DFI DT200-CS User manual

© March 28, 2023 DFI Inc.
www.dfi.com
DT200-CS
MiniITX System with MXM
Quick Installation Guide
Package Contents
• 1 DT200-CS System Unit
• 3 M.2 Slot Screws
• 2 MXM Module Screws
• 1 ADDM UL Battery Addendum
• Thermal Grease(X-23-7783D) Injector 1g

Quick Reference | DT200-CS 1
Product Overview
Front View
1
2
3
4
5
Power Button
Power LED
HDD LED
COM1
COM2
12
7
36
45
6
7
USB 2.0
2.5" SSD Slot

Rear View
10
11
DC-in
HDMI
DP (From MXM)
Giga LAN
8910 12 13
11
15
14
8
9
12
13
14
MIC-In
Line-Out
Grounding
USB 3.0
15
Quick Reference | DT200-CS 2

Removing the Chassis Cover
Please observe the following guidelines and follow the instructions to open the system.
1. Make sure the system and all other peripheral devices connected to it have been
powered off.
2. Disconnect all power cords and cables.
Step 1:
The 6 screws on both front and rear sides of the system and the 8 screws on the left and right
sides of the system are used to secure the cover to the chassis. Remove the screws and put
them in a safe place for later use.
Front View
Rear View
Left View
Right View
Quick Reference | DT200-CS 3

Step 2:
Lift the cover to open the system.
Step 3:
The boards can be easily accessed after the chassis cover is removed.
Quick Reference | DT200-CS 4

Installing an M.2 Card
Please observe the following guidelines and follow the instructions to open the system.
1. Make sure the system and all other peripheral devices connected to it have been
powered off.
2. Disconnect all power cords and cables.
Step 1:
There are 4 screws on the bottom of the system are used to secure the M.2 cover to the
chassis. Remove the screws and put them in a safe place for later use.
Quick Reference | DT200-CS 5

Step 2:
Lift the cover to open the system.
Quick Reference | DT200-CS 6

M.2 Module M.2 Socket
Key
Stand-off
Notch
Step 5:
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap
between the card and the stand-off closes up. The card should be lying parallel to the board
when it’s correctly mounted.
Step 3:
Please follow the steps below to install the card into the socket.
Insert the card into the socket at an angle while making sure the notch and key are perfectly
aligned.
Step 4:
Press the end of the card far from the socket down until against the stand-off.
M.2 Module M.2 Socket
Key
Stand-off
Notch
M.2 Module M.2 Socket
Key
Stand-off
Notch
Quick Reference | DT200-CS 7

Installing an MXM Card
Before installing an MXM card, please make sure that the following safety cautions
are wellattended.
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
Step 1:
Lift the cover to open the system.
The board can be easily accessed and you will find the location of the MXM card socket.
Step 2:
Please follow the steps below to install an MXM card into the socket.
Insert an MXM card into the socket at an angle while making sure the notch and key are
perfectly aligned.
Quick Reference | DT200-CS 8

The List of Compactible MXM modules is as follows:
Model Assignment Assignment
P1000 512 47W
P2000 768 58W
T1000 896 50W
PTX3000 1920 80W
Step 3:
Screw tight the card through the holes with the motherboard to keep it steady until the gap
closes up. The card should be lying parallel to the board when it’s correctly mounted.
Quick Reference | DT200-CS 9

Installing an MXM cooler
Step 1:
Align the mounting screws of the cooler with the mounting holes of the module.
Tighten four screws to install the cooler onto the module.
Please follow the steps below to attach an MXM cooler to the MXM module.
*An MXM cooler is an optional accessory, customers can purchase it if necessary.
1
34
2
Quick Reference | DT200-CS 10

Step 2:
Connect the cable to the fan connector on the board.
The List of Optional items is as follows:
ltem Name Part Number Description
CPU cooler
A71-103004-000G For 35W, Height: 37.3mm
A71-103005-000G For 65W, Height: 45.3mm
MXM Quadro T1000 612-M3T100-100G 50W, 896 CUDA Cores, 2.6 TFLOPS, 0~55°C
MXM Quadro RTX3000 612-M3T300-000G 80W, 1290 CUDA Cores, 5.4 TFLOPS, 0~55°C
Fan PWR Y-cable for
MXM(RTX3000) A81-009614-016G 1*3P/2.5mm to 1*3P/2.54mm to
1*4P/1.25mm, L=50mm
MXM Cooler A71-110100-000G MXM cooler for RTX3000 87x106.35x34
MXM cooler for T1000 73x60x32.1mm
Quick Reference | DT200-CS 11

Insterting a 2.5" HDD/SDD
Step 1:
There is a 2.5" HDD/SDD slot on the frong side of the system.
Step 2:
Pull the silver latch to unlock the door.
Quick Reference | DT200-CS 12

Step 3:
Slide the drive into the slot until the drive is fully seated.
Close the drive latch to lock the drive in place.
Important:
Excessive force may damage its mechanical parts.
If the HDD/SSD is inserted backward into the slot, forcing the device
may damage the slot.
Quick Reference | DT200-CS 13

System Layout
MADE IN TAIWAN
DIO
DCIN_19V
DPA/DPB
DP_HDMI
USB2_1/2 USB3_1/2
DPC/DPD
LAN1
LAN2
USB2_3/4 USB3_3/4
LAN3/4
MXM3.1-B
AUDIO
SYS_FAN
DIO Power
LPC
CN59.G4
Front Panel
SATA0(R3) SATA1(R2)
COM2
COM1
USB2_5/6
EDP
CPU_FAN
CN59.G3
MXM
1
1
1
1
1
11
1
2
2
2
2
10
11
1
1
1
1
1
2
2
13 14
8
1
1
1
1
1
2
9
10
1
2
3
4
7
5
6
16
10
9
11
12 13 14 15
17
8
18 19
20
21
22
24
23
Quick Reference | DT200-CS 14

Front Audio
M.2 Power
System Fan Power
DIO Power
DIO
LPC
Front Panel
SATA Power
SATA0
SATA1
LCD Panel Power
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
LCD/eDP
USB 2.0
COM1
COM2
Clear CMOS Jumper
17
18
19
20
CPU Fan
Battery
DIMM1
DIMM2
21
22
23
24
CPU Cooler
6x USB 2.0 Hub Riser Card
System Fan
2.5" SATA SSD/HDD Tray
Quick Reference | DT200-CS 15

Clear CMOS Jumper JP1
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
16
M.2 Power M2JP204
3V3SB (default) 1-2 On
3V3 2-3 On
2
Jumper Settings
Quick Reference | DT200-CS 16

PIN Assignment
XCPU Fan
17
Pin Assignment
1Ground
212V
3RPM
4CTRL
XDIO Power
4
Pin Assignment
112V
2GND
35VSB
45V
XDIO
5
Pin Assignment Pin Assignment
1D_IOA0_C 2D_IOA1_C
3D_IOA2_C 4D_IOA3_C
5D_IOA4_C 6D_IOA5_C
7D_IOA6_C 8D_IOA7_C
XSATA Power
8
Pin Assignment
1N.C
2GND
3GND
4+5V
XSATA (Serial ATA)
9 10
Pin Assignment
1GND
2TX+
3TX-
4GND
5RX-
6RX+
7GND
Quick Reference | DT200-CS 17

XUSB 2.0
13
XCOM (Serial) Port
14
Pin Assignment Pin Assignment
1MDCD1(2)- 2MRD1(2)
3MTD1(2) 4MDTR1(2)-
5GND 6MDSR1(2)-
7MRTS1(2)-8MCTS1(2)-
9MRI1(2)-10 ---
15
XFront Audio
1
Pin Assignment Pin Assignment
1Mic2-L 2GND
3Mic2-R 4N.C.
5Line2-R 6Mic2-JD
7GND 8--
9Line2-L 10 Line2-JD
Pin Assignment Pin Assignment
1SBV4 2SBV4
3USBP_C_5N 4USBP_C_6N
5USBP_C_5P 6USBP_C_6P
7GND 8GND
9-- 10 N.C
Quick Reference | DT200-CS 18

XFront Panel
7
Pin Assignment Pin Assignment
1NC
Power/
Standby
LED
2V_SUS_LED
HDD-LED
33V3 4V_SUS_LED
5HD_LED 6SUS_LED
RESET
7GND
Power
Button
8GND
9SYS_RST 10 PWR_BTN-
11 NC 12 ---
XLPC
6
Pin Assignment Pin Assignment
1CLK 2LAD1
3RST# 4LAD0
5FRAME# 6VCC3
7LAD3 8GND1
9LAD2 10 ---
11 SERIRQ 12 GND2
13 5VSB 14 5V
DFI reserves the right to change the specifications at any
time prior to the product's release. This QR may be based
on the product’s revision. For more documentation and
drivers, please visit the download page at www.dfi.com/
downloadcenter, or via the QR codes to the right.
Quick Reference | DT200-CS 19