIAL ILLEGALITY
OR
UNENFORCEABILTY SHALL NOT AFFECT THE
ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES
IS
AND WILLALWAYS
BE
CONSTRUED TO
BE
LIMITED BY
ITS
iERMS
OR
AS LIMITED AS THE LAW PERMITS.
This Limited Warranty allocates risk
of
product failure between purchaser and Denon Pro, and Denon Pro's
product pricing reflects this allocation
of
risk and the limitations
of
liability contained in this Limited Warranty.
The agents, employees, distributors, and dealers
of
Denon Pro are not authorized
to
make modifications
to
this
Limited Warranty,
or
make additional warranties binding on Denon Pro
or
inMusic. Accordingly, additional
statements such as dealer advertising or presentation, whether oral
or
written,
do
not constitute warranties
by
Denon Pro
or
inMusic and should not be relied upon.
5.
How
does state law apply to this
wa1T&nty?
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG
AN
IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS
OR
EXCLUSIONS MAY NOTAPPLY TO PURCHASER.
This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction
to
another.
Please record
the
serial number
of
your unit as shown on the back
of
the chassis as well as the name
of
the dealer
from whom you purchased the unit. Retain this information and your original purchase receipt
for
your records. Go
to
our
website denonpro.cem
to
register your product with us.
Model: Purchased From:
Serial Number: Date of Purchase:
3
DENON
,.OFE66l0NAL
Product Warranty
(for products purchased outside
of
the U.S.A.)
1. inMusic Brands, Inc.
("inMusicj
warrants to the original purchaser that Denon Professional
("Denon Pro'1 products are free from defects
in
material and workmanship under normal use and
service for the period commencing upon the date
of
purchase from an authorized Denon Pro
dealer and continuing
for
the following period
of
time after that datefor
(1)
Year.
2. This Limited Warranty is conditioned upon proper use
of
the product
by
the purchaser.
This Limited Warranty does not cover:
(a)
defects or damage resulting from accident, misuse,
abuse, neglect, unusual physical
or
electrical stress, modification
of
any part
of
the product,
or
cosmetic damage;
(b)
equipment that has the serial number removed or made illegible; (c) all
plastic surfaces and other externally exposed parts that are scratched
or
damaged due
to
normal use;
(d)
defects
or
damage from improper testing, operation, maintenance, installation,
adjustment,
or
service
of
the products.
3. During the applicable warranty period, Denon Pro will repair or replace,
at
Denon Pro's sole
discretion, without charge
to
the purchaser, any defective component part
of
the pro~uct. Denon
Pro may, at Denon Pro's sole discretion, use rebuilt, reconditioned,
or
new parts or components
when repairing any product
or
replace a product with a rebuilt, reconditioned, new or comparable
product. ·
4.
THE
WARRANTIES
GIVEN
IN
THIS
LIMITED
WARRANlY,
TOGETHER
WITH
ANY IMPLIED
WARRANTIES
COVERING
DENON
PRO
PRODUClS, INCLUDING WITHOUT LIMITATION ANY
WARRANTIES
OF MERCHANTABILllY
OR
FITNESS
FOR
A PARTICULAR
PURPOSE,
ARE
LIMITED
TO
THE
DURATION
OF
THIS LIMITED
WARRANlY.
EXCEPT
TO THE
EXTENT
PROHIBITED BY
APPLICABLE
LAW,
INMUSIC
OR
DENON
PRO
SHALL NOT
BE
LIABLE
FOR
ANY SPECIAL,
INCIDENTAL, CONSEQUENTIAL,
INDIRECT
OR
SIMILAR DAMAGES, LOSS
OF
PROFITS,
DAMAGES TO PURCHASER'S
PROPERTY,
OR
INJURY TO PURCHASER
OR
OTHERS
ARISING
OUT OF
THE
USE,
MISUSE
OR
INABILllY TO
USE
ANY DENON
PRO
PRODUCT,
BREACH OF
WARRANTY,
OR
NEGLIGENCE, INCLUDING BUT NOT LIMITED TO INMUSIC'S
OR
DENON
PRO'S
OWN
NEGLIGENCE,
EVEN
IF
INMUSIC,
DENON
PRO,
OR
ITS
AGENTS
HAVE
BEEN
ADVISED
OF
SUCH DAMAGES,
OR
FOR
ANY CLAIM BROUGHTAGAINST PURCHASER BYANY
OTHER
PARTY.
THIS LIMITED WARRANTY
IS
THE
COMPLETE WARRANTY
FOR
DENON
PRO'S PRODUCTS, AND
IS
GIVEN
IN
LIEU
OF
ALL
OTHER
EXPRESS
WARRANTIES.
THIS LIMITED WARRANTY SHALL NOT
EXTEND
TO ANYONE
OTHER
THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND
STATES
PURCHASER'S
EXCLUSIVE
REMEDY.
IF
ANY
PORTION
OF THIS LIMITED WARRANlY
IS
ILLEGAL
OR
UNENFORCEABLE BY
REASON
OF ANY
LAW,
SUCH
PARTIAL.
ILLEGALITY
OR
UNENFORCEABILTY SHALL NOT
AFFECT
THE
ENFORCEABILITY
OF
THE
REMAINDER OF THIS
LIMITED
WARRANTY WHICH
PURCHASER
ACKNOWLEDGES
IS
AND WILL
AL.WAYS
BE
CONSTRUED TO
BE
LIMITED BY
ITS
TERMS
OR
AS LIMITED
AS
THE
LAW
PERMITS.
This Limited Warranty allocates risk
of
product failure between purchaserand Denon Pro, and Denon
Pro's product pricing reflects this allocation
of
risk and the limitations
of
liability contained in this
Limited Warranty. The agents, employees, distributors, and dealers
of
Denon Pro are not authorized
to
make modifications
to
this Limited Warranty,
or
make additional warranties binding on Denon Pro
or
inMusic. Accordingly, additional statements such as dealer advertising
or
presentation, whether
oral or written,
do
not constitute warranties
by
Denon Pro
or
inMusic and should not be relied upon.
Some jurisdictions
do
not
allow limitations on
how
long an implied warranty lasts, so the above
limitation may not apply
to
you. This warranty gives you specific legal rights, and you may also have
other rights which vary under local laws.
Please record the serial number
of
your unit as shown on the back
of
the chassis as well as the name
of
the dealer from whom you purchased the unit. Retain this information and your original purchase
receipt for your records. Go
to
our
website denonpro.com to register your product with us.
Model: Purchased
From:
Serial Number: Date of Purchase:
4
Return Information
• A return merchant authorization number must be obtained from your local Denon Pro representative.
For your representative go to denonpro.com.
• A copy
of
the original sales receipt must also be included for the equipment
to
be repaired under
warranty.
• The faulty equipment must be packed
in
its original packaging.
• One additional outer layer
of
packaging must be included
to
ensure product safety. Failure
to
do
so may inadequately protect the equipment
in
transit and therefore jeopardize the warranty.
• Denon Pro will not accept COD shipments and no call tags will be issued for merchandise return.
• Denon Pro will not return repaired merchandise to customers by priority service except by written
request at the customer's cost. Requests must be submitted
in
writing with returned merchandise.
• The defective Denon Pro equipment should be sent freight prepaid with the return merchant
authorization number printed clearly on the outer packaging and original sales receipt enclosed
to
your local service center.
Very Important
Please read this section before connecting this unit to your system:
For optimum performance:
• All slide faders are subject
to
wear. Excessive force can wear out the faders quickly. User-
replaceable slide faders are not covered by our warranty.
• Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this
will void your warranty.
In
normal use, slide controls can last for many years. If they malfunction
(usually because
of
a dirty or dusty environment), consult a professional technician.
• Always make sure that AC power
is
off while making any connections.
• Use appropriate cables throughout your system. Do not use excessively long cables
(i.e.
over
32
feet / 10 meters).
Be
sure plugs and jacks are tightly mated. Loose connections can cause hum,
noise, or intermittents that could easily damage your speakers. Make the input and output
connections with readily available low-capacitance stereo cables. Cable quality makes a big
difference
in
audio fidelity and "punch." See your Denon Pro dealer or
an
electronics
or
audio
specialist store ifyou are not sure which cables
to
use.
• Never attempt
to
make any'adjustments other than those described in this manual, or repairs.
Take the unit to your dealer or
to
an
authorized Denon Pro service center.
• Always remember: turn amps on last and off first. Begin with master faders
or
volume controls
on minimum and the amplifier gain/input control(s) down. Wait
8-10
seconds before turning up
the volume. This prevents transients which may cause severe speaker damage.
• Use restraint when operating controls. Try
to
move them slowly. Rapid adjustments could damage
equipment due
to
amplifier clipping.
• Avoid amplifier "clipping" at all costs: this occurs when the red LEDs {usually on the front panel
of
most professional power amplifiers) start flashing. "Clipping" is when the power amplifier
is
distorting and working beyond its limits. Amplifier distortion
is
the main cause
of
speaker failure.
• To prevent fire or shock hazard, do not expose the unit
to
rain or moisture. Never place cans
of
beer, soda, glasses
of
water
or
anything wet near or on
top
of
the unit!
• Headphone outputs can be set
to
levels which can cause damage
to
your ears. Use caution.
• This unit may contain a microcomputer for signal processing and control functions.
In
very rare
situations, severe interference, noise from
an
external source, or static electricity may cause it to
lockup.
In
the unlikely event that this should happen, turn off the unit, wait at least five seconds,
and then turn it back on again.
• Under rare circumstances,
if
this product is exposed
to
electromagnetic interference during use,
there may be a slight drop
in
signal-to-noise ratio.
• Intended electromagnetic environments: residential, commercial, light industrial, urban outdoors.
5
Important Safety Instructions
1. Read and keep these instructions. Heed all warnings and follow all Instructions.
2. Do not use
this
apparatus near water (if applicable).
3. Clean only
with
dry
cloth.
4. Do
not
block
any
ventilation openings (If applicable). Install in accordance
with
the
manufacturer's instructions.
Do
not
install
this
equipment in a confined
or
"boxed-in"
space such as a bookcase
or
similar unit, and maintain
good
ventilation
conditions. The ventilation should
not
be
impeded
by
covering
the
ventilation openings
with
items such
as
newspaper,
tablecloths, curtains, etc.
5. Do not install near any heat sources such as radiators, heat registers, stoves,
or
other
apparatus Oncluding amplifiers) that
produce heat. Do
not
place exposed flame sources such as lighted candles
on
the
apparatus.
6. Do not defeat
the
safety purpose
of
the
polarized
or
grounding-type plug (if applicable). A polarized plug has
two
blades
with one
wider
than
the
other. A grounding
type
plug has
two
blades and a third grounding prong. The wide blade
or
the
third prong is provided
for
your
safety.
If
the
provided plug
does
not
fit
into
your
outlet, consult an electrician
for
replacement
of
the
obsolete outlet.
7. (If applicable) Protect
the
power
cord
from being walked on
or
pinched particularly
at
plugs, convenience receptacles, and
the
point
where
they
exit from
the
apparatus.
8. Only use attachment/accessories specified
by
the
manufacturer.
®)~
9. Use only
the
cart, stand, tripod, bracket
or
table specified
by
the
manufacturer,
or
sold with the apparatus
~if.
applicabl?)- When a cart
is
used, use caution when moving
the
cart/apparatus combination
to
avoid ,
""
1
1nJury
from tip-over.
1•
10. Unplug
this
apparatus during lightning storms
or
when unused
for
long periods
of
time.
~-=
11. Refer all servicing
to
qualified service personnel. Servicing is required when
the
apparatus has been damaged in any way,
such as
power-supply
cord
or
plug is damaged, liquid has been spilled
or
objects
have fallen into the apparatus, the
apparatus has been exposed
to
rain
or
moisture,
does
not
operate normally,
or
has been
dropped.
12. Power Sources
Of
applicable): This
product
should
be
connected
to
a
power
supply
only
of
the
type
described in these
operating instructions,
or
as marked on
the
unit.
13. lntemaVExtemal Voltage Selectors (if applicable): Internal orexternal voltage selectorswitches, if any, should only
be
reset and
re-equipped with a proper plug foralternative voltage
by
a qualified servicetechnician.
Do
not attempt
to
alterthis yourself.
14. Water and Moisture
(if
applicable): This product should be kept away from direct contact with liquids. The apparatus shall not
be exposed
to
dripping or splashing andthat no objects filled with liquids, such as vases, shall be placed on the apparatus.
15. Caution (if applicable): Danger
of
explosion if battery is incorrectly replaced. Replace
only
with
the
same
or
equivalent
type. Batteries
(a
battery
pack
or
an installed battery) shall
not
be
exposes
to
excessive heat such as sunshine, fire, etc.
16. (If applicable) Where
the
mains plug
or
an appliance coupler is used as
the
disconnect device,
the
disconnect device shall
remain readily operable.
17. Protective earthing terminal (if applicable): The apparatus should be
connected
to
a mains
socket
outlet with a
t.:i::\
protective earthing connection.
~
•
Denmark
(Danmark):
Apparatets stikprop
skal
tilsluttes
en
stikkontakt
med
jord, som giverforbindelse til
stikproppens
jord.
• Finland
(Suom,):
Laite on liitettava suojakoskettimilla varustettuun pistorasiaan.
• Norway
(Norge):
Apparatet mA tilkoples jordet stikkontakt.
• Sweden
(Sverige):
Apparaten skall anslutas till jordat uttag.
(g]
18. (If applicable) This symbol means the equipment is a Class
II
or
double-insulated electrical appliance.
It
has been D
designed in such a
way
that
it
does
not require a safety connection
to
electrical earth.
19. Warning (if applicable): Provide an earthing connection before
the
mains plug is connected
to
the
mains. When
disconnecting
the
earthing connection,
be
sure
to
disconnect it after pulling
the
mains plug
out
from
the
mains.
20. This apparatus is
for
professional use only. Intended operational climate: tropical, moderate.
21.
(If
applicable) When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable
tie).
Be
careful not
to
damage the power cord. Before using it again, make sure the power cord has not
been
damaged. If the power cord
has
been
damaged
atall, bring the unit and cord
to
a qualified service technician for repair
or
replacement as specified bythe manufacturer.
22. Warning (if applicable): Excessive sound pressure (high volumes) from headphones can cause hearing loss.
23. Warning (if applicable): Please refer
to
any important information (e.g., electrical, safety, etc.) printed
on
the
exterior
bottom
enclosure
or
rear panel before installing
or
operating
the
product.
Service Instructions
• Disconnect
power
cord
before servicing.
• Replace critical
components
.&.
only with factory parts or recommended equivalents.
• For
AC
line powered units: Before returning repaired unit
to
user, use an
ohmmeter
to
measure from both
AC
plug blades
to
all exposed metal parts. The resistance should be more than 2,000,000 ohms.
Safety Notices
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE & ·• i
ANY COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING I
Risk
of elecb"ic shock. Z
TO QUALIFIED SERVICE PERSONNEL ONLY.
■
Do notopen. 1
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within
the
equilateral triangle is intended
to
alert the user
to
the
presence
of
un-insulated "dangerous voltage" within
the
product's
enclosure that may be
of
sufficient magnitude
to
constitute a risk
of
electric shock.
SA
1965
INSTRUCTIONS: The exclamation
point
within
the
equilateral triangle is intended
to
alert the user
to
the presence
of
'I'
important operating and maintenance (servicing) instructions in
the
literature accompanying this appliance.
~
SA
1966
WARNING: To reduce
the
risk
of
fire
or
electrical shock,
do
not expose
this
appliance
to
rain
or
moisture. Electrical
equipment should NEVER
be
kept
or
stored in
damp
environments.
CAUTION
(for
U.S.A. & CANADIAN models
only):
TO PREVENT ELECTRIC
SHOCK
DO NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
6
NOTICE CONCERNING LASER PRODUCTS: DANGER: INVISIBLE LASER RADIATION
WHEN
OPEN
AND
INTERLOCK
FAILED
OR
DEFEATED. AVOID DIRECT EXPOSURE
TO
BEAM. USE
OF
CONTROLS
OR
ADJUSTMENTS
OTHER
THAN
THOSE
SPECIFIED HEREIN
MAY
RESULT IN
HAZARDOUS
RADIATION EXPOSURE.
NOTICE CONCERNING FCC REGULATIONS:
You
are cautioned
that
changes
or
modifications
not
expressly
approved
by
the
part responsible
for
compliance
could
void
the
user's authority
to
operate
the
equipment. This equipment ha$
been
tested
and
found
to
comply
with
the
limits
for
a Class B digital device, pursuant
to
Part
15
of
the
FCC rules.
These
limits are designed
to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses
and
can
radiate radio frequency energy
and,
if
not
installed and used in accordancewith
the
instructions,
may
cause harmful interference
to
radio communications. However,
there
is
no
guarantee
that
interference will
not
occur
in a particular installation.
If
this
equipment
does
cause hannful interference
to
radio
or
television reception,
which
can
be
determined
by
tuming
the
equipment
off
and
on, the
user is encouraged
to
try
to
correctthe interference
by
one
or
more
of
the
following measures:
(a)
reorient
or
relocate the receiving
antenna;
(b)
move
this unit;
(c)
increase
the
separation between
the
equipment
and
receiver;
(~
connect
the equipment
into
an
outlet
on
a circuit different from
that
to
which
the
receiver is connected;
(e)
be
sure
that
all cables are
property
shielded, using a
choke
or
ferrite where appropriate;
or
(~
consult
the
dealer
or
an experienced radio/television technician
for
help.
This
device
complies
with
Part
15
of
the
FCC rules.
Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
harmful interference,
and
(2)
this
device
must
accept
any
interference received, including interference
that
may
cause
undesired
operation.
FCC RF Radiation Exposure Statement: This
equipment
complies
with
FCC
radiation
exposure
limits
set
forth
for
an
uncontrolled
environment. End
users
must
follow
the
specific
operating
instructions
for
satisfying
RF
exposure
compliance.
This
transmitter
must
not
be
co-located
or
operating
in
conjunction
with
any
other
antenna
or
transmitter.
For Canadian models:
•
This
device
complies
with
Industry
Canada
licence-exempt
RSSs. Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
interference,
and
(2)
this
device
must
accept
any
interference,
including
interference
that
may
cause
undesired
operation
of
the
device.
•
Under
Industry
Canada
regulations,
this
radio
transmitter
may
only
operate
using
an
antenna
of
a
type
and
maximum
(or
lesser) gain
approved
for
the
transmitter
by
Industry
Canada.
To
reduce
potential
radio
interference
to
other
users,
the
antenna
type
and
its
gain
should
be
so
chosen
that
the
equivalent
isotropically
radiated
power
(e.i.r.p.) is
not
more
than
that
necessary
for
successful
communication.
• This radio
transmitter
(identify the
device
by
certification number,
or
model
number
if
Category
II)
has been
approved
by
Industry
Canada
to
operate
with
the
antenna
types
listed
below
with
the
maximum
permissible gain
and
required
antenna
impedance
for
each antenna type indicated.
Antenna
types
not
included
in
this
list, having a gain greaterthan
the
maximum
gain indicated
for
that
type,
are
strictly
prohibited
for
use
with
this
device. ·
•
This
unit
does
not
exceed
the
Class
B
limits
for
radio
noise
emission
from
digital
apparatus
set
out
in
the
radio
interference regulations
of
the
Canadian
Department
of
Communications.
_.
ESD/EFT
Warning:
This
unit
may
contain
a
microcomputer
for
signal
processing
and
control
functions.
In
very
rare
~
situations, severe interference,
noise
from
an external source,
or
static
electricity
may
cause
it
to
lock
up.
In
the
~
unlikely
event
that
this
should
happen,
tum
off
the
unit,
wait
at
least
five
seconds,
and
then
tum
it
back
on
again.
The
pins
of
connectors
identified
with
this
ESD
warning
symbol
should
not
be
touched.
For
best
audio
quality,
avoid
using
this
device
in
a high RF-radiated
environment.
In
an
environment
with
radio
frequency
interference,
the
unit
may
malfunction
and
resume
normal
operation
after
removal
of
the
interference.
For
240-volt
use
in
U.K.,
use
NEMA
•
-style
240-volt
plug.
For
other
countries
use
proper
plug
for
local outlet.
Double-Insulated:
When
servicing
use
only
identical
replacement
parts.
Correct
Disposal
o1
This Product: This
marking
indicates
that
this
product
should
not
be
disposed
with
other
household
wastes
throughout
the
EU.
To
prevent
possible
harm
to
the
environment
or
human
health
from
uncontrolled
waste
disposal,
recycle
it
responsibly
to
promote
the
sustainable
reuse
of
material resources.
To
return
-
your
.
used
device,
please
use
the
return
and
collection
systems
or
contact
the
retailer
where
the
product
was
purchased.
They
can
take
this
product
for
environmentally
safe
recycling.
Disposal
of
Batteries (if applicable):
• Neverdisposeof
any
types of batteries in
fire
or
near
excessive
heat
or
direct sunlight. Overheated batteries
ca,
rupture orexplode.
•
If
you
are unsure of
how
or
where
to
dispose
of
a battery, refer
to
your
local ordinances
for
the
properlocation, method, etc.
•
Alkaline
batteries
&
lithium
button
cell
batteries:
You
can
safely
dispose
of
alkaline
and
lithium
button
cell
batteries
with
normal
household
waste.
They
do
not
pose
a health
or
environmental risk
during
normal
use
or
disposal. (Alkaline
batteries
are
composed
primarily
of
common
metals
like steel, zinc,
and
manganese.)
Do
not
dispose
of
large
amounts
of
alkaline
or
lithium
button
cell
batteries
in
a
group.
Used
batteries
are
often
not
completely
"dead."
Grouping
them
together
can
bring
these
"live"
batteries
into
contact
with
one
another, creating
safety
risks.
To
avoid
this,
insulate
each
battery
with
tape
or
other
non-conductive
material
to
ensure
it
does
not
discharge.
Proven
cost-effective
and
environmentally
safe
recycling
processes
are
not
yet
universally available
for
alkaline
and
lithium
button
cell batteries.
Some
communities
offer
recycling
or
collection
of
these
batteries.
For
more
information,
refer
to
your
local
ordinances
or
contact
your
local
government.
• Lead-acid batteries:
Dispose
of
lead-acid
batteries
by
bringing
them
to
an
electronic
waste
center
or
recycling
center,
or
dispose
of
them
in
accordance
with
your
local
ordinances.
(Rechargeable
lead-acid
batteries are
the
same
type
used
in
automobiles
and
should
be
disposed
of
in a similarfashion.)
California
Proposition 65 Warning: This
product
may
contain
chemicals
known
to
the
State
of
California
to
cause
cancer
and
birth
defects
or
other
reprodllci:ive harm. (California
law
requires
this
warning
to
be
given
to
customers
in
the
State
of
California.)
CE
General Note
on
the Declaration
o1
Confonnity:
We
hereby declare
that
this
device is in
inMusic
GmbH
accordance with the essential requirements
of
the
European Directive 2014/53/EU.
The
full EU Harkortstr.
12
-
32
declaration
of
conformity can
be
requested
at
the
address
shown
here
or
at
40880
Ratingen
denonpro.com/safety
GERMANY
7
World Headquarters inMusic Brands, Inc.
200 Scenic View Drive
Cumberland,
RI
02864
USA
Tel: 401-658-5766
Fax:401-658-3640
U.K. Office· inMusic Europe, Ltd.
Unit 3, Nexus Park
Lysons Avenue
Ash-Vale
HAMPSHIRE
GU12
SQE
UNITED KINGDOM
Tel: 01252 896 040
Fax: 01252 896
021
Germany Office inMusic GmbH
Harkortstr. 12 -32
40880 Ratingen
GERMANY
Tel: 02102 7402 20150
Fax: 02102 7402 20011
denonpro.com
7-51-1332-C
Other manuals for DN-470A
1
Table of contents
Other Denon Amplifier manuals
Denon
Denon AVP-A1HD User manual
Denon
Denon POA-A1HDCI User guide
Denon
Denon DN-A300M User manual
Denon
Denon AVC-X8500HA User manual
Denon
Denon PRA-S10 User manual
Denon
Denon PMA-A100 User manual
Denon
Denon PMA-850 User manual
Denon
Denon HEOS LINK User manual
Denon
Denon DN-500AV User manual
Denon
Denon AVC-X3800H User manual
Denon
Denon PMA-50 User manual
Denon
Denon DN-500AV Technical manual
Denon
Denon PMA-1055R User manual
Denon
Denon POA-A1HDCI User manual
Denon
Denon DN-A300M User manual
Denon
Denon DN-A100 User manual
Denon
Denon AVC-A110 User manual
Denon
Denon AVP-A1HD User manual
Denon
Denon PMA-510 User manual
Denon
Denon PMA-2500NE User manual
