DeVilbiss HFRL-508 User manual

SB-6-146-R1 (5/2018) 1 / 4 www.carlisleft.com
Risk of personal injury.
Risk of property damage.
Except as otherwise specified by the manufacturer, this
product is specifically designed for compressed air service
and use with any other fluid (liquid or gas) is a misap-
plication. For example, use with or injection of certain
hazardous gases in the system (such as oxygen or liquid
petroleum gas) could be harmful to the unit or result in a
combustible condition that may cause fire or explosion.
Manufacturer’s warranties are void in the event of misap-
plication and manufacturer assumes no responsibility for
any resulting loss.
DESCRIPTION
This 100 CFM filter (Model HAF-502) is designed to remove dirt, pipe
scale and most liquid aerosol. It includes a 5 micron filter element. A
model with 50 CFM air regulator is also available (Model HFRL-508).
Specifications
Air Filter:
Air Inlet 1/2" NPT(F)
Air Outlet 1/2" NPT(F)
Air Flow Capacity 100 CFM
Maximum Temp. 150° F (65.6° C)
Max. Inlet Pressure 150 psig (10.3 bar)
Max. Operating Pressure 150 psig (10.3 bar)
Air Connections Model HFRL-508:
Regulated Non-Regulated
(1) 1/4" NPS(M) (1) 1/4" NPS(M)
(1) Plugged Port
INSTALLATION
Risk of injury. Release all air pressure from system
before servicing system. Do not place unit in ser-
vice without metal bowl guard installed. Plastic bowl
units are sold only with metal bowl guards. To minimize the
danger of flying fragments in the event of plastic bowl failure,
guard must not be removed. If the unit is in service without
the metal bowl guard installed, manufacturer's warranties
are void and the manufacturer assumes no responsibility
for a resulting loss. If unit has been in service and does not
have a metal bowl guard, order one and install before plac-
ing back in service.
Certain solvents, paints and chemicals may attack plastic bowl
and can cause bowl failure. Do not use near these materials.
IMPORTANT:
Read and follow all instructions and SAFETY PRECAUTIONS before
using this equipment. Retain for future reference.
1. Be sure to read all "WARNINGS"and "CAUTIONS"in
this manual and on the unit before installation or using this
equipment.
2. Install filter as close as possible to point where air is
being used. Install main air shut-off valve and standard
pipe union (supplied by user) upstream of filter to allow main-
tenance to unit.
3. Install unit with air flow through filter in direction of arrow on
top of unit.
4. Minimum 1/2" piping is recommended. Avoid using
fittings, couplings, etc. that restrict air flow.
5. A 1/2" street elbow will be needed to allow vertical pipe instal-
lation. Mount filter in a vertical position.
6. Do not install filter in an application where the pressure drop
will exceed 20 psi. For example, a quick opening valve located
upstream from the filter could cause a momentary pressure drop
in excess of 20 psi.
7. Install "T" handle into regulator (Model HFRL-508).
8. Maximum inlet pressure and operating temperature is:
150 PSIG (10.3 bar) and 150° F (65.6° C).
9. A 6' length of vinyl tubing is shipped loose with the unit. Slide
over automatic drain which protrudes from bottom of bowl. Place
other end of vinyl tubing into appropriate receptacle (i.e. below
booth grating, can, etc.). Prevent vinyl tubing from becoming
kinked which would prevent free movement of liquids discharged
from the automatic drain.
10. An optional manual drain (HAF-11) is supplied loose in the
carton (see item 10, Fig. 2). If desired, this can be installed
in place of the automatic drain.
OPERATION
After unit is installed and ready to use:
1. Attach air hose(s) to outlet ball valve(s), selecting regulated and/
or non-regulation according to the application.
2. Open main shut-off valve upstream of filter.
3. Main line air pressure is monitored by the top air gauge.
4. Adjust regulator to desired setting by turning "T" handle
in or out.
5. Open ball valve(s) to supply air to spray gun or tool being
used. With air flowing, readjust air pressure at regulator
if necessary.
6. After use, shut off ball valve(s) and bleed off residual air in hose(s).
MAINTENANCE
Certain solvents, paints and chemicals may attack plastic
bowl and can cause bowl failure. Do not use near these ma-
terials. When bowl becomes dirty, wipe only with a clean, dry
cloth. Immediately replace any crazed, cracked, damaged or
deteriorated plastic bowl with a new plastic bowl. Reinstall
metal bowl guard.
1. If bowl is equipped with manual drain, drain bowl at least once
per shift. Units with automatic drain will drain automatically.
2. Before performing maintenance on unit, close main
shut-off valve located upstream of filter. Bleed off residual air
in unit.
3. To open filter, press button located on clamp ring and
rotate ring either clockwise or counterclockwise. The metal bowl
guard and plastic bowl can then be removed from the filter head.
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and understand this manual. Contact your local DeVilbiss representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS DEVILBISS PRODUCT.
EN
SERVICE MANUAL
HFRL-508 60 CFM FILTER-REGULATOR
HAF-502 100 CFM FILTER

EN
SB-6-146-R1 (5/2018)2 / 4www.carlisleft.com
4. Remove the filter element by loosening the baffle counter-
clockwise. Clean or replace the filter element. The element
can be cleaned by blowing off with a duster gun (clean from
inside out). Frequency of element cleaning/replacement
will depend upon air quality, air usage, and condition of the
air piping. It is recommended to check and clean/replace
the element every 3-6 months.
5. Inspect o-ring (2) for damage. Replace if necessary.
6. Inspect plastic bowl for signs of damage such as cracks,
crazing or deterioration. Replace if necessary. See "Caution"
at beginning of "Maintenance" section, page 1.
Note
Do not wash plastic bowl with the automatic drain installed.
Water can get into the float mechanism, causing the drain
to malfunction. Remove the automatic drain before clean-
ing the plastic bowl with soap and water (no solvents).
Do not place unit in service without metal bowl
guard installed.
7. Before placing unit back into service, make sure plastic
bowl and metal bowl guard are properly installed and se-
curely locked in place.
8. Confirm automatic drain operates properly after unit is in
operation. Replace if necessary.
Ind.
Ref Replacement Parts
No. Part No. Description Req.
1 HAF-502 Air Filter, 100 CFM, See Fig.2 1
2 HAF-21 Cross Manifold 1
3 GA-288 Air Gauge, 0-160 psi (main line) 1
4 83-2727 Air Gauge, 0-100 psi (regulated) 1
5 HAR-507 Air Regulator (See Fig. 3) 1
6 — 1/4" Street Elbow, 90° 1
7 VA-542 Ball Valve 2
PARTS LIST – Model HFRL-508FIGURE 1 MODEL HFRL-508 FILTER/REGULATOR (60 CFM)
FIGURE 2 MODEL HAF-502 FILTER (100 CFM)
1
6
5
4
3
2
8
7
10
(Optional)
9
1
5
4
3
2
7
6
Ind.
Ref Replacement Parts
No. Part No. Description Req.
1 — Cover 1
2 — O-Ring 1
3 HAF-26 Baffle Kit 1
4 HAF-6 Filter and O-Ring Kit 1
5 HAF-18 Automatic Drain (Std.) 1
6 HAF-8 Plastic Bowl 1
7 HAF-19 Metal Bowl Guard 1
8 HAF-409 Clamp Ring 1
9 — 1/2 x 3/8 Vinyl Tubing, 6 ft. 1
10 HAF-11 Manual Drain (Optional, 1
shipped loose)
PARTS LIST - Model HAF-502
CA PROP
65
PROP 65 WARNING
WARNING: This product contains
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.

EN
SB-6-146-R1 (5/2018) 3 / 4 www.carlisleft.com
Individual
Ref Replacement Parts
No. Part No. Description Required
1 --- #10-32 x 9/16 Fillister 6
Hd. Screw
2 HAR-14 Cover 1
3 --- Spring Button 1
4 --- Diaphragm Spring 1
5 --- Body 1
6 --- Pipe Plug 1/4" NPT(M) 1
7 --- Bottom Plug 1
8 KK-4977 Repair Kit (includes 1
Items 9 thru 14)
9 --- Diaphragm Assembly 1
10 --- O-Ring 1
11 --- Valve 1
12 --- O-Ring 1
13 --- Spring 1
14 --- O-Ring 1
7
14
13
1
2
3
4
9
10
11
12
6
5
8
PARTS LIST - Model HAR-507 Regulator AssemblyFIGURE 3 HAR-507 AIR REGULATOR, 60 CFM
REGULATOR MAINTENANCE
1. Occasionally remove bottom plug (7) and clean valve seat
(11) and body. Clean parts with denatured alcohol, wipe off
seat and blow out body with compressed air.
2. To disassemble regulator, remove screws, bonnet, spring and
spring button. Diaphragm assembly can now be removed.
3. Check all o-rings for signs of damage. Replace if necessary.
4. Reassemble parts. Center stem of valve in hole of regulator
body. Screw bottom plug into body.
Note
Erratic operation or loss of regulation is usually due
to dirt in the valve area and cleaning is necessary. If
cleaning does not correct the problem, replace the items
included in Repair Kit KK-4977. If unit leaks air at A,
install Repair Kit KK-4977.
A
ACCESSORIES
HAF-407 BRACKET ASSEMBLY KIT – Used with HAF-502 and HFRL-508.

EN
SB-6-146-R1 (5/2018)4 / 4www.carlisleft.com
WARRANTY POLICY
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,
will void all warranties. Failure to reasonably follow any maintenance guidance provided
may invalidate any warranty.
For specic warranty information please contact Carlisle Fluid Technologies.
For technical assistance or to locate an authorized distributor,
contact one of our international sales and customer support locations.
Region Industrial/Automotive Automotive Renishing
Americas Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]
Europe, Africa,
Middle East, India
Tel: [phone]
Fax: [phone]
China Tel: [phone]
Fax: [phone]
Japan Tel: [phone]
Fax: [phone]
Australia Tel: [phone]
Fax: [phone]
Carlisle Fluid Technologies is a global leader in innovative nishing technologies.
Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.
DeVilbiss®, Ransburg®, ms®, BGK®, and Binks®
are registered trademarks of Carlisle Fluid Technologies, Inc.
©2018 Carlisle Fluid Technologies, Inc.
All rights reserved.
For the latest information about our products, visit www.carlisleft.com