Digital Projection 119-712B User manual

Rev B September 2019
Titan Laser WUXGA
High Brightness Digital Video Projector
INSTALLATION & QUICK START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REFERENCE GUIDE
119-712B

Digital Projection Ltd. Titan Laser WUXGA About this document
About this document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this document
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are
closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice.
Updates may be available online. Please visit the Digital Projection website for all latest documents.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners. Digital Projection disclaims any proprietary interest in
trademarks and trade names other than its own.
Copyright © 2019Digital Projection Ltd. All rights reserved.
Rev B September 2019
page 2
Introduction
Notes

Laser information Digital Projection Ltd. Titan Laser WUXGA
Laser information
Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation
exposure.
Optical radiation
Caution - possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be harmful to eyes. This
projector is tested according to IEC/EN62471-5:2015 (Photobiological safety of lamps and lamp systems – Part 5: Image projectors standard) and is
Risk Group 3 (high risk).
Introduction Rev B September 2019
page 3
Notes

Digital Projection Ltd. Titan Laser WUXGA Light Hazard Warning
Light Hazard Warning
No direct exposure to the
beam is permitted, RG3
IEC 62471-5:2015.
Operators should control
access to the beam
within the hazard
distance or install the
projector at sufficient
height to prevent
exposures of spectators’
eyes within the hazard
distance.
Hazard Distance
The hazard distance is the distance measured from the
projection lens at which the intensity or energy per unit of
surface is lower than the applicable exposure limit on the
cornea or skin. If the person is within the hazard distance, the
beam is considered unsafe for exposure.
Light Hazard Distances
LENS HAZARD DISTANCE
0.67 : 1 Super Wide fixed 2m
1.12 : 1 Wide Fixed 3.5m
1.16-1.49:1 Super Wide Zoom 5.5m
1.39 - 1.87:1 Wide Zoom 6.5m
1.87 - 2.56:1 Standard Zoom 8.5m
2.56 - 4.16:1 Semi Long Zoom 10.5m
4.16 - 6.96:1 Long Zoom1 14m
6.92 - 10.36:1 Long Zoom2
Rev B September 2019
page 4
Introduction
Notes

Introduction Digital Projection Ltd. Titan Laser WUXGA
Introduction
This manual describes both the Titan Laser 37000 WU Series and Titan Laser 29000 WU.
Congratulations on your purchase of this Digital Projection product. Your projector has the following key features:
lWUXGA projector.
lSupport for Frame Sequential and Dual Pipe 3D formats.
lHDBaseT® for transmission of uncompressed High Definition Video up to 100 m from the source.
l3G-SDI with loop-through.
lEdge Blend with black level correction.
lBlanking control for custom input window sizing.
lCornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
lControl via LAN and RS232.
lMotorised lens mount.
lSeparate control of screen and source aspect ratio.
lNon-linear warp for irregular projection surfaces.
A serial number is located on the side of the projector. Record it here:
Introduction Rev B September 2019
page 5
Notes

Digital Projection Ltd. Titan Laser WUXGA Contents
About this document 2
Symbols used in this document 2
Product revision 2
Legal notice 2
Laser information 3
Optical radiation 3
Light Hazard Warning 4
Light Hazard Distances 4
Introduction 5
Contents 6
What's in the box? 12
Connecting the power supply 13
Projector overview 14
Control panel 15
Remote control 17
Infrared reception 20
Positioning the screen and projector 21
Roll and pitch 22
Stacking and rigging 23
Pin and cup stacking 23
Using the eye bolts 24
Point-to point connections 24
Threaded suspension cables 25
Changing the lens 26
Inserting a new lens 26
Removing the lens 26
Fitting a lens hood 27
Fitting a lens stabilizing bracket 28
Operating the projector 32
Switching the projector on 32
Switching the projector off 32
Selecting an input signal 32
Selecting a test pattern 32
Adjusting the lens 33
Lens menu 33
Remote control 33
Adjusting the image 33
Orientation 33
Geometry 33
Picture 33
Signal inputs 36
Digital inputs and outputs 36
EDID on the DisplayPort, HDMI, and HDbaseT inputs 37
Using DisplayPort/ HDMI/ HDBaseT switchers with the projector 37
3D connections 38
Frame sequential 1080p 3D up to 120Hz and WUXGA 3D at 100Hz 38
Dual Pipe 1080p and WUXGA 3D sources at up to 100 and 120Hz 38
3D Sync 39
Control connections 40
LAN connection examples 41
RS232 connection example 42
Using the menus 44
Rev B September 2019
page 6
Introduction
Notes
Contents

Contents Digital Projection Ltd. Titan Laser WUXGA
Opening the Menu 44
Opening a submenu 44
Exiting menus and closing the OSD 45
Inside a menu 45
Accessing sub menus 46
Executing commands 46
Editing projector settings 47
Using a slider to set a value 47
Editing numeric values 48
Using the projector 49
Main menu 49
Lens menu 50
Lens control 50
Lens memory 51
Image menu 52
Color menu 54
Color space 54
Color mode 55
ColorMax 55
Manual color matching 56
Color matching parameters explained 57
Color temperature 58
Gains and lifts 58
Geometry menu 59
Aspect ratio 59
Theaterscope setting 60
Digital zoom 61
Overscan 62
Blanking 63
Keystone 64
Keystone example 65
Keystone settings 66
4 corners 67
Top right corner example 68
Rotation 69
Rotation example 70
Pincushion / barrel 71
Pincushion/ Barrel example 71
Arc 72
Custom warp 73
Edge blend menu 74
Blend start 75
Blend width 76
Black level uplift 77
3D menu 78
3D types 79
Some 3D settings explained 80
Dark time 80
Eye swap 80
Sync offset 81
Laser menu 82
Setup menu 83
ColorMax 85
Measured data/ target data 86
Introduction Rev B September 2019
page 7
Notes

Digital Projection Ltd. Titan Laser WUXGA Contents
Power on / off 87
Clock adjust 88
PIC mute setting 88
OSDsettings 89
Memory 89
EDID Mode 90
Hotkey setting 90
Network menu 91
Network setup 92
Art-net setup 92
Art-net channel setting 93
PIP menu 94
Information menu 95
Signal format 95
System status 96
Thermal status 96
Factory reset 97
Served web pages 98
Choosing a lens 108
Basic calculation 109
Basic calculation example 110
Full lens calculation 111
Introducing TRC 111
Calculating TRC 112
TRC table 112
Calculating the throw ratio with TRC 112
Full lens calculation example 113
Screen requirements 114
Fitting the image to the display 114
WUXGA images displayed full width 114
WUXGA images displayed with a height of 1200 pixels 114
WUXGA images displayed full height 115
Diagonal screen sizes 115
Positioning the image 116
Aspect ratios explained 118
Aspect ratios examples 118
Source: 4:3 118
Source: 16:9 119
Source: 16:10 (native) 119
Aspect ratio example: TheatreScope 120
Appendix A: supported signal input modes 121
2D formats 121
3D formats 124
SDI formats 125
Appendix B: wiring details 126
Signal inputs and outputs 126
HDMI 1 and 2 126
DisplayPort 127
3G-SDI in, 3G-SDI out 128
HDBaseT input 128
Control connections 129
LAN 129
RS232 129
IR input 129
Rev B September 2019
page 8
Introduction
Notes

Contents Digital Projection Ltd. Titan Laser WUXGA
Appendix C: memory scheme and memory items 130
Appendix D: glossary of terms 133
Introduction Rev B September 2019
page 9
Notes

Digital Projection Ltd. Titan Laser WUXGA
Rev B September 2019
This page is intentionally left blank

Rev B September 2019
Titan LaserWUXGA
High Brightness Digital Video Projector
INSTALLATION & QUICK START GUIDE
119-712B

Digital Projection Ltd. Titan Laser WUXGA What's in the box?
What's in the box?
Make sure your box
contains everything listed.
If any pieces are missing,
contact your dealer.
Only one remote is
supplied with the
projector.
Save and store the
original box and packing
materials, in case you
ever need to ship your
projector.
The projector is shipped
without a lens.
Only the appropriate cable
for destination territory is
supplied with the projector
Projector
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Remote Control Batteries
Important Information Book Lens Stabilizing Bracket HDMI Cable Remote Control Cable
Power Cable, UK / RoW Power Cable, USA only
Rev B September 2019
page 12
Installation & Quick Start Guide
Notes

Connecting the power supply Digital Projection Ltd. Titan Laser WUXGA
Connecting the power supply
Use only the power cable
provided.
Ensure that the power
outlet includes a ground
connection as this
equipment MUST be
earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a
damaged power cable.
The USA model can
operate at 110V or 200V.
Voltage selection is
automatic, but the
projector must be
powered off before
switching power outlets.
Light output power is
reduced to approx 30%
when using the USA
model and operating on
110V.
Rest of the World:
1
2
1. Firmly push the mains connector into the socket
2. Rotate the connector 90° clockwise to lock it in place
USA Only
1. Firmly push the mains connector into the socket
2
2. Rotate the connector 90° clockwise to lock it in place
Installation & Quick Start Guide Rev B September 2019
page 13
Notes

Digital Projection Ltd. Titan Laser WUXGA Projector overview
Projector overview
6
7
1
3
2
4
5
Front View
1. Eye bolts
2. Connections panel
3. Stacking pins (x4)
4. Adjustable feet (x4)
5. Stacking cups (x4)
6. Control panel
7. Mains socket and switch
Rev B September 2019
page 14
Installation & Quick Start Guide
Notes

Control panel Digital Projection Ltd. Titan Laser WUXGA
Control panel
1
2
4
6
9
10
3
5
7
8
12
14
15
16
13
11
EXITMENU
STATUS
LENS
SHIFT
ZOOMFOCUS
POWER INPUT PIC MUTE
CENTER
LENS LIGHT TEMP
AUTO
SYNC
ASPECT
HOTKEYS
1
2
3
Control Panel
AUTO SYNC and
ASPECT do not work
when the projector uses
HDMI 3 or 4.
1. POWER
Switches the projector on and off (STANDBY).
Indicator:
Off. The projector is switched off
Flashing green. The projector is warming up
Flashing blue. The projector is cooling down
On, red. Standby mode
On, green. The projector is switched on.
2. INPUT
Switches to the next input source.
3. AUTO SYNC
Re-synchronises with the current input signal.
4. ASPECT
Changes the aspect ratio.
5. CENTER LENS
Centers the lens.
6. PIC MUTESwitches the laser off/on or blanks the DMD.
Indicator:
Off = the projector is in standby
On, blue = the projector is on, normal projection
On, red = the projector is on, picture mute is activated
7. LIGHT INDICATOR
Off = light is switched off
Flashing red (cycles of single flashes) = failure to light up during power up
Flashing red (cycles of double flashes) = unexpected light off while running
On, green = light is switched on
8. TEMP INDICATOR
Off = no problem
Flashing red = temperature error
9. HOTKEYS
User selectable functions.
Pre-set functions:
HOTKEY 1 Information
HOTKEY 2 Test Pattern
HOTKEY 3 Lens Memory Load
Additional options: Picture Mode, Ambient Brightness Correction, Freeze, PIP Swap.
HOTKEY 3 is used when a lens adapter is installed. Whilst in standby mode, press and hold HOTKEY 3 for five seconds to run center lens before installing
the lens.
Installation & Quick Start Guide Rev B September 2019
page 15
Notes

Digital Projection Ltd. Titan Laser WUXGA Control panel
10. STATUS
Off = no problem
Flashing red (continuously) = cover error
Flashing red (cycles of four flashes) = fan error
On, red = system error
11. MENU
Displays and exits the OSD.
12. Arrow buttons & ENTER
Navigation buttons used to highlight menu entries in the OSD. Press ENTER to open or execute the highlighted menu entry.
13. EXIT
Exits the current OSD page and enters the level above.
14. LENS SHIFT
Arrow buttons move the lens in the specified direction.
15. FOCUS
Plus and minus buttons move the focus in and out.
16. ZOOM
Plus and minus buttons zoom in and out.
Rev B September 2019
page 16
Installation & Quick Start Guide
Notes

Remote control Digital Projection Ltd. Titan Laser WUXGA
Remote control
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
8
6
5
4
3
2
1
7
9
10
Remote Control
1. Power ON / OFF
Turns power on and off.
The PIC Mute setting is
defined in the setup menu.
See Setup menu on
page83
2. Pic Mute OPEN / CLOSE
Shows and hides the projected image.
There are two PIC Mute settings:
lLaser. When off, the laser is switched off and no image is projected
lDMD Blanking. When off, the laser remains on and a black image is projected
3. OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD during
projection.
4. MENU
Access the OSD. If the OSD is open, press this button to go back to the previous menu.
5. Navigation (arrows and OK)
Navigate through the menus with the arrows, confirm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens.
See 11 below. In lens adjustment modes, or when the OSD is not showing, the OK button
switches between modes: Shift Adjustment and Zoom / Focus Adjustment.
6. EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
FREEZE and RE-SYNC
are not available when the
projector uses input HDMI
3 or 4.
7. FREEZE
Freeze the current frame.
8. DEFAULT
When editing a parameter, press this button to restore the default value.
9. INFO
Access information about the projector.
10. RE-SYNC
Re-synchronise with the current input signal
Installation & Quick Start Guide Rev B September 2019
page 17
Notes

Digital Projection Ltd. Titan Laser WUXGA Remote control
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
11
13
12
14
15
16
Remote Control
If focus cannot be
achieved using the focus
in / out feature, press Shift
&7 to adjust for far focus,
or Shift & 8 to adjust for
near focus.
11. LENS adjustment
lFOCUS IN / OUT: adjust focus.
lSHIFT: press and hold this button, then use the Navigation arrow buttons to move the
lens.
lZOOM IN / OUT: adjust zoom.
12. USER PRESET A, B, C, D
Load user presets.
13. ALT
Press and hold this button to access alternative functions for all buttons with a green label.
This projector does not
use the following options
on the remote: DVI, VGA,
COMP 1 and COMP 2.
3D is only available on the
HDMI 3 and 4 inputs.
14. DVI / DisplayPort2 / numeric input 3
There is no DVI input on this projector.
Use with ALT to select the DisplayPort 2 input.
15. HDMI 2 / HDMI 4 / numeric input 2
Select the HDMI 2 input.
Use with ALT to select the HDMI 4 input.There is no HDMI 4 input on this projector
16. HDMI 1 / HDMI 3 / numeric input 1
Select the HDMI 1 input.
Use with ALT to select the HDMI 3 input.There is no HDMI input on this projector
Rev B September 2019
page 18
Installation & Quick Start Guide
Notes

Remote control Digital Projection Ltd. Titan Laser WUXGA
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1 HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
17
23
19
21
22
24
18
20
Remote Control
17. DISPLAYPORT 1 / R / numeric input 4
Select DisplayPort 1 input.
18. HD-T / G / numeric input 5
Select the HDBaseT input.
This projector does not
use the following options
on the remote: DVI, VGA,
COMP 1 and COMP 2.
3D is only available on the
HDMI 3 and 4 inputs.
PIP is not available when
the projector uses input
HDMI 3 or 4.
19. VGA / 3D / numeric input 7
There is no VGA input on this projector.
Use with ALT to toggle the 3D Format setting between Off and Auto.
20. COMP1 / EYE / numeric input 8
There is no Component 1 input on this projector.
Use with ALT to switch between left and right eye 3D dominance.
21. ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
lTo assign an IR remote address:
1. Press and hold this button until the red indicator starts flashing.
2. Release this button and while the red indicator is still flashing, enter a two-
digit address using the numeric input buttons. The indicator will flash three
times quickly to confirm the change.
lTo unassign an address and return to the default address 00:
1. Press and hold ALT and this button simultaneously until the red indicator
flashes to confirm the change.
22. 3GSDI / B / numeric input 6
Select the 3G-SDI input.
23. TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern: White, Black, Red, Green,
Blue, Checkerboard, Crosshatch, V Burst, H Burst, Color Bar, Off..
When PIP mode is on, use this button with ALT to swap the main and sub images.
24. COMP2 / PIP / numeric input 9
There is no Component 2 input on this projector.
Use with ALT to switch on Picture In Picture (PIP) mode.
Installation & Quick Start Guide Rev B September 2019
page 19
Notes

Digital Projection Ltd. Titan Laser WUXGA Remote control
Infrared reception
40˚
40˚
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
Rev B September 2019
page 20
Installation & Quick Start Guide
Notes