DFI KS156P-EHL User manual

KS156P-EHL & KS215P-EHL
15.6" & 21.5" Industrial Touch Panel PC
User’s Manual
© October 06, 2023 DFI Inc.

2
User's Manual | KS156P-EHL & KS215P-EHL
Copyright
This publication contains information that is protected by copyright. No part of it may be repro-
duced in any form or by any means or used to make any transformation/adaptation without the
prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions or
changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2023. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for com-
pliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.

3
User's Manual | KS156P-EHL & KS215P-EHL
Table of Contents
Chapter 1 - Introduction................................................................................................................6
Overview..................................................................................................................................6
I/O Views..........................................................................................................................6
Dimensions.............................................................................................................................6
KS156P-EHL.....................................................................................................................6
KS215P-EHL.....................................................................................................................6
Key Features...........................................................................................................................7
Specifications.........................................................................................................................8
Chapter 2 - Hardware Installations............................................................................................10
Removing the Chassis Cover ..............................................................................................10
Installing an M.2 Card .........................................................................................................11
Installing an Antenna...........................................................................................................12
Mounting Options.................................................................................................................13
Wall Mount.....................................................................................................................13
Panel Mount - KS156P-EHL..........................................................................................14
Panel Mount - KS215P-EHL..........................................................................................15
Chapter 3 - System Settings......................................................................................................16
System Layout......................................................................................................................16
Top View ........................................................................................................................16
Bottom View...................................................................................................................16
Jumper Settings...................................................................................................................17
CLEAR CMOS Data........................................................................................................17
Panel Backlight Selection.............................................................................................17
Panel Inverter Power Selection....................................................................................18
Panel VDD Power Jumper ............................................................................................18
COM1 Power Selection.................................................................................................19
COM2 Power Selection.................................................................................................19
Pin Assignment....................................................................................................................20
USB Ports.......................................................................................................................20
Front Audio.....................................................................................................................20
Digital I/O Connector.....................................................................................................21
Cooling Fan Connectors................................................................................................21
COM (Serial) ports.........................................................................................................22
InnoAGE HDR1...............................................................................................................23
COM (Serial) ports.........................................................................................................23
InnoAGE HDR1...............................................................................................................24
Front Panel.....................................................................................................................24
Battery Header...............................................................................................................25
S/PDIF Connector..........................................................................................................25
DIO Power ......................................................................................................................26
LVDS Backlight...............................................................................................................26
SATA Power ...................................................................................................................27
Heater.............................................................................................................................27
Chapter 4 - BIOS Settings...........................................................................................................28
Overview ...............................................................................................................................28
Main.......................................................................................................................................29
Advanced .............................................................................................................................29
RC ACPI Settings...........................................................................................................30
CPU Configuration.........................................................................................................30
Power & Performance...................................................................................................31
PCH-FW Configuration..................................................................................................31
Trusted Computing........................................................................................................32
NCT6126D Super IO Configuration..............................................................................32
NCT6126D Super IO Configuration ►Serial Port 1, 2 Configuration ..................33
NCT6126D Super IO Configuration ►Serial Port 3, 4 Configuration ..................33
NCT6126D Super IO Configuration ►Serial Port 5, 6 Configuration ..................34
NCT6126D HW Monitor ................................................................................................34
Smart Fan Function.......................................................................................................35
Serial Port Console Redirection ...................................................................................35
Serial Port Console Redirection ►Console Redirection Settings.........................36
USB Configuration ........................................................................................................36
Network Stack Configuration........................................................................................37
USB Power Control........................................................................................................37
Chipset..................................................................................................................................38
System Agent (SA) Configuration................................................................................38
PCH-IO Configuration....................................................................................................39
PCH-IO Configuration►PCI Express Configuration.............................................39
PCH-IO Configuration►SATA Configuration .......................................................40
PCH-IO Configuration►Audio Configuration.......................................................40
Security .................................................................................................................................41
Secure Boot....................................................................................................................41
Boot.......................................................................................................................................42
Save & Exit............................................................................................................................42
Updating the BIOS................................................................................................................43
Notice: BIOS SPI ROM..........................................................................................................43

4
User's Manual | KS156P-EHL & KS215P-EHL
About this Manual
This manual can be retrieved from the website.
The manual is subject to change and update without notice, and may be based on editions that
do not resemble your actual products. Please visit our website or contact our sales representa-
tives for the latest editions.
Warranty
1. Warranty does not cover damages or failures that arises from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper
installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether
in or out of warranty. It must be returned to the purchase point, factory or authorized
service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to
the product that has been modified or altered.
About this Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 Touch Panel PC
• 1 Quick Installation Guide
Note: The items are subject to change in the developing stage.Note: The items are subject to change in the developing stage.
The product and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.

5
User's Manual | KS156P-EHL & KS215P-EHL
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you
are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, con-
tacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or
connectors by their ends.
Safety Precautions
• Use the correct DC / AC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging in
the power cord.
• There is danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent specifications of batteries recommend by
the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humid environments.
• Make sure the system is placed or mounted correctly and stably to prevent the chance
of dropping or falling may cause damage.
• The openings on the system shall not be blocked and shall be kept in distance from
other objects to make sure of proper air ventilation to protect the system from over-
heating.
• Dress the cables, especially the power cord, so they will not be stepped on, in contact
with high temperature surfaces, or cause any tripping hazards.
• Do not place anything on top of the power cord. Use a power cord that has been ap-
proved for use with the system and is compliant with the voltage and current ranges
required by the system’s electrical specifications.
• If the system is to be unused or stored for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system is physically damaged.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground
the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet
does not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the electricity outlet before cleaning. Use a damp cloth
for cleaning the surface. Do not use liquid or spray detergents for cleaning.
• Before connecting, make sure that the power supply voltage is correct. The device is
connected to a power outlet which should be grounded connection.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other
components. Perform the upgrade instruction procedures described at an ESD
workstation only. If such a station is not available, you can provide some ESD pro-
tection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
The system may burn fingers while running.
Wait for 30 minutes to handle electronic parts after power off.

6
Chapter 1
INTRODUCTION
User's Manual | KS156P-EHL & KS215P-EHL
Chapter 1 - Introduction
X Overview
I/O Views KS156P-EHL
KS215P-EHL
1
2
3
4
DC-In
DP++
HDMI
2.5G LAN
5
6
7
8
9
USB 3.2 Gen1
Line-Out
COM Ports 1~4
Power Button
USB 3.2 Gen2
X Dimensions
521.74
323.74
24.50
54.10
353.00
188.00 43.8991.86
84.3784.37
20.00
2.00
9.00
3.80
2.00
9.00
20.00
7
2
1
3
6
45
8
9
7

7
Chapter 1
INTRODUCTION
User's Manual | KS156P-EHL & KS215P-EHL
X Key Features
CPU Performance:
Intel®Atom®x6425E Processor, Quad Core
Intel®Atom®x6413E Processor, Quad Core
Touch Type:
Projected Capacitive Touch
Dual Display:
HDMI & DP++
Multiple Expansions:
M.2 2242/2280/3052 B Key
M.2 2230 E Key
Wide Voltage:
Support 9 ~ 36V

8
Chapter 1
INTRODUCTION
User's Manual | KS156P-EHL & KS215P-EHL
X Specifications
DISPLAY AND
TOUCH SCREEN Display KS156P-EHL: 15.6" TFT LCD Panel
KS215P-EHL: 21.5" TFT LCD Panel
Contrast 16 : 9
Max. Resolution 1920 x 1080
Touch Type Projected Capacitive
Brightness KS156P-EHL: 400 (cd/m2)
KS215P-EHL: 300 (cd/m2)
Backlight Lifetime 50,000 (hours)
SYSTEM Processor Intel®Atom®x6425E Processor, Quad Core, 1.5M Cache, 2.0GHz (3.0GHz), 12W
Intel®Atom®x6413E Processor, Quad Core, 1.5M Cache, 1.5GHz (3.0GHz), 9W
Memory Two 260-pin SODIMM up to 32GB
Dual channel DDR4 up to 3200MHz
BIOS AMI SPI 256Mbit (supports UEFI boot only)
GRAPHICS Controller Intel®UHD Graphics
Feature OpenGL 4.5, DirectX 12, Open CL 1.2, Vulkan 1.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H.265, VP8, VP9
HW Encode: AVC/H.264, JPEG/MJPEG, HEVC/H.265, VP9
Display 1 x DP++
DP++: resolution up to 4096x2160 @ 60Hz
1 x HDMI 2.0
HDMI: resolution up to 4096x2160 @ 24Hz
Dual Displays DP++ & HDMI
STORAGE External 1 x 2.5" SATA 3.0 Drive Bay
EXPANSION Interface 1 x M.2 2242/2280/3052 B Key (PCIe x1/SATA/USB2.0)
1 x M.2 2230 E Key (PCIe x1/USB2.0)
1 x Nano SIM Socket (connected to M.2 B key)
I/O Ethernet 2 x GbE (RJ-45)
Serial 2 x RS-232/422/485
2 x RS-232
USB 2 x USB 3.2 Gen2
2 x USB 3.2 Gen1
Display 1 x DP++
1 x HDMI
Audio 1 x Line-Out
Button 1 x Power Button

9
Chapter 1
INTRODUCTION
User's Manual | KS156P-EHL & KS215P-EHL
POWER Type DC 9-36V
Connector DC Jack
MECHANISM Construction Plastic + Sheet Metal
Mounting VESA Mount 100 x 100
IP Rating IP65 Front Panel Protection Without Power Button
Dimensions(W x H x D) KS156P-EHL: 392 x 256 x 51.7 mm
KS215P-EHL: 521.8 X 323.8 X 54.1 mm
Weight KS156P-EHL: 4.1 Kg
KS215P-EHL: 7.0 Kg
ENVIRONMENT Operating Temperature 0°C ~ 50°C
Storage Temperature -30°C ~ 80°C
Relative Humidity 10 to 95% @ 40°C, non-condensing
STANDARDS AND
CERTIFICATIONS Shock OP: Half-sine, 3G @ 11ms Non-OP: Half-sine, 5G @ 11ms
Vibration OP: Random, 1Grms @ 5~500Hz, 30min
Non-OP: Sweep sine, 3Grms @ 10~500Hz, 30min
Certifications CE, FCC, Class A, UKCA

10
Chapter 2
HARDWARE INSTALLATION
User's Manual | KS156P-EHL & KS215P-EHL
Chapter 2 - Hardware Installations
X Removing the Chassis Cover
Please observe the following guidelines and follow the instructions to open the system.
1. Make sure the system and all other peripheral devices connected to it have been powered off.
2. Disconnect all power cords and cables.
Step 1:
The 8 screws of the system are used to secure the cover to the chassis. Remove the screws and
put them in a safe place for later use.
Step 2:
Lift the cover to open the system.

11
Chapter 2
HARDWARE INSTALLATION
User's Manual | KS156P-EHL & KS215P-EHL
X Installing an M.2 Card
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
Before installing the M.2 module into the M.2 socket, please make sure that the following
safety cautions are well-attended.
1. Make sure the PC and all other peripheral devices connected to it has been powered
down.
2. Disconnect all power cords and cables.
3. Locate the M.2 socket on the system board
4. Make sure the notch on card is aligned to the key on the socket.
5. Make sure the standoff screw is removed from the standoff.
M.2 Module M.2 Socket
Key
Stand-off
Notch

12
Chapter 2
HARDWARE INSTALLATION
User's Manual | KS156P-EHL & KS215P-EHL
Please follow the steps below to install the card into the socket.
Step 2:
Press the end of the card far
from the socket down until
against the stand-off.
Step 3:
Screw tight the card onto the
stand-off with a screw driver
and a stand-off screw until
the gap between the card and
the stand-off closes up. The
card should be lying parallel to
the board when it’s correctly
mounted.
Step 1:
Insert the card into the socket
at an angle while making sure
the notch and key are perfectly
aligned.
M.2 Module M.2 Socket
Key
Stand-off
Notch
X Installing an Antenna
Before installing the antenna, please make sure that the following safety cautions are wellat-
tended.
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
Step 1:
There are antenna holes reserved on the rear side of the system and covered by rubber plugs.
Please remove the plug prior to installing an antenna.
Step 2:
Connect the internal cable to the board's antenna connector, screw the antenna connector
through the antenna hole with washers and nuts, and screw on the antenna as illustrated
below.
Antenna ConnectorCableModule Connector NutWasher
Chassis Wall Antenna

13
Chapter 2
HARDWARE INSTALLATION
User's Manual | KS156P-EHL & KS215P-EHL
X Mounting Options
Wall mount bracket 1 Wall mount bracket 2
Screw
Wall Mount
Step 1:
Select a place on the wall where you will mount the Panel PC.
Step 2:
Use the provided mounting screws to attach wall mount bracket 1 onto the wall.
Step 3:
Attach the other bracket (wall mount bracket 2) to the rear of the Panel PC.
Step 4:
Slide the Panel PC to wall mount bracket 1 and attach the two brackets together with the
hooks. Then tighten the screw to secure the assembly in place.

14
Chapter 2
HARDWARE INSTALLATION
User's Manual | KS156P-EHL & KS215P-EHL
Panel Mount - KS156P-EHL
Step 1:
Select a place on the panel (or wall) where you will mount the Panel PC.
Step 2:
Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (359mm x
194mm) and ensure that the Panel PC can be fitted into the panel properly.
The flat panel thickness is less than 3mm. Be sure to route or trim down the thick wall to 3 mm
or slightly less for the clamps to recess and be compatible with your wall or enclosure.
Step 5:
The first and second clamps must be positioned and secured diagonally prior to mounting the
rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the
white plastic cap onto the back of the panel. The illustration below shows that all clamps are
properly mounted.
Step 3:
Insert the Panel PC from the outside surface of the panel into the mounting hole until it is
properly fitted against the panel.
Step 4:
Position the mounting clamps along the rear edges of the Panel PC and insert them into the
slits around the Panel PC.

15
Chapter 2
HARDWARE INSTALLATION
User's Manual | KS156P-EHL & KS215P-EHL
Panel Mount - KS215P-EHL
Step 1:
Select a place on the panel (or wall) where you will mount the Panel PC.
Step 2:
Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (359mm x
194mm) and ensure that the Panel PC can be fitted into the panel properly.
The flat panel thickness is less than 3mm. Be sure to route or trim down the thick wall to 3 mm
or slightly less for the clamps to recess and be compatible with your wall or enclosure.
Step 5:
The first and second clamps must be positioned and secured diagonally prior to mounting the
rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the
white plastic cap onto the back of the panel. The illustration below shows that all clamps are
properly mounted.
Step 3:
Insert the Panel PC from the outside surface of the panel into the mounting hole until it is
properly fitted against the panel.
Step 4:
Position the mounting clamps along the rear edges of the Panel PC and insert them into the
slits around the Panel PC.

16
Chapter 3
SYSTEM SETTINGS
User's Manual | KS156P-EHL & KS215P-EHL
Chapter 3 - System Settings
X System Layout
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
Front
Audio
PCIE1
12
9
10
1
2
9
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
JP6
3
1
SPI Flash BIOS
1
2
9
TPM
1
1
1 2
39 40
1
40
VGA
DP2
DP1
HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
M.2 B Key
2242
2260
2280
M.2 E Key
2230
LVDS
eDP
SYS FAN 2
1
1
3
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SIM Card
slot
Top View Bottom View

17
Chapter 3
SYSTEM SETTINGS
User's Manual | KS156P-EHL & KS215P-EHL
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
X Jumper Settings
11
33
2-3 On: 5V1-2 On: 3.3V (default)
CLEAR CMOS Data Panel Backlight Selection
1-2 On: Normal (default)
11
11
2-3 On: Clear CMOS Data

18
Chapter 3
SYSTEM SETTINGS
User's Manual | KS156P-EHL & KS215P-EHL
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
1
3
2-3 On: 5V
1-2 On: 12V (default)
Panel Inverter Power Selection Panel VDD Power Jumper
11
666
555
222
111
1-2 On: 12V 3-4 On: 5V 5-6 On: 3.3V (default)
1
6

19
Chapter 3
SYSTEM SETTINGS
User's Manual | KS156P-EHL & KS215P-EHL
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
COM1 Power Selection COM2 Power Selection
66
66
55
55
22
22
11
11
1-3/2-4 On: RS232 Standard (default) 1-3/2-4 On: RS232 Standard (default)
3-5/4-6 On: RS232 With Power 3-5/4-6 On: RS232 With Power
1
6
1
6

20
Chapter 3
SYSTEM SETTINGS
User's Manual | KS156P-EHL & KS215P-EHL
X Pin Assignment
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
Heater
12
9
12
9
12
9
12
9
12
9
12
9
S/PDIF
1 5
InnoAGE
HDR1
PCIE1
12
910
1
2
9
Line Out
12V DC-IN
DDR4_1 SODIMM (Top)
DDR4_2 SODIMM (Bottom)
Buzzer
Front Panel
12
2
111
3
1
SPI Flash BIOS
1
2
9
1
DIO
1
1 2
39 40
1
40
DP2HDMI
LAN1
(2.5G)
LAN2
(2.5G)
USB 0/1USB 2/3
USB4/5
(USB2.0) USB6/7 (USB2.0)
SATA0
SATA1
COM
1/2/3/4/5/6
(top to bottom)
M.2 B Key
2242
2260
2280
M.2 E Key
2230
DIO Power
LVDS
eDP
SYS FAN 2
CPU/SYS FAN 1
1
1
JP1
1
Battery
1 1
6 6
TSJP2 TSJP1
SATA0/1 Power (up to down)
1
1
1
1
Front
Audio
DPJP2
DPJP1
6
1
JP2
1 2
13 14
J3
1 DPJ1
11
DPJP3
1
6
12
6
J14
USB Ports Front Audio
1
2
9
Pin Function Pin Function
15V_USB45(67) 25V_USB45(67)
3USB2_4(6)_C_N 4USB2_5(7)_C_N
5USB2_4(6)_C_P 6USB2_5(7)_C_P
7GND 8GND
9--- 10 N.C.
12
910
Pin Function Pin Function
1MIC2-L 2AGND_AUDIO
3MIC2-R 4N.C.
5LINE2-R 6MIC2-JD
7AGND_AUDIO 8--
9LINE2-L 10 LINE2-JD